Overclock.net › Forums › Intel › Intel Motherboards › >>The Official ASUS P8P67/P8Z68 & P8Z68/GEN3 Series Owners Club>>
New Posts  All Forums:Forum Nav:

>>The Official ASUS P8P67/P8Z68 & P8Z68/GEN3 Series Owners Club>> - Page 407

post #4061 of 9343
Quote:
Originally Posted by slimex View Post
Hey guys,

I get BSOD 124 while Prime testing (Custom Blend, 6000MB). The only thing I did, was switching off "Internal PLL Overvoltage", to get back the sleep mode capability. Now I can suspend, but the system is unstable. There have not been any worker errors in prime.

Here are my settings, as they were during my first test which ended with BSOD 124 after about 10-12h. Same settings with PLL Overvoltage enabled ran rock stable for 17h and an additional 12-13h.

Ai Tweaker

Ai Overclock Tuner: Manual
BLCK/PCIE Frequency: 100.0
Turbo Ratio: By All Cores
By All Cores: 48
Internal PLL Overvoltage: Disabled
Memory Frequency: 2133
DRAM Timing Control: CL 9 - 11 - 9 - 28 - 2T
(same like in X.M.P. except the 2T, which is 1T there)
EPU Power Saving MODE: Disabled


Ai Tweaker\\ CPU Power Management >

CPU Ratio: Auto
Enhanced Intel SpeedStep Technology: Enabled
Turbo Mode: Enabled
Long Duration Power Limit: 140 Watt
Long Duration Maintained: 32s
Short Duration Power Limit: Auto
Additional Turbo Voltage: Auto
Primary Plane Current Limit: Auto


Ai Tweaker (in the DIGI+ VRM section)

Load-Line Calibration: Ultra High
VRM Frequency: Manual
VRM Fixed Frequency Mode: 350
Phase Control: Extreme
Duty Control: Extreme
CPU Current Capability: 140%
CPU Voltage: Offset Mode
Offset Mode Sign: +
CPU Offset Voltage: 0.020V
DRAM Voltage: 1.65V
VCCSA Voltage: Auto
VCCIO Voltage: 1,15V
CPU PLL Voltage: Auto
PCH Voltage: Auto
CPU Spread Spectrum: Enabled


Advanced\\ CPU Configuration >

CPU Ratio: Auto
Intel Adaptive Thermal Monitor: Enabled
Active Processor Cores: All
Limit CPUID Maximum: Disabled
Execute Disable Bit: Enabled
Intel Virtualization Technology: Disabled
Enhanced Intel SpeedStep Technology: Enabled
Turbo Mode: Enabled
CPU C1E: Enabled
CPU C3 Report: Auto
CPU C6 Report: Auto

I am getting Vcores from 1.384V to 1.392V.

After First BSOD 124 I adjusted "CPU PLL Voltage" to 1,70625V. Prime ran without errors until another BSOD after 14h.
Then I tried "CPU PLL Voltage" of 1,5V and got the same BSOD after about 5 hours.
At the moment, my system (at home) runs a test with CPU PLL Voltage back to 1,70625V and increased VCCIO Voltage of 1,15625. Not sure if this will succeed.

Can anyone give advice, how to get this stable without switching on "Internal PLL Overvoltage" ?
Quote:
Originally Posted by slimex View Post
Stable for 15,5h now, hope that VCCIO raise to 1,15625 solved the problem.
Quote:
Originally Posted by slimex View Post
F**K! Again! BSOD 124 after 17,5h of Prime95 Custom Blend 6000MB. Will now raise VCCIO to 1,625 and start another Prime run.
Did not have any luck with all settings I tried. After this odyssey I set the settings I had before, which are similar to the listing in the first quote, except "Internal PLL Overvoltage", which I switched on again. This settings have been stable 17,5h+ and another 12h without Errors or BSODs.
Testing those "stabled" settings again resulted in a BSOD 124 after only 3-4 hours. Another test BSODed after about 12h.

Why is this no more stable ? I really don't know and would appreciate every help anyone can give.
     
CPUMotherboardGraphicsRAM
AMD Turion II Neo N40L 2 x 1.5Ghz HP ProLiant MicroServer Board (AMD RS785E/SB820... Onboard AMD HD4200 VGA 128MB 2 x 2GB Unbuffered DDR3 ECC 800MHz 
Hard DriveHard DriveHard DriveOS
Kingston SSDNow V+200 SSD 60 GB 4x Western Digital Caviar Green 3TB WD30EZRX RA... Samsung EcoGreen F4 2TB HD204UI (2TB Backup) Windows Server 2012 Datacenter 
Other
LSI 3ware 9650SE-4LPML 4-Port SATA Hardware Rai... 
  hide details  
Reply
     
