[hwbot] SuperPi 1M ranking - Page 3 - Overclock.net

**gonX** · 05-19-07

For everyones information, in this thread specifically, you can't update by using the [hwbot] tags. You'll need to submit it manually through hwbot.org

RuSo · 05-19-07

well a new score, but if i go 1mhz higher on my FSB my score goes.....down???
Edit: ahh figured it out.....

Quote:

Any tRAS setting lower tRCD + CAS + 2 cycles will allow the memory controller to close the page “in your face!” over and again and that will cause a performance hit because of a truncated transfer that needs to be repeated. Along with those hassles comes the self-explanatory risk for data corruption. That one is not a real problem as long as the system is kept running but in case it is shut down and the memory content is written back to the hard disk drive, the consequences can be catastrophic. For the drive, that is. <-

Source: http://www.mushkin.com/doc/techSuppo...rs/latency.asp

Quote:

Also be prepared to do a little bit of testing to find which voltage works best, some sticks actually start decreasing performance if you give them more than 2.7-2.8v, while some can take up to 3v. with newer tccd/tcc5, it seems that more than 2.8v will hurt then after prolonged periods of time, while the older chips can take a bit more, and actually scale really well at cas2 with lots of voltage, but die really fast if you do that.

Source: http://eclipseoc.com/index.php?id=6,51,0,0,1,0

**gonX** · 05-19-07

Quote:

Originally Posted by RuSo

well a new score, but if i go 1mhz higher on my FSB my score goes.....down???

Most likely unstable RAM then, max Vmem on TCCD is 2.85 (or that's what the limit is before it get diminishing(sp?)), so try upping it to that.

RuSo · 05-19-07

tried, and it was running @ 2.8v, tried 2.85v same result.....had my CPU clock lower to test if that could be it, ran Lost Planet bench and my rig crashed making a screeching electric noise, rebooted and it told me that CMOS settings were bad......did not matter as i knew all the settings already...

Edit: experimented some more, and when @ 533mhz CL2.5-4-4-8 1T timings my rigs HDD stops spinning, (guess the one i removed it is not a broken drive) and BSOD's after approx. 30% memtest, but not @ 533mhz CL3-5-5-10 1T 2.75v (which produced my new score)
All tested with the same (or even lower FSB)....these modules are -> according to this list Source: thanks to TheDuke XMS-PC4400C25 (2.5-4-4-8-1T)
Samsung TCCD Brainpower PCB....

Namrac · 05-19-07

I've submitted it through HWbot, but it still hasn't updated?

*ncsa* · 05-20-07

Updated now ... and a nice 3700 there

Quote:

Originally Posted by Namrac

I've submitted it through HWbot, but it still hasn't updated?

EDIT: Need to fix your CPU on the Bot so it is recognised, just edit your entry and then update

**grunion** · 05-20-07

Do we submit in the threads or the HWBot site?
I've submitted 2 scores on the HWBot site, the screen shots I attached link back to OCN instead of my shot

*ncsa* · 05-20-07

Manually submit your results on the bot, Post one for each thread at OCN will get updated reasonably quickly ...

Quote:

Originally Posted by grunion

Do we submit in the threads or the HWBot site?
I've submitted 2 scores on the HWBot site, the screen shots I attached link back to OCN instead of my shot

**grunion** · 05-20-07

Quote:

Originally Posted by ncsa

Manually submit your results on the bot, Post one for each thread at OCN will get updated reasonably quickly ...

What about the screenshot I attached at hwbot, it's not showing?
When you open the link it directs you to the OCN homepage.
My AM3 score is good for the #1 7800GS spot, 2 points w00t.
I posted the cropped image by mistake, the image below is the one I wanted to post.
I can't seem to change my attached screens on hwbot.

**gonX** · 05-20-07

Quote:

Originally Posted by grunion

What about the screenshot I attached at hwbot, it's not showing?
When you open the link it directs you to the OCN homepage.
My AM3 score is good for the #1 7800GS spot, 2 points w00t.
I posted the cropped image by mistake, the image below is the one I wanted to post.
I can't seem to change my attached screens on hwbot.

		Overclock.net - Overclocking.net > Benchmarks > Overclock.net HWBot Team
[hwbot] SuperPi 1M ranking

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)