flak-spammer

Yeah but you might end up with an unusable radiator too, in something like that you'd want a liquid to liquid heat exchanger and not a radiator.

elfudge44

I think I may end up getting another dual rad to throw in the loop. I think that may do the trick, because it seems like there is barely not enough heat dissipation with the fans at a level where you can still hold a conversation in the same room. If i crank them up to full jet speeds it seems to stay much cooler.

__________________
Phenom II 920 @ 4.0

Ultrasonic2 (muffy)

If i had the time id like to make you a new top plate ... actually when i think about it you might as well get a new block designed for a 62mm TEC in the first place. For more super cooling.

__________________

Rewindlabs

Woah....i wish my chip could do 4Ghz at those voltages

__________________
Got out of bed, could not remember my own name
Condemned to walk the soil amongst all creatures wild and tame
Go where I go, do what I must
Crawl starving on my belly
Licking up the dry dust

Demonkev666

probably needs cold to do it.

phenom II loves cold. it's

I'm waiting for C3 stepping it clocks a lot better.

__________________
chill guy as always.

Ultrasonic2 (muffy)

what voltage did you runn it at 3.64 ??

oh and did you do the 4g run with the TEC ?

__________________

elfudge44

I wish i could throw more at it . Stupid thing will not last long enough to validate at 4.2, but it is soooo close. I think a new mobo may be in order.

at 3.64 it is set to 1.45 in bios, but in cpuz idling it is at 1.424

and yep it was with the tec. at 4 it could mess around and do stuff, but it only makes it half way through a spi 1m

new top plate. I am all for getting some more of your work .

How much will you be selling your blocks for. I was thinking about getting one to compare.


Side note:

Last night i made a huge noob tec mistake.
I recently changed to windows 7 and had not changed how long it takes to go to sleep. I ran up to the gas station to get some drinks, and came back and the computer was sleeping .... but the tec was still cranking away. I am not sure how hot it got exactly, but the middle tube on my V8 sounded like i was making tea, and the water was ready.

Luckily for me nothing broke when this shenanigan went down.

Needless to say a relay is on the way.
7-10 business days till safety

__________________
Phenom II 920 @ 4.0

ira-k

Yeah Man they will heat to boiling in no time. I knocked the wire loose on my pump once, just working around on something on my mobo, I had just walked into the other room for just a minute or so when I heard a loud "Pop" went back in there and water was dripping off the ceiling......Took a minute or so to realize that it had heated the water up and blown out my res plug. I'm just glad my rig was bare back on a mat, if it had been in a case it would of been a mess.

Heres a wiring guide I did for Crydom re-lays and the Swifty/DD type, if you need it...Relay Wiring - Overclock.net ... I like the solid state Crydom the best, the part # is in the pic, you can get them new on eBay for $10 or so.

I relay all my TEC,pumps and little side PSU's to my main one so it will all come on at once.

__________________
...***Beware all ye Men born of Woman, beware the Hemogoblins***...
**E8600 @ 5751Mhz ***OCN Water Cooling Club And Picture Gallery ***150 Opty @ 3242Mhz **

elfudge44

That is the one that is on its way. I got it for $18 on ebay.

__________________
Phenom II 920 @ 4.0

ira-k

Cool! Thats a good one. They've gone up, I bought 3 a couple of years ago and I think they were $10-12 each. Still $18 bux for piece of mind isn't bad at all.

__________________
...***Beware all ye Men born of Woman, beware the Hemogoblins***...
**E8600 @ 5751Mhz ***OCN Water Cooling Club And Picture Gallery ***150 Opty @ 3242Mhz **