[Project] Loricatus Draco (Armored Dragon) {ever evolving} - Page 12 - Overclock.net

**thlnk3r** · 04-14-09

Quote:

Originally Posted by blitz6804

Thlnker: my NB CPU voltage is 80 mV over spec.

Blitz, what increments do you have for NB VID? Are you sure 0.08 volt increase was enough?

Good luck

N2Gaming · 04-14-09

blitz are you sure your mobo does not have the option to increase the chipset voltage? My bios says verbatum chipset voltage.

blitz6804 · 04-14-09

N2Gaming: I am not sure, no, but I do not think it is there. I can adjust the southbridge and the hypertransport, but I do not think I can adjust the chipset. (I will look again later.)

Thlnk3r: NB-CPU Voltage comes in 40 mV increments. One is enough to do 200x10. Two is enough to do 200x11 through 230x10. Three is not enough to run 200x12.

blitz6804 · 04-15-09

Uneventful night last night. I did try a lower-latency setting of what I had. It passes OCCT and a triple run of 3DMark06. Today, I will try throwing it through S&M and see what happens.

blitz6804 · 04-15-09

I threw S&M at it. FPU tests were up to 61º C before I pulled the plug. No good.

So I put it back to my OCCT-stable 3450 MHz and I am about to throw S&M at that.

N2Gaming · 04-15-09

Quote:

Originally Posted by blitz6804

I threw S&M at it. FPU tests were up to 61º C before I pulled the plug. No good.

So I put it back to my OCCT-stable 3450 MHz and I am about to throw S&M at that.

Good Luck w/S&M

blitz6804 · 04-15-09

Thanks. It is already on the PSU tests. I do not foresee any issues on the RAM tests considering my RAM is technically running sub-stock.

N2Gaming · 04-15-09

Quote:

Originally Posted by blitz6804

Thanks. It is already on the PSU tests. I do not foresee any issues on the RAM tests considering my RAM is technically running sub-stock.

Good job, I keep failing 3.6Ghz and can't remember what my settings were when I had it stable. Oh well. I guess it would be as good a time as any to try the New MX-2 TIM that was deliverd on monday.

blitz6804 · 04-15-09

It was stable in OCCT at 3.60 GHz with the following settings:

15x240
DDR2-800 divider
5-5-5-15
NB = 9x
HT = 8x

All others are "auto."

I did not like the temperatures it had in FPU, so I pulled the plug. At 3450 MHz, it is a more-reasonable 55.5º C. Though, I think I have my VCore higher than it needs.

cs_maan · 04-15-09

Quote:

Originally Posted by blitz6804

It was stable in OCCT at 3.60 GHz with the following settings:

15x240
DDR2-800 divider
5-5-5-15
NB = 9x
HT = 8x

All others are "auto."

I did not like the temperatures it had in FPU, so I pulled the plug. At 3450 MHz, it is a more-reasonable 55.5º C. Though, I think I have my VCore higher than it needs.

Whats your Vcore at 3450 MHz?
I got mine that high with just +.025 for the Vcore, I don't think it even needs that much.

		Overclock.net - Overclocking.net > AMD > AMD - General > AMD Build Logs
[Project] Loricatus Draco (Armored Dragon) {ever evolving}

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)