PR1M3R

I plan on using LLC with my E8400 after a couple e-mails with Gigabyte. Basically they could not "admit" to having had a problem or fixing it, but he said "Some people have had similar problems for whatever reason, but NOW you should be able to use it without any problems"

So basically, they have made some kind of changes or something to remedy this problem, and just can't really say for some reason. At least thats what I got from the whole conversation.

__________________

Celeron D 352 @ 6167.77mhz

jchapman805

i have my cpu @ 333fsb idling at 45 40 45 41 degree celcius. and when i close a really intense program i get this solid freeze then you here the system beep if u do to much then it will catch up im wondering if its better to have my northbridge fan sucking air out or blowing air onto the northbridge

__________________
http://valid.canardpc.com/cache/banner/502739.png
http://img.photobucket.com/albums/v2...f5717f3b74.gif

InTeL

i dont have any problem having llc enabled for my q9550, but is it overclocking putting ur cpu at risk already

Robilar

LLC and overclocking do not pose the same risks to processors.

LLC has the biggest potential to damage a chip at idle, not load.

PR1M3R

For those that did not see my post: I have talked to Gigabyte regarding the problems with LLC damaging chips.

I plan on using LLC with my E8400 after a couple e-mails with Gigabyte. Basically they could not "admit" to having had a problem or fixing it, but he said "Some people have had similar problems for whatever reason, but NOW you should be able to use it without any problems"

So basically, they have made some kind of changes or something to remedy this problem, and just can't really say for some reason. At least thats what I got from the whole conversation.

__________________

Celeron D 352 @ 6167.77mhz

Mulingko

Hey guys, not trying to hi-jack the thread but I have a problem with my board I beleive, and was wondering if you guys or anyone else could help make sure its the board and not a setting.

I built this rig like 2 days ago, updated the bios to F7. And started clocking it up. Got her up to 3.8ghz with a lower FSB. And then got it up to like 3.7 with a FSB around 500. Anyways, everything seem to go with ease until today.

Twice now, I made some changes, went into windows and ran 3DMark06 and completed that, rebooted. It rebooted again, didnt post, rebooted istelf again (as if the voltage was wrong or something) and then when it did post, it reverted everything in my bios back to default, EVERYTHING.

I thought maybe I maxed it out or something eventhough Ive read people hitting 4.0ghz. But it did it again when I was at 3.5ghz. Seemed to be fairly stable without extensive testing... but still defaulted everything.

So I cant find anyone else with this prob... make any sense to you guys?

isune

after all the problems i have been getting, it's not a bad stick of ram.
It ended up being the board was faulty.
i made an exchange with micro center and bought a new ram, but i decided to use the G.skills ram again to test it, and it worked perfectly. So i'm at 4.0Ghz with 890Mhz stable now. =]

__________________


My 4.264Ghz

Nelson2011

My UD3P came in today and barely got home at 8PM

__________________

Windows 7║Fan Club

TFL Replica

What bios and board revision was the replacement compared to the initial "faulty" board.

__________________

le604

I got my UD3P today and wow the bios is a big change for me from the Asus P5B. Anyways I was wondering if anyone is willing to help me out here i'm just try to get to my old speeds or improve. E6300@2.8ghz 1.2875v 400fsb, 5-5-5-15 timings 800mhz. What's the latest or best bios version for this mobo atm?