|
![]() |
Overclock.net - Overclocking.net > Cooling > Air Cooling | |
Can i lap my Xigmatek HDT-s1283?
|
||
![]() |
|
|
LinkBack | Thread Tools |
|
|
#21 (permalink) | |||||||||||||
|
catmmm approved wierdo
![]() |
I got higher temps after my lap job too
__________________
Dig cars more than computers? Stop by CarForum.net!![]() ![]() ![]() ![]() E8400 C0 @ 4.3GHz on AIR ![]() ![]() ![]() Quote by Syrillian: "Nono!...Kill person." Windows 7||Fan Club The ß₤ứə Çřёώ The American Overclockers The Tux Club The Red Tide![]() Never Use Your Flash Drive the Same Again! Supercharge Vista! [F@H]View Your Fahmon From Anywhere! Member of Royal Navy GPU F@H Team
|
|||||||||||||
|
|
|
|
#22 (permalink) | |||||||||||||
|
NIF
![]() |
corry, does the AM2 socket need a bolt-through kit with the xig-s1283?
i know people get much better temps when they add the LGA775 bolt-through. does the AM2 use push pins?
|
|||||||||||||
|
|
|
|
#23 (permalink) | ||||||||||
|
*cough* Stock *cough*
![]() |
Lapping is overrated.
__________________
|
||||||||||
|
|
|
|
|
#24 (permalink) | |||||||||||
|
Intel Overclocker
|
had my heatsink with 120 on bottom (laying horizontal) , pushing thru heatsink , and facing 200mm on top of case pulling out. Just switched it vertical , with 120 on front Pushing through , 120 on back pulling , and 120 on case pulling right behind it , 1C drop only , and reapplied TIM , because my last application only had like 1/2 the cpu covered , it wasnt even centered!! *** is vertical overrated?
|
|||||||||||
|
|
|
|
|
#25 (permalink) | |||||||||||||
|
Overclocker
![]() |
No AM2 has no Bolt kits or push pins! We have clips!
__________________
|
|||||||||||||
|
|
|
|
|
#26 (permalink) | |||||||||||||
|
New to Overclock.net
![]() |
Does anyone have a pic of a lapped S1283? Thanks.
__________________
|
|||||||||||||
|
|
|
|
|
#27 (permalink) | ||||||||||||
|
AMD For Life
![]() |
Ok Hal.....
Are you sure your temps are accurate?!
__________________
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() : )![]() ![]() ![]() ![]() ![]() ![]() ![]()
|
||||||||||||
|
|
|
|
#28 (permalink) | |||||||||||||
|
Overclocker
![]() |
I think i do, i take a pic of all my PC parts before and after! I will check and post back!
__________________
|
|||||||||||||
|
|
|
|
|
#29 (permalink) | |||||||||||||
|
New to Overclock.net
![]() |
Cool thanks. What grit of sandpaper did you use and approximately how long did you lap it for? I'm kinda on the fence about this, I've been searching and some people have sanded through the heatpipe, so I'm a little bit worried. When I was lapping my SonicTower I didn't have to worry about it.
__________________
|
|||||||||||||
|
|
|
|
|
#30 (permalink) | |||||||||||||
|
4.0ghz
![]() |
Not if you're patient and know how to do it properly. It took 8C off my load temps.
__________________
|
|||||||||||||
|
|
![]() |
| Tags |
| amd, intel, lapping, temps, xigmatek hdt-s1283 |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|