DFI Lanparty DK P35-T2RS Thread

[Bal3Wolf]

Id probly lean towards psu because if the boards working at stock probly not bad but its a toss up. The gpu and cpu are probly on same rail inside of the psu you might try to put a old gpu in that requires less amps i know the x1950 cards are power hungery cards.

[thomasbu]

It might, although the 12V2 rail is supposed to be just for the CPU and the 12V1 (20A) for the rest. At home right now im running Prime95 , started it this morning and wont get home till about 7 so I will see if its failed. What I guess I could try doing is taking my 580 Hyper PSU and use that just for the 6 PIN GPU or for mobo connections and see where that takes me. i had posted another thread asking if all that stuff is fine with my PSU and i had 2 yes's saying deff. so.... I guess people cant always be right. Thanks for your help man, will post back later

With the GPU at its current clocks, I ran 3D mark 06 succesfully, with a fairly good score, and the 12V rails went down to...i think....11.85? or somewhere in that range with the DMM. I put my cold cathodes on Flash rather then steady on and that seemed to take a bit of load off the PSU. Brought 12V from 11.97 to 12.00~11.99. Didnt realize they had such a big load. If worse comes to worse, I can take internal components like Pump + Cathodes and run them off an external PSU. There goes the electricity bill (:

BTW- Odd thing it says, and one of the reasons I get it, it was SLI compatible so thought it would have no problem running a single card. Go figure.

[brozi]

Hey guys,

DK P35-T2RS
Intel Q6700
Crucial Ballistixs 2GB DDR2-800 4-4-4-12
Noctua NH-P12U Cooler

I played with the BIOS a little but I cant seem to achieve a decent overclock. Can anyone recommend BIOS settings I should be using.

As of now I am currently clocked @ 3.2ghz (400FSB x 8 multiplier). Which seems to be the highest I can get.

Has anyone else had experience with this ram or CPU with this board.

[wigseryc]

Originally Posted by Romwin

Ok, I seem to have hit a wall. I am hoping that the pro's here may be able to help me a bit. I have a stable OC of 3.2 for 10 hours on Prime95. The problem I seem to be running into is that I can't get it any higher. This is fine, but it seems like my Vcore is set extremely high for only reaching 3.2. These are my specs:

DFI LP UT P35-T2RS (03/11/2008 BIOS)

PROC - Q6600 GO stepping
MOBO - DFI LanParty Dark P35-T2RS Socket 775 Motherboard
PSU - Corsair 520HX Modular ATX Power Supply
RAM - CORSAIR XMS2 4GB (2 x 2GB) TWIN2X2048-6400C4DHX
GPU - MSI GeForce 8800GTX
HDD - Seagate Barracuda 7200.10 250GB HDD
HS - Thermalright XP-120 Heatsink with the LGA775 Retention Mechanism
HSFan - Scythe S-FLEX™ SFF21F - 120mm 1600 rpm Quiet Fan

Genie BIOS Setting:

Exit Setup shutdown........................ - Mode 2
Shutdown after AC Loss .................. - Disabled
OC Fail Retry Counter...................... - 0
CLOCK VCO divider.......................... - Auto
CPU Clock Ratio.............................. - 8 X
- Target CPU Clock.......................... - 3200 MHz
CPU Clock...................................... - 400 MHz
Boot Up Clock................................. - Auto
DRAM Speed................................... - 333/667
- Target DRAM Speed....................... - DDR2 801
PCIE Clock..................................... - 100 MHz

CPU Spread Spectrum....................... - Disabled
PCIE Spread Spectrum...................... - Disabled
SATA Spread Spectrum...................... - Disabled


CPU Feature:

Thermal Management Control................ - Disabled
PPM(EIST) Mode................................ - Disabled
Limit CPUID MaxVal............................. - Disabled
C1E Function..................................... - Disabled
Execute Disable Bit............................. - Disabled
Virtualization Technology..................... - Disabled
Core Multi-Processing.......................... - Enabled


Voltage Setting:

CPU VID Special Add....................... - +150.0 OmV
DRAM Voltage Control...................... - 2.100 V
SB 1.05V Voltage............................- 1.070 V
SB Core/CPU PLL Voltage................. - 1.55V
NB Core Voltage............................. - 1.41V
CPU VTT Voltage............................ - 1.2V
Clockgen Voltage Control................. - 3.45V
CPU GTL 1/3  REF Volt..................... - 67
CPU GTL 0/2  REF Volt..................... - 67
North Bridge GTL REF Volt................ - 67


DRAM Timing:

Enhance Data transmitting............... - Fast
Enhance Addressing........................ - Fast
T2 Dispatch.................................. - Auto

CAS Latency Time (tCL)....................... - 4
RAS# to CAS# Delay (tRCD)................. - 4
RAS# Precharge (tRP).......................... - 4
Precharge delay (tRAS)....................... - 12
All Precharge to ACT........................... - AUTO
REF to ACT Delay (tRFC)..................... - AUTO
Preformance LVL (Read delay).............. - AUTO

