Gigabyte EP45-UD3P Owners Guide - Page 502 - Overclock.net

afzsom · 08-03-09

Page 500? This is only page 126! :P

crashdummy35 · 08-03-09

Quote:

Originally Posted by supaspoon

Thanks guys.

I still have my ud3p setup though. It's going to be put on renderslave duty w/ the 9650 as soon as I get another case to put it in. Prob. going to be on air now though. Not going to get another pump/res/rad unless the missus decides she want to steal it.

The i7's pretty nice so far. In terms of general use it still kinda feels all the same. But it speeds up my rendering times something aweful, about 25%-30% gain over the 9650. Runs hot as hell though. Can tell my rad is working it's butt off as now the rig doubles as a space heater. Once again temps have reclaimed the 'limitation' throne from vcore.

That's what I'm talking about. Even though my Vegas work is extremely amature-ish, C2D's are severely lacking in this department. Even at 3.9GHz my render time on a heavily effects laden video (Pro Titler, pip, Particle Illusion) is pretty slow.

Hopefully I'll be out of the poor house in a few months and can at least grab a Q9550.

@dennyb. I see you are slowly climbing that mountain. 4.5 is almost in sight for you by now. Good luck.

dennyb · 08-03-09

I scrapped my 4.25 fft- no LLC clock and am now 1:12 into 4.25 blend LLC--Max Temps 71/69/65/65

edit 1.376v CPUZ

How have you guys been saving your overclock documents? I have been putting mine into a PM to myself and then into a folder. I also e-mail them to myself and store them in a yahoo mail folder. That way if I lose the OS I still have all of my documents stored in two places. So, how do you guys go about it?

afzsom · 08-03-09

Two hard drives. One for data (like OC information) and one strictly for the OS and programs. Formatting the OS doesn't nullify your data.

NoGuru · 08-03-09

I hand write my stuff down so I can change it on the fly.

BradleyW · 08-03-09

good night everyone. time to call it a night here in Britian. 2 in the morning

dennyb · 08-03-09

Quote:

Originally Posted by NoGuru

I hand write my stuff down so I can change it on the fly.

yeah, I do some stuff and have it in a folder on my desk but what about your screenshots and your CPUZ validations. If you store them here on line, and in email folders on line you will still have them if you lose the OS.

the 2 harddrives is good

grishkathefool · 08-03-09

I make my 7 year old memorize them by rote...

ACHILEE5 · 08-03-09

Quote:

Originally Posted by dennyb

I scrapped my 4.25 fft- no LLC clock and am now 1:12 into 4.25 blend LLC--Max Temps 71/69/65/65

edit 1.376v CPUZ

How have you guys been saving your overclock documents? I have been putting mine into a PM to myself and then into a folder. I also e-mail them to myself and store them in a yahoo mail folder. That way if I lose the OS I still have all of my documents stored in two places. So, how do you guys go about it?

Hi

Is that to join the Elite 4GHz with a Star Club

I'm in at 4GHz, or should that be "you got me in at 4GHz"

supaspoon · 08-03-09

Quote:

Originally Posted by dennyb

I knew that the i7's ran hotter than the 775's,but are you hitting the temp limit on water with volts to give? I guess the only way to beat the heat is to run a good dual core

. O' what is it about the P95 blend test @ the 17 to 20 minute mark that blows the temps out of sight? My temps look so good til they hit that time period

Well supa, if you see this post and decide to answer it--type loud so i can hear you, Hoover is on full throttle and my pant leg is whippin' in the wind

Yeah, on full load it sits in the low 70's, occasionally nipping 76. I'm sure it's due to the HT though. Haven't messed about much w/ it off yet but from what I hear it runs about 10+c hotter than w/ it off. The idle temps are around high 30's/ low 40's which is about the same i got on the c2q. So it just pushes the temps quite a bit harder on load. May try tonight to see what I can squeeze out of her w/ it off though.....just for giggles.

Quote:

Originally Posted by grishkathefool

Post # 5000

EP45-UD3P for Life!!

ok, so I don't do photo mods so well... but hey, it only took 5 mins.

EPIC! Look at the Nog'in on that kid.

Quote:

Originally Posted by crashdummy35

That's what I'm talking about. Even though my Vegas work is extremely amature-ish, C2D's are severely lacking in this department. Even at 3.9GHz my render time on a heavily effects laden video (Pro Titler, pip, Particle Illusion) is pretty slow.

Hopefully I'll be out of the poor house in a few months and can at least grab a Q9550.

@dennyb. I see you are slowly climbing that mountain. 4.5 is almost in sight for you by now. Good luck.

Yeah, it's easy to get carried away w/ a scene and land yourself some nice several hour per frame renders. I wanted to build a dual xeon 55xx, but given the cost & the fact that there's no 1366 dually boards that allow oc'ing, I decided to wait it out on the hopes of a 1366 skulltrail board. I think if there's going to be one, we'll probably see it by the middle of next year. But right now it's all still just rumors/speculation as far as I can tell.

Quote:

Originally Posted by grishkathefool

I make my 7 year old memorize them by rote...

Lol, you're just full of 'epic' tonight aren't you?

But yeah I just write my stuff down. Also do the data dedicated hd thing too though, but it's not really for oc stuff, just to keep my working files safe etc.

		Overclock.net - Overclocking.net > Intel > Intel Motherboards
Gigabyte EP45-UD3P Owners Guide

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)