DOM.

yeah i know but if you dont got the right CPU/MCH Reference it wont oc for crap i got diff ones for my dual core
try uping your CPU Termination to 1.36 and your CPU/MCH Reference should be at .901

try vcore at 1.45 should be like 1.4-1.45v in windows

KaRLiToS

SO where do I start, I have to raise the FSB First without anyother changes (except for the stock memory voltage) then what should I do.

__________________

RePuBLiC oF KaRLiToS (Build Pictures)

Water Loop
-Feser 360 and 240
-Dual MCP 655 Pumps With dual top
-HeatKiller 3.0 CPU
-EK FC 5850 Acrylic GPUx2
-EK RE3 Full water Block


Reservoir --> Dual MCP 655 --> 360 Rad --> CPU --> MOBO --> 240 Rad --> GPU-GPU--> Back To Reservoir

dennyb

Here is a good place for info on how to overclock Intel processors. If everyone reads this and some of the overclocking stickies they will have a leg up and will be able to make progress on their own.

We are here to help,but it would be helpful to us if folks did some of their own research as well. Not trying to be rude,just practical

http://www.overclock.net/intel-cpus/...-core-2-a.html

and here
http://www.overclock.net/intel-cpus/...ed-guides.html

__________________

marsey99

this is a good, easy to understand guide for those starting out ocing too

shame its not on Overclock.net tbh but still its good.

__________________

10acjed

Well some things I do understand that I had a tough time finding are general reference of voltage settings...

Telling someone to up this or that voltage without giving them a general idea of what range is safe isnt always helpful... I'd just hate to see someone throwing 1.45 CPU Term to there 45nm cpu not realizing it is unsafe even if the cpu voltage is below 1.36.....

For a 45nm Q the CPU Term and MCH should be pretty close regardless of chip.. Same goes with 65nm Q.....

Trial and error will allow you to find your minimum voltage for each system, and will be different. But I doubt one guy need 1.45 CPU Term and another needs 1.2 to reach the same FSB on the same cpu....

From what I have gathered it seems 1.3 is the averege for a CPU Term on a 45nm Q, and 1.28 - 1.30 MCH

__________________

marsey99

you wont find many people telling anyone to run 1.36vcore with term at 1.45v in here m8

tbh i think only a handful of us have pushed their chips so high that we have needed near that amount never mind telling others to do it.

__________________

NoGuru

If you got some info for me to add let me know. Keep in mind this is just the basics to get started. http://www.overclock.net/intel-mothe...-ep45-ud3.html

__________________

Join Overclock.nets
HWbot team here!

MADMAX22

Maybe you could find that pic of the voltage table results on ET6 for the variouse settings in bios. I think I saw it at xs if I had it saved I would post it.

Would be pretty good for that thread I think.

__________________
E6400@3856E4300@4158E6600@4510,Opti148@3102,opti170@2918,UD3P&9550@4692
UD3P&84005304,UD3p&85005567

NoGuru

Thanks MM,Let me know if you find it.
Also I am looking for the MCH Frequency Latch table if anyone has it.

__________________

Join Overclock.nets
HWbot team here!

Dilyn

Excellent page mate


I do believe Denny has that table you're looking for. I've seen it posted in here before, anyways.

__________________