Overclock.net banner

Antec1200&DF-85 Case Modding...

13K views 52 replies 19 participants last post by  rikuntyudady 
#1 ·
Hello,everyone.
Thank you for the comment in the last thread.

It's my gear(haf932mod)

Antec1200 and DF-85 are up-loaded this time.
When time though still being produced can be done, I will add DF-85 again.

[Antec 1200]
The top board part of Twelve Hundred is remodeled.
The side pocket part is cut down, and painted.
picture.php?albumid=4399&pictureid=25093


picture.php?albumid=4399&pictureid=25094


Tape LED is installed.
picture.php?albumid=4399&pictureid=25095


Confirmation of lighting.
picture.php?albumid=4399&pictureid=25096


The label film printed on the acrylic sheet is put, and it puts it up.
picture.php?albumid=4399&pictureid=25076


The same EL wire as last time is installed in the reception desk part.
picture.php?albumid=4399&pictureid=25097


Because the logo part of Antec was a metallic plate, it uses it as a touch switch.
picture.php?albumid=4399&pictureid=25098


Movie http://youtu.be/vBIIxtJl5Cs

It's done.
picture.php?albumid=4399&pictureid=25074


picture.php?albumid=4399&pictureid=25075


[Antec DF-85]

Here still customized the reception desk part for the time being though on the way.

Starting constructing from upper fleet door.
picture.php?albumid=4400&pictureid=25080


picture.php?albumid=4400&pictureid=25099


picture.php?albumid=4400&pictureid=25082


picture.php?albumid=4400&pictureid=25100


Lower fleet door.

picture.php?albumid=4400&pictureid=25083


picture.php?albumid=4400&pictureid=25084


picture.php?albumid=4400&pictureid=25085


picture.php?albumid=4400&pictureid=25087


It paints in gun metal.
picture.php?albumid=4400&pictureid=25086


To apply LED, it paints thinly.
picture.php?albumid=4400&pictureid=25088


This chip LED is used.
(It is 3mm in the vicinity of length. )
picture.php?albumid=4400&pictureid=25089


To place it from both sides, it installs it.
picture.php?albumid=4400&pictureid=25090


Check on lighting.
picture.php?albumid=4400&pictureid=25091


picture.php?albumid=4400&pictureid=25078


picture.php?albumid=4400&pictureid=25079


Here slowly proceeds work.
It is scheduled to add a postscript little by little.

Thank you
smile.gif
 
See less See more
25
#5 ·
Quote:
Originally Posted by Hukkel;13630548
Looks great. Creativity ftw. I like the 1200 the best.
Thank you for your comments.
smile.gif

Antec1200 is a case to have had a still enough function.
 
#9 ·
Man that 1200 is wicked!
 
#11 ·
Quote:
Originally Posted by adizz;13842624
Man that 1200 is wicked!
Thank you for your comments.
I do not understand a true meaning of the word because it can't English well.
confused.gif
 
#12 ·
The painting of Side panel was completed.
picture.php?albumid=4400&pictureid=25785


It assembled it.
It is an whole image.
picture.php?albumid=4400&pictureid=25786


Lighting of illumination.
It is scheduled to control individually turning on a switch.
It might be also interesting to make brightness can controlled by connecting it with FAN Controller.
picture.php?albumid=4400&pictureid=25787
 
#15 ·
Diamond Plate, Bullret Hole, Gun Smoke, Metal panel & Rivet, and Metal Tears Effect were added to the side panel of Antec1200.
It has become the overall confused design when a variety of adding it because I wanted to use the airbrush.
frown.gif


picture.php?albumid=4399&pictureid=25845
 
#17 ·
Quote:
Originally Posted by scatology;14003386
I'm not a fan of this king of case but your one is amazing... Nice paint job!
It wants to practice the airbrush more, and to become good.
Your comment gave the power.
Thank you for your positive comments:)
 
#18 ·
It started customizing inside of "DF-85"
After the acrylic bord had been processed, "3M Di-noc" was put.
Part was clipped to the shape of the "DARK FLEET".

An acrylic board of the smoke is piled up to an acrylic board of translucent white.
Part used the acrylic sheet of the transparency.
The logo part puts the one printed in the label sheet.

It is a technique also here used before.
It's my gear (haf932mod)







Tape LED is installed like this.


It is such a state when lighting.






It is not completion yet.
Thanks.
 
#20 ·
Quote:
Originally Posted by Alatar;14135157
Awesome job man... Absolutely great!

I look forward to seeing more
smile.gif
Thank you for your positive comments:)
I keep remodeling it continuously.
 
#22 ·
Looks great man! Its very inspiring to look at. Keep up the good work!
 
#23 ·
Quote:
Originally Posted by italoxx;14141297
Hello, I'm Brazil. I really enjoyed your work, I have the same case as yours.

I would like to make the same modifications and know how much I spend. If you can help.

You do a fantastic job, congratulations.
Hello,thanks for your comments.
i'm in Japan.
Is your case DF-85??Or, is it TwelveHundred??

Painting is included in the processing of "TwelveHundred", and it has contracted for one week at the period.
Moreover, cost is about 100 U.S dollars.

It still took about one week to process "DF-85" here including painting though on the way.
Cost is about 80 U.S dollars.

The processing of the acrylic sheet in 5.25-inch bay part ended in a day.
 
#24 ·
Quote:
Originally Posted by Farmer Boe;14141704
Looks great man! Its very inspiring to look at. Keep up the good work!
Thank you for your positive comments:)
I continuously enjoy remodeling.
biggrin.gif
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top