Asus P5N-D 750i Guide - Page 3 - Overclock.net

go4life · 04-18-08

Quote:

Originally Posted by JLewis187

and Go4Life please take that rifle man and go hunting or something...

Will do

JLewis187 · 04-30-08

lordikon yo man please supply me with what your Voltage settings are for HT, NB, SB .. Please bro thanks.

bitmonx · 05-02-08

Hey this is my first OC and need help.

I set the BIOS as per Sticky for Overclocking P5N-E.
After saving and rebooting I got a constant beep. In my mobo manual there is no list of what beeps are what so I looked it up on the nety and it told me that it is the RAM. So I ran a MEMtest for about an hour with no errors.
I have 2 sticks of Crucial Ballistix DDR2 800. I set the timings to 4-4-4-12-T2. Is that correct? What other different bios settings do I need to set different that for the P5N-E?
I use the P5N-D with a E8400 and 2x 1GB Crucial Ballistix DDR2 800. I had to set the timings to 5-5-5-12 and Auto otherwise I got a continues beep at POST.
The higest I got was FSB 1450, DDR 820, VCore 1.40, NB 1.68, SB 1.62, HT 1.68, DDR 2.11.
My core temp was very high at these settings but ran for 30 minutes without errors and I stopped the test. The core temp was 70 deg. C!!!! I tried to lower the VCore to 1.38 but after 2 min. with Prime95 I got a blue screen.
Is my CPU faulty or could it be that there was too much thermal compound, I believe Arctic Freezer comes with MX-1 already applied). The core temp at idle is 49 deg. C.
What can I do?

ljapilot · 05-02-08

I used JLewis187 settings from page 2 and I couldnt go to 3.2 I tried raising all the values at least by a few. I went from it telling me it wont post to getting to the windows screen before she crashed. Then I gave up hehehe.

I am running BIOS 0302 would that make a difference?

I am new to overclocking as you can tell I am sure. What does the HT voltage control??

Thanks

go4life · 05-02-08

Quote:

Originally Posted by bitmonx

Hey this is my first OC and need help.

I set the BIOS as per Sticky for Overclocking P5N-E.
After saving and rebooting I got a constant beep. In my mobo manual there is no list of what beeps are what so I looked it up on the nety and it told me that it is the RAM. So I ran a MEMtest for about an hour with no errors.
I have 2 sticks of Crucial Ballistix DDR2 800. I set the timings to 4-4-4-12-T2. Is that correct? What other different bios settings do I need to set different that for the P5N-E?
I use the P5N-D with a E8400 and 2x 1GB Crucial Ballistix DDR2 800. I had to set the timings to 5-5-5-12 and Auto otherwise I got a continues beep at POST.
The higest I got was FSB 1450, DDR 820, VCore 1.40, NB 1.68, SB 1.62, HT 1.68, DDR 2.11.
My core temp was very high at these settings but ran for 30 minutes without errors and I stopped the test. The core temp was 70 deg. C!!!! I tried to lower the VCore to 1.38 but after 2 min. with Prime95 I got a blue screen.
Is my CPU faulty or could it be that there was too much thermal compound, I believe Arctic Freezer comes with MX-1 already applied). The core temp at idle is 49 deg. C.
What can I do?

Hi

Try to lower the NB & SB to 1.56 and HT 1.52.. that is what i run at

From what ive heard people using the E8400 use 1.4vcore to get 4ghz if I dont remember wrong! Try to leave your ram all at stock when you oc the cpu, then you take the ram and oc it

The temp problem.. hmm... do you have any fans in your case?

go4life · 05-02-08

Quote:

Originally Posted by ljapilot

I used JLewis187 settings from page 2 and I couldnt go to 3.2 I tried raising all the values at least by a few. I went from it telling me it wont post to getting to the windows screen before she crashed. Then I gave up hehehe.

I am running BIOS 0302 would that make a difference?

