MCBrown.CA

Yes, I suppose that's a point you've got there...



EDIT: I recognized the D40 charger in one of the first pics! I have one as well but only with the kit 15-55mm lens. Nice little camera...

__________________

xguntherc

yup.. I have the D40, with the Kit lens, the 55-200mm, and the D90's kit lens. (But no D90 ;( the 18-105mm VR.. thats a nice lens so far.

__________________
H20 Loop: Swiftech Apogee GTZ, Feser TFC360 RAD w/ 3 Yate Loon D12SM, MCP-655 D5 Vario, Micro Res v2, Masterkleer 7/16 ID, DD "FatBoy" 1/2 Barbs, Pentosin G11 Blue. 28c Idle, 39c Load

Project HAF Water-Cooled
3DMark06 High Score 21,710 http://service.futuremark.com/compare?3dm06=9678912
Best Overclock, & There's More to Come http://valid.canardpc.com/show_oc.php?id=491589

Official OCN Camera Club
|Nikon D40| |18-105mm f/3.5-5.6 VR| |55-200mm f/4-5.6 VR|

xguntherc

The rad will be mounted up top. with the barbs at the back.. the pump will be in the HD bay, and the RES is the question I'm still not sure on yet.

Here's some pictures. I went head and sleeved the Pump's wires today also.


Close-Up of Sleeving


Here's a view of it, there's this slot, gap thingy on the back right there were I can run the tube to the top. So I'll be doing that. and then I'm trying to decide to have my RES be either right there that's pictured, or have it on the left side in front of the 1-3 PCI slots.. but if I did it that way, I'd have another long tube running to the filport.


what ya guys think, how should I mount it all.

__________________
H20 Loop: Swiftech Apogee GTZ, Feser TFC360 RAD w/ 3 Yate Loon D12SM, MCP-655 D5 Vario, Micro Res v2, Masterkleer 7/16 ID, DD "FatBoy" 1/2 Barbs, Pentosin G11 Blue. 28c Idle, 39c Load

Project HAF Water-Cooled
3DMark06 High Score 21,710 http://service.futuremark.com/compare?3dm06=9678912
Best Overclock, & There's More to Come http://valid.canardpc.com/show_oc.php?id=491589

Official OCN Camera Club
|Nikon D40| |18-105mm f/3.5-5.6 VR| |55-200mm f/4-5.6 VR|

Doomtomb

What sleeving kit are you using? And wouldn't your tubing get in the way of your hard drives? Just make sure you allow slack to get around your hard drives.

Looks superb so far.

xguntherc

I'm using some sleeving kit I got at my local Fry's Electronics.

and as for the HD's. I only have 1. so I'm not to worried about that. it will fit, but I could always put it in front of the PSU to be safe.

__________________
H20 Loop: Swiftech Apogee GTZ, Feser TFC360 RAD w/ 3 Yate Loon D12SM, MCP-655 D5 Vario, Micro Res v2, Masterkleer 7/16 ID, DD "FatBoy" 1/2 Barbs, Pentosin G11 Blue. 28c Idle, 39c Load

Project HAF Water-Cooled
3DMark06 High Score 21,710 http://service.futuremark.com/compare?3dm06=9678912
Best Overclock, & There's More to Come http://valid.canardpc.com/show_oc.php?id=491589

Official OCN Camera Club
|Nikon D40| |18-105mm f/3.5-5.6 VR| |55-200mm f/4-5.6 VR|

Doomtomb

What is that around the end of the sleeves? I've used electrical tape before and it doesn't really seem to hold very well.

DUNC4N

Shrink tubing

Oh, and subbed. Keep up the good work.

__________________

slickwilly

that is called heat shrink sleeve, it is available at most auto parts stores

__________________
folding for the cause.
Originally Posted by Shrimpykins When you try to overclock your whiskey sour by using dry ice instead of normal ice.

woop - OhMyGodPower - slickwilly - csm11

xguntherc

yes, heat shrink tubing. Just get a hot gun, or a hair dryer. I use a Lighter and hold it farther away than you'd think, and it slowly shrinks up tight. looks good huh. It's my new addiction. I want to sleeve everything. but I don't wanna buy the Pin Tool and all that and do the PSU, thats just to much work.

I mounted the RAD up top, with the fans, and the Pump down below but farther back to help the tubing. and I'm about to mount the Res, then I'll take pics and start my leak test.

__________________
H20 Loop: Swiftech Apogee GTZ, Feser TFC360 RAD w/ 3 Yate Loon D12SM, MCP-655 D5 Vario, Micro Res v2, Masterkleer 7/16 ID, DD "FatBoy" 1/2 Barbs, Pentosin G11 Blue. 28c Idle, 39c Load

Project HAF Water-Cooled
3DMark06 High Score 21,710 http://service.futuremark.com/compare?3dm06=9678912
Best Overclock, & There's More to Come http://valid.canardpc.com/show_oc.php?id=491589

Official OCN Camera Club
|Nikon D40| |18-105mm f/3.5-5.6 VR| |55-200mm f/4-5.6 VR|

procpuarie

looks good!

__________________