|
|
|
09-17-08
|
#1921 (permalink) | ||||||||||||||
|
Networking Nut
 
|
Quote:
|
||||||||||||||
|
|
|
09-17-08
|
#1922 (permalink) | ||||||||||||||
|
New to Overclock.net
|
Quote:
__________________
Check out my acrylic tech station
|
||||||||||||||
|
|
|
09-18-08
|
#1923 (permalink) | |||||||||||
|
Case Modder
|
Amazing work
 +  btw, do you still use Dremel for any of the cuts? Which bit do you use (if that's not your trade secret  )?
|
|||||||||||
|
|
|
|
09-19-08
|
#1924 (permalink) | |||||||||||||
|
my time is just beginning
 ![[PWN]Schubie's Avatar](http://www.overclock.net/customavatars/avatar52172_12.gif){kind=avatar}
|
 prove me wrong Syr and give us an update!
__________________
 Overclock.net Downloads SectionOverclock.net Backpacking, Camping and Climbing Thread
|
|||||||||||||
|
|
|
09-19-08
|
#1925 (permalink) | |||||||||||||
|
Damage, Inc.
 
|
Update: 09.19.08
Trimming the fat.
I took some time to pare down the wiring and to eliminate the lighting switches on the CCFL lights, painted the inverter housings and sleeve all the wiring: The third inverter is for the single (I may add the second lighting tube) CCFL that is mounted in the tube below the motherboard.  Took 3 sets of these:  ...and kept only these parts:  When re-doing wiring that involves splicing I like to solder the connections. There are any number of ways that are effective, but this is the manner that I have found to work well for me: A "3rd hand" is always a welcome addition:  Although the tension in the clips is not enough to break the insulation I still like to clamp on the metal portions:  Then:    Note: Heat the work, not the solder. A small piece of heatshrink works well for insulation. Also I stagger the breaks in the wiring to ensure that a short will not occur, and to prevent the "boa-constrictor" look of potential bulges in the line.  Sleeved and ready to illuminate:  note: It is advisable to check that the lighting works periodically throughout the process. ...and I am still sanding and shaping the rear panel  ... my thumb hurts (wah!)
__________________
WIP: Scarab Custom Cases: Silentium, Halcyon, Indigo, Gemini, Prometheus, Anvil Case Mods: Liquid Chameleon, VF1000 LAN box Semper Fidelis
Last edited by Syrillian : 09-19-08 at 08:36 AM |
|||||||||||||
|
|
|
|
09-19-08
|
#1927 (permalink) | ||||||||||||||
|
Scarring Your Psyche
 
|
I hope you realize that Bro-mance can induce delirium, hysterical girlish laughter and a lack of funds the night after...
Not to mention jealousy...from wimmen
__________________
Quote:
|
||||||||||||||
|
|
|
|
09-19-08
|
#1928 (permalink) | |||||||||||||
|
Damage, Inc.
|
Di...did...did you just say "Bro-mance" ?!?!?!?!
Bwahahahahaha! I wish I had a GF or Wife.... I would so rub that in her face! "Bro-mance" Hahahahahahaa.... I love it. *high-five*
__________________
WIP: Scarab Custom Cases: Silentium, Halcyon, Indigo, Gemini, Prometheus, Anvil Case Mods: Liquid Chameleon, VF1000 LAN box Semper Fidelis
|
|||||||||||||
|
|
|
|
09-19-08
|
#1929 (permalink) | ||||||||||||||
|
Scarring Your Psyche
|
Owwww...that was my bad hand...
__________________
Quote:
|
||||||||||||||
|
|
|
|
09-19-08
|
#1930 (permalink) | |||||||||||||
|
Damage, Inc.
|
oopsies...
__________________
WIP: Scarab Custom Cases: Silentium, Halcyon, Indigo, Gemini, Prometheus, Anvil Case Mods: Liquid Chameleon, VF1000 LAN box Semper Fidelis
|
|||||||||||||
|
|
|
 |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|