I am new to overclocking as you can tell I am sure. What does the HT voltage control??

Thanks

yo

try updating the bios (0402), I do not know what the HT does!:/ my system got more stable with a little bit more volt than Jlew had, but thats a little different

bitmonx · 05-02-08

I have a stocj Coolermaster Centurion which has a front fan (80mm) sucking air in and a back fan (120mm) blowing air out. I as thinking about installing another 120mm fan on the sidepanel to get more air into the case.
As for the CPU, I need to order some MX-2 and lapp the CPU and HS. Hopefully that will do the trick.
My GPU is running also quite hot at 70 deg. C. when playing COD4 after about an hour just running the desktop my GPU sits at 61 deg. C.
There was quite a lot of thermal paste on the HS do you think that may be the problem? I could install the stock HS and see what the difference is. Today it is a bit cooler in my room and the CPU core temp is now 45 deg. C. I don't know what the room temp is.....I would guess around 20 deg. C. Does the thermal paste need to be run in as well and how much time is that?
I just tried to set the voltages as recommended and something weired is going on. When I set the AI overclock to manual, it will post and go into windows but when I restart and go into bios the settings have changed back to auto. When I again select Manual and set the FSB and voltages as I have set before that were working, there is no increase in FSb in Core Temp (program) and shows me having 3000 mhz (333x9). What is going on now?

Yesterday I tried the AI overclock of 20% but it would not post. I tried again now and 20% oc works. I am running it now with Prime95 and the core temp is at 63 deg. C.

go4life · 05-02-08

Quote:

Originally Posted by bitmonx

I have a stocj Coolermaster Centurion which has a front fan (80mm) sucking air in and a back fan (120mm) blowing air out. I as thinking about installing another 120mm fan on the sidepanel to get more air into the case.
As for the CPU, I need to order some MX-2 and lapp the CPU and HS. Hopefully that will do the trick.
My GPU is running also quite hot at 70 deg. C. when playing COD4 after about an hour just running the desktop my GPU sits at 61 deg. C.
There was quite a lot of thermal paste on the HS do you think that may be the problem? I could install the stock HS and see what the difference is. Today it is a bit cooler in my room and the CPU core temp is now 45 deg. C. I don't know what the room temp is.....I would guess around 20 deg. C. Does the thermal paste need to be run in as well and how much time is that?
I just tried to set the voltages as recommended and something weired is going on. When I set the AI overclock to manual, it will post and go into windows but when I restart and go into bios the settings have changed back to auto. When I again select Manual and set the FSB and voltages as I have set before that were working, there is no increase in FSb in Core Temp (program) and shows me having 3000 mhz (333x9). What is going on now?

Yesterday I tried the AI overclock of 20% but it would not post. I tried again now and 20% oc works. I am running it now with Prime95 and the core temp is at 63 deg. C.

You ONLY need a little thermalpaste! Too much will cook your cpu! get a thin thin layer all over the cpu.. They usualy say it needs 48 hours to get the themalpaste to be good

NEVER USE THE AI OVERCLOCK!!!!!!!! Heard of someone that actually fried his cpu because of that! only manual is aloud

bitmonx · 05-02-08

Well, I was trying to use manual OC but the bios always revert back to Auto.
What am I doing wrong here? What could be the reason for that?
HEEEEEEEEEEEEELLPPPP!!!!!!!!! Please......

Hey go4life would you happen to have a few minutes to go on messenger......?

GaminProject · 05-02-08

go4life i need your help bad!!!!!!!!!!!!!
thanx

04-30-08	#22 (permalink)
JLewis187 New to Overclock.net Join Date: Apr 2008 Posts: 25 Rep: 2 Unique Rep: 2 Trader Rating: 0	lordikon lordikon yo man please supply me with what your Voltage settings are for HT, NB, SB .. Please bro thanks.

		Overclock.net - Overclocking.net > Intel > Intel Motherboards
Asus P5N-D 750i Guide

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)