CattleRustler

added two additional pics to the end of the first post.
glad that pcie cable is gone

__________________

[Current Project] PolymorphiX v2 (alu & steel alu hybrids)
[Pending finish] Butcher's Hook (Slipknot tribute bench in steel)
[mod2hardware] All Modding Projects by CattleRustler
[mod2software] WorklogCreator 1.0.1.6 visually build postable worklogs, quickly & easily with drag and drop

xHassassin

Ugh, my case is even more messy, only problem is, most of the case is plastic, so I can't cut anything, even if I did have the tools...
I decided to stuff everything into the DVD drive slots, made it look a bit better.
Great job though!

CorporalAris

Is it a coincedence that the most blurry picture is after the beer? Hmmm...

Anyways, I like it. It makes me want to mod my case...

__________________
I am 61% addicted to Counterstrike. What about you?

CattleRustler

thanks xHassassin

thanks - - haha! yeah, then the cutting began - LOL

I still have all my fingers

__________________

[Current Project] PolymorphiX v2 (alu & steel alu hybrids)
[Pending finish] Butcher's Hook (Slipknot tribute bench in steel)
[mod2hardware] All Modding Projects by CattleRustler
[mod2software] WorklogCreator 1.0.1.6 visually build postable worklogs, quickly & easily with drag and drop

Darkice

Do not know if any body told you this or not yet but I Got a killer tip for you if not.

Ok you know how you put some plastic over your cut hole and it doesn't look to clean right...

well here we go the trick go to hardware store buy a roll of the window screen seal rubber and cut and splice it and it will slide over your cut and stay and look super clean.

__________________
Remember...there is a littleEvilIn Everyone

UK King's
Umbra Rendering Optimization Middleware I think we should support them

ß₤ứə Çřёώ
Gr33n-Machine

CattleRustler

yep, I am aware of the options with that - but thanks +rep
this case is going back under the knife at some point, theres a few more things I want to tweak out

__________________

[Current Project] PolymorphiX v2 (alu & steel alu hybrids)
[Pending finish] Butcher's Hook (Slipknot tribute bench in steel)
[mod2hardware] All Modding Projects by CattleRustler
[mod2software] WorklogCreator 1.0.1.6 visually build postable worklogs, quickly & easily with drag and drop

Darkice

Well your welcome just trying to help you a little sense you helped me so much

__________________
Remember...there is a littleEvilIn Everyone

UK King's
Umbra Rendering Optimization Middleware I think we should support them

ß₤ứə Çřёώ
Gr33n-Machine

CattleRustler

appreciated

__________________

[Current Project] PolymorphiX v2 (alu & steel alu hybrids)
[Pending finish] Butcher's Hook (Slipknot tribute bench in steel)
[mod2hardware] All Modding Projects by CattleRustler
[mod2software] WorklogCreator 1.0.1.6 visually build postable worklogs, quickly & easily with drag and drop

j_syk

Was the 4 pin connected to your motherboard long enough to go around the back and back through the top? or did you get an extension? Mine is too short :cry: but I fit it nicely between my gpu and mobo. see my gallery it's still pretty clean. I'm going to tweak my cable management a little more soon, i'll put up more pics then.

Great work!

__________________

CattleRustler

thanks

no, I had to use an extension

__________________

[Current Project] PolymorphiX v2 (alu & steel alu hybrids)
[Pending finish] Butcher's Hook (Slipknot tribute bench in steel)
[mod2hardware] All Modding Projects by CattleRustler
[mod2software] WorklogCreator 1.0.1.6 visually build postable worklogs, quickly & easily with drag and drop