myerz635

B04 is the latest....not sure on the exact changes over B03 but i know it adds support for 45nm. I'm at 1.48 @ 3.6
Tuniq Tower or thermalright ultra extreme

__________________

DSK DOC

or even the arctic cooling freezer 7 pro, I have my q6600 (B3) overclocked to 3.15ghz and at idle I hover around 37c

MrSpock2002

Use this Rosewill RCX-Z3 Cooler

It's worked great for me. Temps idle 34c for cores. Max load using Prime95 is about 59-60c with the torture heat test. I love it.

wuyanxu

get the Thermalright Ultra 120 Extreme cooler

overclocked at 3.2Ghz, 1.41v in the BIOS (either crappy batch or mobo's bad vdrop) and still only getting around 35c idle, max is never above 60c, around 56-58

Shadowskater

Hey guys, got my computer up and running on my new IP35pro, and I was interested in the Dual RJ45 Ethernet ports, I read somewhere that I can use them to create a small network. My router is downstairs and I am opposed to wireless so I have 1 wire running up to my room and I was interested in having two computers running up here, so I plug 1 wire from my router into my IP35pro, and then a crossover cat5e cable in the other port and plug that into another computer. I cannot get this to work though, any thoughts? thanks in advance!

ninjinsamax3

Is it possible to do SLI with this board? I have a evga 7600GT and I want to get another, so would it work with this set up?

Azazel

No sli and I don't know about the dual ethernet port thing.

__________________
X-fi digital out -> Buffalo DAC ES9008 -> Firstwatt F1 -> AKG K701(balanced stock cable)/AKG K1000/Victor HP-DX1000(balanced stock cable)

DSK DOC

I am not sure on the dual ethernet thing, though I would think that you would be able to set the second port to pass through. with that said, why not just go out and get a cheap simple "switch" I do believe they only cost 10-20 and they work rather well if you are already running a router. I would never use one without some sort of a firewall though.

here is a list of them on the egg, these start off at more than I thought but they are all gigabit so your file transfers between the computers will be fast, you could go alot cheaper "less than $10" but than you are limiting yourself to 10/100 instead of 10/100/1000
http://www.newegg.com/Product/Produc...k=&srchInDesc=

Hope that helps.

lagona

Hi, everyone..
I am new and need some help..

When I overclock my IP35 Pro w/ E2140 to 3.0 GHz (375MHz, Mem 750MHz), everything was fine. But, after I installed a new cooler (Zalman 9500AT), the temp dropped ~10C, so I decided to go for more 3.2GHz (400MHz, 800). I had to set the Vcore at 1.37 (which read 1.33 in uGuru) and memory at 2.25. Then, I did the stability test with Orthos for several hours and found the system was stable with the new voltage and clock settings. However, at some point it gave me a BSOD and then it randomly gave me the ugly screen even when I browse the web.

When I run it at a stock speed 1.6GHz (200MHz, 800FSB), it seems ok. But, when I run it at 3.0 GHz with the previous stable setting, it gave me BSOD and 3.2GHz as well. (it's not even taking 2.0GHz.) I may have fried the CPU, I am not sure.. But, what I don't understand is that the temp was very good.. In idle, it was 25C.. and fully loaded, it was ~45.. (at 3.0GHz). (at 3.2GHz, 32C idle, 55 fully loaded)

I am going to test the system tonight to find out which part is giving me trouble by swapping different system parts. But.. I need your expert opinions to guide me through this "difficult time". ^^; (I am still new to overclocking and first time with Abit board.) Any input or suggestion will be greatly appreciated and helpful.. Thanks!


Here is the spec:
Abit IP35 Pro | E2140 | Ballistix 2GB 6400 | BFG 7900GS | Barracuda 2x320GB (RAID0) | Corsair 620HX

Azazel

Make sure you have the speed step crap disabled in the bios. I forget what they are called but its 2 functions you have to disable. You will have to raise the northbridge voltage(MCH in bios) and probably use a divider lower than x2 on the ram also(to keep it around stock speed). 2.25 volts for the ram seems a little high to me. You could try 2.0 or 2.1 for the ram. What are your mosfet temps(pwm in uguru) after a long prime95 session? A few of us with the IP35 have reseated the mosfet cooler to make sure it had good contact.

Feel free to send me a message on here if you really need help. I can jump on aim or yahoo messenger if you need more help so we don't have to watch this thread all the time.

__________________
X-fi digital out -> Buffalo DAC ES9008 -> Firstwatt F1 -> AKG K701(balanced stock cable)/AKG K1000/Victor HP-DX1000(balanced stock cable)