|
|
|
11-13-08
|
#311 (permalink) | ||||||||||||
|
New to Overclock.net
|
ohhh. Im really sorry. I had never changed it before... What is Vdroop?
__________________
|
||||||||||||
|
|
|
11-13-08
|
#312 (permalink) | |||||||||||||
|
New to Overclock.net
|
the difference in voltage in your bios to actualy vcore amount
__________________
P5N-E Bios Flash Utility
|
|||||||||||||
|
|
|
|
11-13-08
|
#313 (permalink) | |||||||||||||
|
Intel Overclocker
 
|
It is how much the voltage drops under stress.
__________________
Intel Q6600 G0 3.60GHz  Sapphire 4890 930Mhz/1060Mhz 3D Mark Scores: 3DMark06 17723 , Vantage P11771
|
|||||||||||||
|
|
|
|
11-13-08
|
#314 (permalink) | |||||||||||||
|
Programmer
|
Passed Prime95 after 22 hours without any errors. I think that's good enough for now! Time for some benchmarks.
Proud to say I'm running stable at 3.0ghz with my Q6600 on my P5N-E SLI  EDIT: Here's my validation http://valid.x86-secret.com/show_oc.php?id=446053
__________________
Last edited by xtascox : 11-13-08 at 10:52 PM |
|||||||||||||
|
|
|
|
11-14-08
|
#315 (permalink) | ||||||||||||
|
New to Overclock.net
|
Thanks a lot ... So, I didnt changed NB Voltage before... I will try your configuration xtascox and i will tell you the results ... Thanks a lot... rep +
__________________
|
||||||||||||
|
|
|
|
11-24-08
|
#316 (permalink) | ||||||||||||
|
New to Overclock.net
|
Using http://www.overclock.net/intel-cpus/...ml#post3489821, I was finally able to get mine stable at 3.0ghz.
__________________A few changes though for me. I set the LTD frequency to 3x and I ended up with memory timings 4-4-4-12 1t. I can confirm you need a northbridge cooler and a decent cpu cooler to pull it off. I left all volts as auto believe it or not. I might could turn them down a bit to decrease heat, but at load only 61 /shrug. I wanted tighter memory timings, but I just wasn't happy with the results. I am using kingston ram too lmao. http://valid.x86-secret.com/show_oc.php?id=451118
Last edited by floppydrivez : 11-25-08 at 10:51 AM |
||||||||||||
|
|
|
|
11-30-08
|
#317 (permalink) | ||||||||||||
|
New to Overclock.net
|
*sigh* i think ill just stick with my 2.64ghz b/c i have the b3 stepping and anything over that i cant even get into windows
__________________ it sucks b/c i have watercooling and anything over the 10% overclock doesnt work...i didnt try lowering the memory mhz though but w/e
Last edited by Tobysauce77 : 11-30-08 at 01:21 PM |
||||||||||||
|
|
|
|
12-02-08
|
#318 (permalink) | ||||||||||||
|
New to Overclock.net
|
well ive tried like everything and it refuses to get close to 3ghz...at least start up in windows...i can get it there but windows wont start...*sigh*
__________________o well ill just rejoice when i get a better mobo on my next build with a corei7 cpu
|
||||||||||||
|
|
|
|
01-02-09
|
#319 (permalink) | ||||||||||||
|
New to Overclock.net
|
I have this configuration:
__________________CPU: C2D Q6600 G0 cooler: Scytle Ninja rev.B MB: Asus P5NE-SLI bios v.0608 memory: 2x2GB patriot 800MHz LLP psu: Enermax liberty 500W and i am going with these settings 100% prime95 stable: BIOS: unlinked mod FSB> 1380MHz ram> 690MHz CPU voltage> 1.35V ram voltage> 2.175V chipset> 1.3xxV 
|
||||||||||||
|
|
|
|
01-02-09
|
#320 (permalink) | ||||||||||||||
|
Programmer
|
Quote:
It looks like you only ran prime 95 for 30 minutes? I would run it at least 8 hours to consider it stable... But if you can get it for that long, good job!
__________________
|
||||||||||||||
|
|
|
 |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|
