The real Green Machine (lots of pics, have fun 56K) - Page 4 - Overclock.net

Rayce185 · 07-11-09

Thanks DaftFully

Quote:

Originally Posted by 18 is # 1

Those Blade may get to 1000 MHz at 4-4-4. Try a higher FSB and lower multi.
You should boost the Vcore to 1.3625 (Intel's top approved voltage) until you are stable and finished. You may need to boost MCH to 1.4v as well.

The BIOS Vcore in the above picture is 1.3750... That's what I'm complaining about.

That would give me a tolerance of about 0.04V, meaning for an actual 1.3625V I'd need to up the BIOS Vcore to 1.40, right?

And I just redid the same test as above, but with a BIOS Vcore of 1.3850... and an idle CPU-Z Vcore of 1.352, under load it was 1.288:

And this is my current "setup",

18 is # 1 · 07-11-09

What is your PL?
And MCH?

Rayce185 · 07-11-09

I'm not sure what you mean (Can't find it in the BIOS), but I just made some pics of my settings doing the last run:

Rayce185 · 07-11-09

So I'm running an unlinked setup now. Same voltages, same multiplier, but an FSB of 450MHz and the proper 600MHz RAM. Everest shows the same bandwidth for the RAM, the L1 and L2 are slightly higher, SuperPi has about the same time. But Linx is crunching almost 42GFlops in under 57s now, much better than the previous linked run!

EDIT: The board doesn't seem to like the unlinked setup, thy system hung itself up. I'm going to up the Vdimm to 1.85V

18 is # 1 · 07-11-09

PL=Performance Level or tRD
Download the most recent Memset and it will show you: http://www.tweakers.fr/memset.html

CudaBoy71 · 07-11-09

teh conductive ink will do the same as teh HB pencil...The ink is just permanent.

Rayce185 · 07-11-09

Quote:

Originally Posted by 18 is # 1

PL=Performance Level or tRD
Download the most recent Memset and it will show you: http://www.tweakers.fr/memset.html

I downloaded the newest 4.1 beta and the standard 4.0, and both DIDN'T show me the memset menues I have been seeing on here... I was wondering if this has to do with Windows/x64 or the drivers for it...

Quote:

Originally Posted by CudaBoy71

teh conductive ink will do the same as teh HB pencil...The ink is just permanent.

Well I can always use alcohol to rub it back off

The Vcore mod says "to ground"... how am I to connect that?

Ultrasonic2 (muffy) · 07-12-09

Rayce185 i see you haven't shared our little secret yet ?

sdla4ever · 07-12-09

oh a secret aye... well rayce you should get this set up CC is waiting to hear from their new member...

Rayce185 · 07-12-09

I'm struggling with the TRUE lapping.

I got this "lapping kit" on ebay since it has basically everything in it that one would need: Different grit sandpaper, three grit sizes of lapping compound and a buffing cloth (small piece of micro fibre =/ ).

Well the roughest sand paper is 220 grit and it's worn off already as it is maybe a quarter of the size than the paper you'd normally get in a hardware store, and stores are closed on Sundays over here...

For reference again: The crappy OEM surface.

My sanding panel. Neoprene ("anti slip mat"), glass, sand paper.

30min passed. Either the paper isn't rough enough, or the nickel coating is really hard. But the progress is SLOW. Also, signs of the TRUE's unevenness are showing

60min passed. Getting there, but still very slowly. Signs of the sand paper's wear are showing.

70-90min passed (can't remember the exact length as I was still quite drunk from partying shortly before). This is how far I got before falling asleep on the floor. The paper is hardly sanding anymore.
I am in distress.

Session two, four hours later (Don't ask me why I woke up so early). About 20min of sanding, the difference little to nothing.
I am not happy. Sand paper feels as rough as newspaper and the friends are still as sleep (want to ask if they may have any paper).

As you can see, the TRUE's base is incredibly uneven. I still can't figure out why Thermalright didn't give it a proper treatment, as it isn't really considered a cheap cooler. Even my 25€ Scythe backup cooler came lapped, what gives?

07-12-09	#38 (permalink)
Ultrasonic2 (muffy) Extreme Cooler Join Date: Jun 2007 Location: Auckland New Zealand Posts: 2,069 Rep: 130 Unique Rep: 76 Trader Rating: 1	Rayce185 i see you haven't shared our little secret yet ? __________________ FOR SALE Universal 62mm TEC Plates for W/C or Air coolers Everything you've wanted to know about TEC's

		Overclock.net - Overclocking.net > Intel > Intel - General > Intel Build Logs
The real Green Machine (lots of pics, have fun 56K)

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)