|
|
|
05-25-08
|
#141 (permalink) | |||||||||||||
|
Intel Overclocker
 |
Quote:
Thanks for posting those results. Clearly my RAM is holding back my system's performance, but not toooo terribly.
__________________
Pictorial Lapping Guide--Check this out if you're thinking of lapping an HSF and/or IHS!! ASUS P5N-E OCing Guide Best RAM timings guide I've seen "Incorrect using it may cause your system broken. For power End-User use only!" -Gigabyte MB manual (8I865GME-775-RH-Rev2.0)
|
|||||||||||||
|
|
|
05-25-08
|
#142 (permalink) | |||||||||||||
|
New to Overclock.net
|
I need some help for O/C my memory the tests and the numbers was from auto bios!!!!
__________________What ever i tryed is worst than this results... Which programm should i use because in Abit bios(sucks) i can't change all exept CL. A! And something else with memset i only see the values, can't change them because it says MCHBAR is locked....
Last edited by wat3rb0y : 05-25-08 at 04:10 PM |
|||||||||||||
|
|
|
|
05-26-08
|
#143 (permalink) | ||||||||||||
|
Intel Overclocker
|
i wouldn't recommend tweaking with memset... I haven't tried it, but using software to tweak memory timings just seems like bad news to me.
i'm not exactly sure what you're asking for... you've got those dimms running way over their stock speed--you're gonna have to have loos-ish timings. If you're at 5-5-5-18-2T I'd just live with it if I were you.
__________________
Pictorial Lapping Guide--Check this out if you're thinking of lapping an HSF and/or IHS!! ASUS P5N-E OCing Guide Best RAM timings guide I've seen "Incorrect using it may cause your system broken. For power End-User use only!" -Gigabyte MB manual (8I865GME-775-RH-Rev2.0)
|
||||||||||||
|
|
|
|
05-26-08
|
#144 (permalink) | ||||||||||||||
|
Programmer
|
Quote:
 .
|
||||||||||||||
|
|
|
|
05-26-08
|
#145 (permalink) | ||||||||||||
|
New to Overclock.net
|
This is my settings
I'm @ 3.4 Ghz so anyone with similar mobo can try. Using the zalman 9700 cpu cooler, I tried using my aquagate s1 again and it wouldn't even boot right @ 3.1 or anything higher..and my NB was running so hot, it's weird, I guess this board doesn't like it.
__________________FSB=1813 Vcore=1.36875 PLL=1.66 VTT=1.46 NB=1.52 SB=1.50 1.2V HT=1.60 Visualization=Enabled. 3Dmark06 = 17192 http://service.futuremark.com/compare?3dm06=6878755
|
||||||||||||
|
|
|
|
05-26-08
|
#146 (permalink) | ||||||||||||
|
Intel Overclocker
|
that vcore is over the recommended voltage for the chip... you should keep in mind that regardless of temps you may be degrading your chip with that vcore.
__________________
Pictorial Lapping Guide--Check this out if you're thinking of lapping an HSF and/or IHS!! ASUS P5N-E OCing Guide Best RAM timings guide I've seen "Incorrect using it may cause your system broken. For power End-User use only!" -Gigabyte MB manual (8I865GME-775-RH-Rev2.0)
|
||||||||||||
|
|
|
|
05-30-08
|
#147 (permalink) | |||||||||||||
|
New to Overclock.net
|
My Striker II Formula developed the Dreaded "CPU INIT" problem, I switched to a EVGA 780i Mobo. Much more stable. My question is about NVidia. What I have found that is working very well is booting in to win XP will my bios settings and useing Nvidia Performance (NTune?) inside xp to overclock. With this EVGA board I have access to pretty much everything available in BIOS. IF I try to boot from BIOZS with the same seetings I use in Nvidia I get a BSOD (Varies Page Fault, IRQ issues, others) , but if I change things in nvidia, I dont need to reboot to test the settings and ITs WAY more stable. Also I have modified my chassis some added some better fans.
__________________I have been running for the past three days at 3.315 GHz (I havent turned off yet) ( I have been up to 3.4 but I need to tweek a bit to stablize there) FSB 442 cpu core 1.381 NForce SPP Core 1.4V NForce MCP Core 1.525 FSB Voltage 1.3 HT NForce SPP <-> MCP 1.250 Memory 1.85V Do these voltages sound right? With my usual work load (Lots of CAD work, Rendering, Excel, Word, outlook, etc) MAX temps I have seen are 51C. Typical temps hover about 44. I figure if I do some ducting to direct air a bit more properly I can drop these closer to 40.
|
|||||||||||||
|
|
|
|
05-30-08
|
#148 (permalink) | |||||||||||||
|
New to Overclock.net
|
Typo, VCore 1.281
__________________
|
|||||||||||||
|
|
|
|
05-30-08
|
#149 (permalink) | ||||||||||||||
|
Folding Fanatic
|
Quote:
teK
__________________
Because an Amen a day keeps the Devil away. ~JML You can fool some people all the time, all people sometimes, but never everyone every time. I Fold, Ik vouw, Tiklop ko, Je fois, Ich falte, אני לקפל, 私は展開, 난 배, Я раз, I veces! ..::|Q9300 Club|::.. ..: Given all things probable, what is the probability something not probable will happen? ~JML :..
|
||||||||||||||
|
|
|
05-31-08
|
#150 (permalink) | |||||||||
|
New to Overclock.net
|
I have some problems with the temperature of my Q9300.
__________________ I have this system : Q9300, Artic Silver 5, Tuniq Tower 120, ex38-dq6, 2x WD 250GB, Corsair 520 HX, Gainward 9600 golden sample 512MB, 2x Mushkin 2GB (Dual Channel Kit), A+ Monolith. Which is the real temperature of my CPU in IDLE, STOCK ?  OVERCLOCK I didn't modify the voltage of the CPU.It is on "Auto". Q9300 @ 2800 Mghz, IDLE + Real Temp 2.6  Q9300 @ 2800 Mghz, STRESS + Real Temp 2.6  I don't overclock my CPU any further because I don't know the real CPU temperature. Maybe someone can help me. Why my CPU has so high temps ? I use Tuniq Tower with the fan on half power.
|
|||||||||
|
|
|
