|
|
|
#1211 (permalink) | |||||||||||||
|
4.0 GHz
![]() |
Mines is 1.2625V, also Cpu speed>ram speed. Just try higher fsb and you don't have to run your ram at 1:1 ratio with fsb.
__________________
|
|||||||||||||
|
|
|
|
|
#1212 (permalink) | ||||||||||||
|
FireFighter.
![]() |
Well im at 3.6ghz right now. What else should I try? Im open to all suggestions.
__________________
The AM3 motherboard buyers guide and help thread. Member of the OCN Diablo III Club Thank you veterans.
|
||||||||||||
|
|
|
|
#1213 (permalink) | ||||||||||||
|
The Dark Passenger
![]() |
using different ratios will run your ram at higher speeds in relation to your cpu fsb. As mentioned above, 2b is 1:1, try the other settings in the bios.
__________________just so you understand, higher mhz on ram with looser timings is about the same as lower mhz with tighter timings. ram overclocking serves very little benefit in general benchmarks.
|
||||||||||||
|
|
|
|
#1214 (permalink) | ||||||||||||
|
FireFighter.
![]() |
so I can run 1.1 ram ratio at DDR2-800 4-4-4-12 timings and that would be good? I just PC game thats really it.
__________________
The AM3 motherboard buyers guide and help thread. Member of the OCN Diablo III Club Thank you veterans.
|
||||||||||||
|
|
|
|
#1215 (permalink) | ||||||||||||
|
4.0ghz
![]() |
yea that would be fine
|
||||||||||||
|
|
|
|
#1216 (permalink) | ||||||||||||
|
FireFighter.
![]() |
I just want to make sure I dont have a borked ass UD3. I see these boards doing 500+ fsb and mine only does 400? WTH?
__________________
The AM3 motherboard buyers guide and help thread. Member of the OCN Diablo III Club Thank you veterans.
|
||||||||||||
|
|
|
|
#1217 (permalink) | |||||||||||||
|
4.0ghz
![]() |
It's the Q6600, not your board. It doesn't like very high FSB. Though, ironically, mine was more stable at 450x8 than at 400x9.
__________________
The Ice Stone has melted! I did error10's Windows Challenge and I now am an MCSE: Minesweeper Consultant and Solitaire Expert! ![]()
|
|||||||||||||
|
|
|
|
#1218 (permalink) | ||||||||||||
|
"Directive"
![]() |
I would say the board handles very high FSB with a quad with very low NB voltage.
Here's 500 FSB with 1.3v on the NB and 1.36 through the processor. http://valid.canardpc.com/show_oc.php?id=491381
__________________
Intel:MainRig i7 920@4.62 1.39v/BloodRage/6GB DDR3@2000/HD4870X2 Intel:Secondary E7400@4.0 1.25v/DX38BT/4GB DDR3@1333/2XHD3870 AMD:HTPC 2400-BE/A7GM-S 2.0/2GB DDR2@855/HDMI *******Current Project: WallHanger Build*******
|
||||||||||||
|
|
|
|
#1219 (permalink) | ||||||||||||
|
The Dark Passenger
![]() |
Here is my Q9650 running orthos.
It remains to be seen if it will pass an hour at vcore this low but holy smokes! Just to clarify as well, the only settings that are off auto (for now) is vcore and ram voltage, LLC disabled as well.
|
||||||||||||
|
|
|
|
#1220 (permalink) | |||||||||||||
|
WaterCooler
![]() |
That's pretty sick stuff, Rob!
|
|||||||||||||
|
|
|
![]() |
| Tags |
| ep45-ud3p, gigabyte, ud3r |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|