Budweiser

Hi.


Just thought i would post my overclock for my AMD 2500 -M-

AMD 2500 -M- @ stock 1862mhz
AMD 2500 -M- @ 2.42 Ghz = 11x 220 FSB with normal coolermaster cooling,
AMD 2500 -M- @ 1.648 v, it died on me with 1.584 v,
AMD 2500 -M- Temps, idle 42c, load 49c, thats with side panel off, reason for this as my side panel is damaged right now so cant put it on until i get my new case.

OH, im using the ASRock K7VT6 motherboard, (soon to be the Abit NF7 - S v2 board)

My first post!!!

Thanks, please others compare with similar system, would love too see

dongchen_han

Welcome to the Forum, Asrock are cheap and they have a better harddisk speed, but the performance of overclock are soo poor. i own one NF7 2.0 and my normal barton 2500+ @ 2.4Ghz ultra stable with 1.725volt. I coundnt be happier. PS: 2.4GHZ AthlonXp = 4.0Ghz Pentium 4 on my Sisoftware Sandra 2004!!

__________________
M82A1

BF2 username [X1X]-=+XoX1de+=-

Budweiser

Well i got this @ just over 2.4 Ghz and its running perfectly stable, like i said though my NF7 - S v2 should be here tomorrow.

Xavier1421

1.648V for cpu at 2.4G's is quite impressive...

Have you Prime95'd it??

I think you'll like the NF7 more...you may even get a better OC

__________________
Retirement isn't all it's cracked up to be

Budweiser

Yeah alot of people said i will like my NF7 board better, and im looking forwards too it coming. yeah i have prime95'd this cpu and its fine, temps are depending on the room temps, like now my temp on my cpu has gone from 42c idle too 45c idle, as i have switched my fan heaters on in the living room, i reckon i could get higher with this board with higher voltages, but then i think i may have a high temp problem.


Update::: Just prime95'd it again with the fan heater on in the living room, its pretty hot in here, and my temp went from 45c, idle upto 51-52c, kept flicking between the two.

OH, this is with the side panel off on the case too,,, its damaged so cant put it on you see...

__________________
REP Me if ive been helpful

Ravage81

I'm also using the NF7-S V2.0 board and its great for overclocking, its got large variety of settings to tinker with. I just got a new heatsink and fan, and a new case. Now I have reached an overclock of 2.6Ghz and my temps are 40C @ idle and 45.5C @ full load. I used Prime95 to test and it ran for over 2.5hrs with no errors.

Settings used - 217 X 12 @ 1.9Vcore, Vdimm 2.7, Chipset Voltage 1.6

I tried overclocking more but I couldn't get it to run stable in Prime95, I would get bluescreened and rebooted. This could be a board limitation? since I believe that the NF7-S V2.0 is only rated for 200FSB.

blob

Also have I the NF7-S 2.0

208x12.5 ~2600MHz 1.8V stable, 38C Idle 43C Load

__________________

mjs1231

lol thats weak

amd 2500 + pre week 34 @ 2900 mhz @ 552 fsb

on a nf7-s rev 2.0

with a pc power and cooling 510 psu

multimeter tested

system cooled with asestek liquid cooling kit chipset cpu and gpu

use a mix of aqua syntek and de ionized water

3 months and is still crystal clear

i own u all
lol

dont hate

blob

Dude I dont have that anymore and I have a no name PSU with 400W. 18A 12V rail thats at 11.4V under load. So 2600 was pretty good. I used to get to 2700, but my performance of my psu has been declining over the months. So I'm saving for a powerstream.

Give a screenie too.

__________________

Sai_Jao

yes defo go fot the nf7-s(2) graat clocker
dont mean to hijack this post but didnt no 2.4 @1.68 was good (mine 2.4@1.58 )

552 FSB !!!! - How?

Attached Thumbnails