Ghostleader

Yeah sure there´s something wrong, to much settings on auto, you should set the following manual.

FSB Frequency: 400, if DET DRAM, lower it to 350 and work your way up by 5
CPU Ratio Setting: 7,5
CPU Clock Skew: Normal (or Delay 100ps)
NB Clock Skew: Normal
FSB Strap to North Bridge: 200
PCIE Frequency: 100
DRAM Frequency: 1600Mhz
DRAM Command Rate: 2N

DRAM Timing Control : Manual
CAS# Latency: 8
RAS# to CAS# 8
RAS# Pre Time: 8
RAS# ACT Time: 24

Rest of the timing is on auto

DRAM Static Read Control: disabled
DRAM Dynamic Write Control: disabled

DRAM Skew Control is all on auto

Ai Clock Twister: Moderate
Ai Transaction Booster: Manual

Common Performance Level: 7
All Pull-Ins are disabled

EPU II Phase Control: Auto
CPU Voltage: 1,285 - 1,325 (can lower it later on)
Load-Line Calibration: Enabled
CPU PLL Voltage: 1.55
FSB Termination Voltage: 1.30
CPU GTLVerf (0): AUTO
CPU GTLVerf (1): -40
CPU GTLVerf (2): AUTO
CPU GTLVerf (3): -40
NB GTLVerf: +60
North Bridge Voltage: 1.40 - 1.45
DRAM Voltage: 1,90
NB DDRVref: AUTO
DDR3 ChannelA Vref: AUTO
DDR3 ChannelB Vref: AUTO
South Bridge 1.5 Voltage: 1.51
South Bridge 1.05 Voltage: 1.06
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

BTW, those temp on CPU, NB and SB are way to high, probably because you run volt value on auto and when you only change FSB manual to 400 the board automaticly raise the volt and try to run that OC and the volt value get to high, so better set then manually.

Set the above and try and post pic of all settings in the Extreme Tweaker tab, please.

__________________

Asus Rampage Extreme Overclocking Guide

Running SLI on a Rampage Formula

Running SLI on a Rampage Extreme

Test Rig

$SpEEdFreAk$

That's a pain looking at those pics like that. All I saw was the expected high temps, NB no exception.
Not enough other info to go on...

__________________

Kavourdoukos

Haha this is what i got.Now i will try to lower the fsb and make the changes listed above.

Kavourdoukos

I made the changes and now my pc openen at 350 fsb.I will start lvl-ing up.

Ghostleader

Great, now we talking, shouldn´t be any problem to reach 400, so keep it coming.

__________________

Asus Rampage Extreme Overclocking Guide

Running SLI on a Rampage Formula

Running SLI on a Rampage Extreme

Test Rig

Kavourdoukos

Haha something really strange happens here!!I reached fsb at 399 but no 400.Lol?Also i got 1 blue screen from windows.get some photos of the bios settings.
http://img208.imageshack.us/gal.php?g=img0062fku.jpg

Ghostleader

Very good mate, you´re close.

You run Crossfire with those 4870, hmmm

Probably you need more North Bridge Voltage and also FSB Termination Voltage, raise both by three steps each (when they are highlighted you can use - key to lower and + key to raise).

Also try to ad some cooling for your NB because it´s to hot to be comfortable with.

__________________

Asus Rampage Extreme Overclocking Guide

Running SLI on a Rampage Formula

Running SLI on a Rampage Extreme

Test Rig

Kavourdoukos

Can u find a cooler for my nb pls?I am running a memtest now to check stability.

Ghostleader

Do you run @ 400 and do a memtest, which memtest?

Have you these mounted?



You should consider to replace the thermal paste beween the NB and the heatsink, it might lower your temp by 5 - 10C, I know, it´s a real pain to do it when all is mounted, therefore I always do it before I mount the board into the case.

__________________

Asus Rampage Extreme Overclocking Guide

Running SLI on a Rampage Formula

Running SLI on a Rampage Extreme

Test Rig

Kavourdoukos

I got some more blue screens from windows ..I dont have theese coolers mounted.BTW i dont know why the shop that installed my pc didnt installed them and kept them boxed.I have theese coolers.Do u have a picture of where to install them?