valtopps

anything you see im doing wrong please let me know. oc 3.6ghz. if i try 3.8ghz with 1.4v blue screen? im using f6 bios.



******Motherboard Intelligent Tweaker (M.I.T.)******
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 8 ]
Fine CPU Clock Ratio............................[ + 0.5 ]
CPU Frequency 4.0GHz............................[ 424 x 8.5 ]
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 424 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2 [Disabled]

******Advanced Clock Control******
CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[ 900mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]

******DRAM Performance Control******
Performance Enhance.............................[Standard]
(G) MCH Frequency Latch.........................[ auto]
System Memory Multipler.........................[ 2.00B]
Memory Frequency 800............................[ 848]
DRAM Timing Selectable..........................[ Manual]
CAS Latency Time................................[ 5]
tRCD............................................[ 5]
tRP.............................................[ 5]
tRAS............................................[ 15 ]

******Advanced Timing Control******
tRRD............................................[ Auto ]
tWTR............................................[ Auto ]
tWR.............................................[ Auto ]
tRFC............................................[ Auto ]
tRTP............................................[ Auto ]
Command Rate (cmd)..............................[ Auto ]

******Channel A Timing Settings******
Static tRead Value [ 10 ] ...............[ 9 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel A Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Channel B Timing Settings******
Static tRead Value [ 10 ] ...............[ 9 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel B Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Motherboard Voltage Control******
Load-Line Calibration...........................[ disabled ]
CPU Vcore [ 1.21250 ]...................[ 1.3625 ]
CPU Termination [ 1.20 ]...................[ 1.28 ]
CPU PLL [ 1.50 ]...................[ 1.59]
CPU Reference [ 0.760 ]...................[ 0.863 ]
MCH Core [ 1.100 ]...................[ 1.36]
MCH Reference [ 0.760 ]...................[ 0.850 ]
MCH/DRAM Refernce [ 0.900 ]...................[Auto ]
ICH I/O [ 1.500 ]...................[ 1.59]
ICH Core [ 1.100 ]...................[ 1.20]
DRAM Voltage [ 1.800 ]...................[ 2.10]
DRAM Termination [ 0.900 ]...................[Auto]
Channel A Ref [ 0.900 ]...................[ Auto]
Channel B Ref [ 0.900 ]...................[Auto]

__________________
HERE I IS


E5200 3.6GHZ********** E8600 4.4GHZ ***********Q9650 4GHZ
E7200 3.8GHZ********** Q9450 3.4GHZ
E8400 3.8GHZ********** Q9550 3.8GHZ

Robilar

With vdroop in effect (as you have LLC disabled), you will need more vcore than 1.3625 in the bios. that will only net out to about 1.31 under load.

InTeL

voltopps please change these settings, i hope you can make it stable good luck man
System Memory Multipler.........................[ 2.00D]
Load-Line Calibration...........................[ Enabled ]

Robilar

He's using a 45nm quad. LLC is not advisible.

InTeL

mine is enabled, just disable all those craps in bios C1E / Speedstep

CL3P20

I always recommend setting the MCH boot strap manually to 333mhz when using FSB in excess of 400mhz.. even though it seems these mobo's do a very good job with auto MCH settings anyhow

@ valtops- have you tried that same FSB without the .5 multi yet? Also..your MCHv ref, doesnt really need to be that high for ~420mhz... with a similar CPU and RAM, I found I only needed .82v for 465mhz FSB and 1100+mhz RAM speeds.

*the 2x UD3P mobo's I 'built' were also giving me BSOD, when MCHv ref was too high.. lowering it fixed my issues on both systems.

__________________

..:Q6600 Club:..

INTEL 45

e8400: 5.13ghz
e7400: 4.5ghz
Q6600: 4.44ghz
8800GS@1028mhz
My photo albums

valtopps

ok ill try 2.00D but im not sure about load line. thanks

well i tried to put it to 2.00D AND COULDNT FIND IT THE ONLY option is 2.00B

__________________
HERE I IS


E5200 3.6GHZ********** E8600 4.4GHZ ***********Q9650 4GHZ
E7200 3.8GHZ********** Q9450 3.4GHZ
E8400 3.8GHZ********** Q9550 3.8GHZ

valtopps

ok ill try manually set boot strap 333mhz and low mch ref to .820, thanks


when i didnt use the .5 mult and raised the fsb it wouldnt even boot. it seems to work better with lower fsb.


should i use the load line ? i realy want to hit 3.8ghz and like i said before i tried it with 1.4v?

__________________
HERE I IS


E5200 3.6GHZ********** E8600 4.4GHZ ***********Q9650 4GHZ
E7200 3.8GHZ********** Q9450 3.4GHZ
E8400 3.8GHZ********** Q9550 3.8GHZ

lsdmeasap

That is only becuase you have MCH Latch set to 333. To use 2.00D you have to put MCH latch on Auto or 400 and then you will see it.

Here is all the straps/multi's. If you have MCH Latch on Auto, you will see them all, otherwise if you set MCH Latch you will only see the Multi's for that strap >>>

__________________

Enyalius

With a 45nm processor, LLC can do some serious damage (though, there are no guarantees). If you really want to get up to 3.8GHz, given your current settings, I would think that you are going to have to water cool and have a vCore somewhere around 1.5v (just an estimation).

__________________
I did error10's Windows Challenge and I now have lost two IQ points!