MCH ODT Latencey.......................... - AUTO
Write to PRE Delay (tWR).................. - AUTO
Rank Write to Read (tWTR)................. - AUTO
ACT to ACT Delay (tRRD)................... - AUTO
Read to Write Delay (tRDWR)............... - AUTO
Ranks Write to Write (tWRWR).............. - AUTO
Ranks Read to Read (tRDRD)................ - AUTO
Ranks Write to Read (tWRRD)............... - AUTO
Read CAS# Precharge (tRTP)................ - AUTO
All PRE to Refresh........................ - AUTO


Clock Setting Fine Delay:

Ch1 Clock Crossing Setting................ - AUTO
DIMM 1 Clock fine delay................... - Current[1424]
DIMM 2 Clock fine delay................... - Current[ 574]
Ch1 Command fine delay.................... - Current[974]
Ch1 Control fine delay.................... - Current[ 512]

Ch2 Clock Crossing Setting................ - AUTO
DIMM 3 Clock fine delay................... - Current[1300]
DIMM 4 Clock fine delay................... - Current[486]
Ch2 Command fine delay.................... - Current[1024]
Ch2 Control fine delay.................... - Current[ 400]

Ch1Ch2 CommonClock Setting................ - AUTO

Ch1 RDCAS GNT-Chip Delay.................. - Auto
Ch1 WRCAS GNT-Chip Delay.................. - Auto
Ch1 Command to CS Delay................... - Auto

Ch2 RDCAS GNT-Chip Delay.................. - Auto
Ch2 WRCAS GNT-Chip Delay.................. - Auto
Ch2 Command to CS Delay................... - Auto


Read delay phase adjust:

Channel 1 Phase 0 Pull-In................. - Auto
Channel 1 Phase 1 Pull-In................. - Auto
Channel 1 Phase 2 Pull-In................. - Auto
Channel 1 Phase 3 Pull-In................. - Auto
Channel 1 Phase 4 Pull-In................. - Auto

Channel 2 Phase 0 Pull-In................. - Auto
Channel 2 Phase 1 Pull-In................. - Auto
Channel 2 Phase 2 Pull-In................. - Auto
Channel 2 Phase 3 Pull-In................. - Auto
Channel 2 Phase 4 Pull-In................. - Auto

With these settings my Vcore is 1.45 (I have performed the VDroop mod) and VDroop goes to 1.42 at load. It seems most people can hit 3.2 without even changing the Vcore but as you can see mine is set pretty high. Does anyone have any ideas of what else I can try? If i drop the settings for the CPU voltage by one I am unstable in Prime95.

Thanks
Rom

Try these out from page 35.. They were alright for me and my E6600..

[brozi]

Those settings seem to work fine. I am @ 3.2 right now. I really want to try and use a multi of 9. I was also hoping I'd be able to get something around 3.6 or so.

But I cant get over 3.2

[Bal3Wolf]

Originally Posted by thomasbu

It might, although the 12V2 rail is supposed to be just for the CPU and the 12V1 (20A) for the rest. At home right now im running Prime95 , started it this morning and wont get home till about 7 so I will see if its failed. What I guess I could try doing is taking my 580 Hyper PSU and use that just for the 6 PIN GPU or for mobo connections and see where that takes me. i had posted another thread asking if all that stuff is fine with my PSU and i had 2 yes's saying deff. so.... I guess people cant always be right. Thanks for your help man, will post back later

With the GPU at its current clocks, I ran 3D mark 06 succesfully, with a fairly good score, and the 12V rails went down to...i think....11.85? or somewhere in that range with the DMM. I put my cold cathodes on Flash rather then steady on and that seemed to take a bit of load off the PSU. Brought 12V from 11.97 to 12.00~11.99. Didnt realize they had such a big load. If worse comes to worse, I can take internal components like Pump + Cathodes and run them off an external PSU. There goes the electricity bill (:

BTW- Odd thing it says, and one of the reasons I get it, it was SLI compatible so thought it would have no problem running a single card. Go figure.

Ya but from some reviews i read on differt psu the pcie connector and cpu connectors are all on same rail im not sure if its same with your psu or not.

[BTK]

this isnt the DK but .....

http://www.newegg.com/product/produc...82E16813136039

[thomasbu]

Right

[thomasbu]

Originally Posted by Bal3Wolf

Ya but from some reviews i read on differt psu the pcie connector and cpu connectors are all on same rail im not sure if its same with your psu or not.

Oh i see. Well i ran Prime95, in windows safemode, dual threads last night for 11 hours and no errors. The only thing I did was turn off my cold cathodes (6 of them) and the 12V went to 12.02 stable. So maybe that was the trick. I just clocked it up to 2960 and am running the DOS PRIME 95 and will see where that takes me.

Edit- I take another PSU and run the GPU and a majority of my fans off of it and still could not boot at 3000MHZ. SO I dont think its a PSU problem. Although when i took all that stuff off the 12V went from 12.02 to 12.08 but nothing really important. I also upped the SB/CPU Pull Voltage to 1.75 and now it seems @ 2960MHZ, prime 95 has been running for an hour so.... Ohhh well, Im at a lost here.

[Bal3Wolf]

Ya you got a wierd issue maybe rma the board to newegg while you got time so you will have a faster rma.