|
|
|
 |
Overclock.net - Overclocking.net > Cooling > Air Cooling | |
Thor's Hammer PULL|PUSH
|
||
 |
|
|
LinkBack | Thread Tools |
02-26-09
|
#11 (permalink) | |||||||||||
|
AMD Overclocker
 
|
Those would be ok, but as long as you have the clearance, you'd probably want to get 120x38mm fans, they have better static pressure.
__________________
|
|||||||||||
|
|
|
02-26-09
|
#12 (permalink) | ||||||||||||||
|
Danke schön
 
|
Quote:
__________________
Check Out My Sammich!Aumotocnic"An unfortunate member of the overclock.net insomnia club" Missouri Overclockers The ß₤ứə Çřёώ The Red Tide ATi Owners Unite nVidia's Gr33N Machine
|
||||||||||||||
|
|
|
02-26-09
|
#13 (permalink) | ||||||||||||||
|
4.0 GHz
|
Before I go and order any ill go ahead and install my Hammer and move my ram over and get the measuring tape out. If I have room ill go for a 38mm. Only thing is that if I used one on the pull side it would almost be sitting flush against my exaust fan. So all the heat in my case would be almost trapped inside it.
__________________
Quote:
|
||||||||||||||
|
|
|
02-26-09
|
#14 (permalink) | ||||||||||||||
|
RUNRUNRUN I HUNGER COWARD
 
|
Quote:
And with 38mm fans, imo, push/pull setups aren't needed.
__________________
Rampage Torture Rack Build Log|Torture Rack|Antec 300|Antec 1200|Antec 1200 Night Photos|Antec 1200 Inside 50D (Sigma 30mm f/1.4 EX DC HSM | Nikkor 50mm f/1.2 | Nikkor 55mm f/1.2 | Canon EF-S 10-22mm f/3.5-4.5 USM | Canon EF-S 60mm f/2.8 Macro USM | Canon 70-200mm f/4L IS USM | Crumpler 7MDH | B+W filters) Images: Flickr OCN Team Fortress 2 Group
|
||||||||||||||
|
|
|
|
02-26-09
|
#15 (permalink) | |||||||||||||
|
AMD Overclocker
|
Sorry to thread jack but I just recently setup a push/pull on my xigmatek dark night but I ran into a problem. I was going to use 2 s-flex's but I had a problem with the fan on the side where there is no actual mounting. If the s-flex was too close to the heatsink, it would make a loud noise. To keep the fan quiet I would have to have it at least a 1/4 inch away from the heatsink, which I thought would be defeating the purpose of the push/pull setup. I found a spare cooler master fan (it was the back exhaust fan from my 690 case till I swapped it out for a s-flex) and when I put that directly on the heatsink it made no extra noise like the s-flex did. I left that on there for the push pull but after reading this thread I am a bit worried. Is the worse that could happen is the cooler master fan burns out? The setup keeps my cpu cooler by about 2-3 degrees celsius compared to just the s-flex mounted.
|
|||||||||||||
|
|
|
|
02-26-09
|
#16 (permalink) | |||||||||||||||
|
4.0 GHz
|
Quote:
__________________
Quote:
|
|||||||||||||||
|
|
|
|
02-26-09
|
#17 (permalink) | ||||||||||||||
|
4.0 GHz
|
Would there be a problem using my fan's that I have in my OP for a little? Maybe a week or 2?
Also im guessing if i did i would need the higher cfm on push and the lower on pull?
__________________
Quote:
|
||||||||||||||
|
|
|
|
02-27-09
|
#18 (permalink) | |||||||||||||||||
|
Cut costs
 
|
Quote:
Quote:
__________________
Quote:
Quote:
|
|||||||||||||||||
|
|
|
|
02-27-09
|
#19 (permalink) | ||||||||||||||||
|
4.0 GHz
|
Quote:
Im thinking of having the weaker Pulling at 100% all the time and the Pusher controlled by the bio's depending on temps. Sound ok?
__________________
Quote:
|
||||||||||||||||
|
|
|
|
02-28-09
|
#20 (permalink) | ||||||||||||||
|
4.0 GHz
|
It's between these: What would offer me the best performance/noise ratio? Remember it will be moving air through a dense 160MM cooler.
http://www.petrastechshop.com/12yalod1cafa1.html http://www.newegg.com/Product/Produc...82E16835705002
__________________
Quote:
Last edited by Sickened1 : 02-28-09 at 12:06 AM |
||||||||||||||
|
|
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|
