|
|
 |
Overclock.net - Overclocking.net > Case Mods & Cases > Case Mods - General Discussion | |
Need some Case Molding thinglets...
|
||
 |
|
|
LinkBack | Thread Tools |
04-11-07
|
#1 (permalink) | |||||||||||||
|
Audiophile
|
Need some Case Molding thinglets...
I cut my case for a side panel, and I need some molding to making it look nicer, couse it's not all that even. Where Can I get some? or what can I use for that? I'll have some pics up later but I need to buy them.
__________________
-DeeJay1337-
- > My Tut on "Washing" a Keyboard < -  Knowledge is often mistaken for intelligence. This is like mistaking a cup of milk for a cow.   My computer beat me at chess the other day...But it was no match for me at Kickboxing.
|
|||||||||||||
|
|
|
04-11-07
|
#2 (permalink) | ||||||||||||||
|
Overclocker
|
auto store?
__________________
Quote:
|
||||||||||||||
|
|
|
04-11-07
|
#3 (permalink) | |||||||||||||
|
New to Overclock.net
|
auto store or home depot I would say
__________________
http://valid.x86-secret.com/show_oc.php?id=183426 Super Pi 13.834s Pics http://s152588970.onlinehome.us/PiCs...%20(Large).jpg http://s152588970.onlinehome.us/PiCs...%20(Large).jpg http://s152588970.onlinehome.us/PiCs...%20(Large).jpg http://s152588970.onlinehome.us/PiCs...%20new%202.JPG
|
|||||||||||||
|
|
|
|
04-11-07
|
#4 (permalink) | ||||||||||||||
|
Windows Wrangler
|
UK users can get the stuff from http://www.kustompcs.co.uk/
__________________
Quote:
|
||||||||||||||
|
|
|
|
04-11-07
|
#5 (permalink) | ||||||||||
|
News Fiend
|
It sounds like you're looking for door edge molding for this mod. It can be picked up at any local auto store. It should be about 5 bucks and usually comes in strips of 2. It is U-shaped (see pic) and has an anhesive in the middle so that it stays put. I'm using the clear molding on my side panel. I'll take a pic of it to show you what I mean when I get back to my comp.
|
||||||||||
|
|
|
|
04-11-07
|
#6 (permalink) | |||||||||||||
|
Audiophile
|
Ok, couse that would help me quite some bit. Thanks
__________________
-DeeJay1337-
- > My Tut on "Washing" a Keyboard < - Knowledge is often mistaken for intelligence. This is like mistaking a cup of milk for a cow. My computer beat me at chess the other day...But it was no match for me at Kickboxing.
|
|||||||||||||
|
|
|
|
04-11-07
|
#7 (permalink) | |||||||||||||
|
PC Gamer
|
__________________
Aumotocnic "An unfortunate member of the overclock.net insomnia club"
|
|||||||||||||
|
|
|
|
04-17-07
|
#8 (permalink) | ||||||||||||
|
Overclocker in Training
|
Also there is a wide selection from McMaster-Carr
__________________
Quote:
|
||||||||||||
|
|
|
|
04-17-07
|
#9 (permalink) | |||||||||||||
|
PC Gamer
|
I think Im missing some obvious element when it comes to molding I dont see how a sing U channel would work. How is the window held in place unless the molding was a double U with their bottoms touching? Do you usually put the single U molding on the edge and adhere the window behind the molding by other means? I made a lot of cuts recently and put mesh over the cuts and I wouldnt mind molding it if I could figure out this simple step XD
__________________
Check Six x6.dBs|Xfire: decibels
|
|||||||||||||
|
|
|
|
04-17-07
|
#10 (permalink) | ||||||||||||
|
Overclocker in Training
|
Most people I've seen just use U-channel to cover the edges and then over cut the panel so they can use screws or strong mounting tape (or glue or various other things) to adhere the panel to the case. Bill Owen at MNPC recommends Scotch Brand Heavy Duty clear tape #4010 to mount thing.
__________________
Quote:
|
||||||||||||
|
|
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|