CPUMotherboardGraphicsRAM
AMD Turion II Neo N40L 2 x 1.5Ghz HP ProLiant MicroServer Board (AMD RS785E/SB820... Onboard AMD HD4200 VGA 128MB 2 x 2GB Unbuffered DDR3 ECC 800MHz 
Hard DriveHard DriveHard DriveOS
Kingston SSDNow V+200 SSD 60 GB 4x Western Digital Caviar Green 3TB WD30EZRX RA... Samsung EcoGreen F4 2TB HD204UI (2TB Backup) Windows Server 2012 Datacenter 
Other
LSI 3ware 9650SE-4LPML 4-Port SATA Hardware Rai... 
  hide details  
Reply
post #4062 of 9343
Quote:
Originally Posted by slimex View Post
Did not have any luck with all settings I tried. After this odyssey I set the settings I had before, which are similar to the listing in the first quote, except "Internal PLL Overvoltage", which I switched on again. This settings have been stable 17,5h+ and another 12h without Errors or BSODs.
Testing those "stabled" settings again resulted in a BSOD 124 after only 3-4 hours. Another test BSODed after about 12h.

Why is this no more stable ? I really don't know and would appreciate every help anyone can give.
Stop 124 is likely vcore or VTT +/- based on your template I would bump your offset to +0.040v and test again. Also it has been my experience enabling Internal PLL prove more stable when OCing the BLCK but may have benefits at higher multi I'd leave it disabled and consider using it if you fail again. It may also be a good idea to try running your memory at say 1600 same timings for the moment and see if that helps if you have success you may well be able to tighten the timings a bit. GL
Luxe 1
(33 items)
 
Enthoo Primo
(28 items)
 
 
CPUMotherboardGraphicsRAM
i7 6700k MSI Z170A G7 GTX 1080Ti FE G.SKILL 32GB (4 x 8GB) Ripjaws V Series DDR4 PC... 
Hard DriveHard DriveHard DriveOptical Drive
Samsung 950 Pro M.2 WDC WD1003FZEX-00MK2A0 Seagate Backup+ Desk SCSI Disk Device asus bc-12b1st 
CoolingCoolingCoolingCooling
XSPC Raystorm Pro Alphacool NexXxoS UT60 Full Copper 240mm radiator  Monsoon Series Two D5 Premium Dual Bay Reservoi... Phanteks PH-F140SP Case Fan 
CoolingCoolingCoolingCooling
Aquacomputer backplate for kryographics Pascal ... corsair sp120 high performance led tygon plasticizer free kryographics Pascal for NVIDIA TITAN X and GTX ... 
CoolingCoolingCoolingOS
Mayhem Pastel White UV Monsoon center compression fittings  Alphacool NexXxoS XT45 Full Copper 280mm radiator  Windows 10 Pro x64 
MonitorMonitorKeyboardPower
BenQ BL3200PT CAD Professional Monitor  Asus PB278Q (Extended) Corsair Gaming K70 LUX RGB Mechanical Gaming Ke... CORSAIR HX Series HX750 750W ATX12V 2.3 / EPS12... 
CaseMouseMouse PadAudio
Phanteks Enthoo Luxe PH-ES614L  Func MS-3 rev2 Cooler Master Speed RX Creative Sound Blaster Zx 116dB PCIe Gaming Sou... 
AudioAudioOtherOther
Logitech Z906 5.1 Surround Sound Speaker System... HyperX KHX-H3CLW Cloud Gaming Headset - White  Darkside dimable LED strips  Modsmart Kobra Cables 
Other
EVGA PowerLink 
CPUMotherboardGraphicsGraphics
i7 4790k @ 4.8 MSI Z97 Gaming 7  Saphire R9 290x (hynix) Saphire R9 290x (Hynix) 
RAMHard DriveHard DriveHard Drive
GSkill Ripjaws Z F3-2400C10D-8GZH 2x Samsung 850 Pro Raid-0  AMD RAMDisk WD1001FALS (Data/Backup) 
Optical DriveCoolingOSMonitor
Asus BC-12B1ST BlueRay Custom Water Cooled Windows 10 Pro x64 Asus PG279Q 
MonitorKeyboardPowerCase
Asus PG278Q Corsair K70 EVGA 1000w G2 Phanteks Enthoo Primo 
MouseMouse PadAudioAudio
FUNC MS-3 rev2  XTRAC PADS Ripper Optical Mouse pad Kingston HyperX Cloud II  Creative Sound Blaster Z PCIe 116dB SNR Gaming ... 
OtherOtherOtherOther
Alphacool NexXxoS UT60 Full Copper 420mm EK Supremacy EVO Alphacool NexXxoS Monsta 360 Radiator EK-FC R9-290X Waterblock - Nickel Acetal (Rev.2.0) 
OtherOtherOtherOther
EK-FC R9-290X backplate Bitspower Dual / Single D5 Top Upgrade Kit 150 ... Bitspower D5 MOD TOP (Black "S" Model) PrimoFlex Advanced LRT 10ft Tubing - 1/2in. ID ... 
  hide details  
Reply
Luxe 1
(33 items)
 
Enthoo Primo
(28 items)
 
 
CPUMotherboardGraphicsRAM
i7 6700k MSI Z170A G7 GTX 1080Ti FE G.SKILL 32GB (4 x 8GB) Ripjaws V Series DDR4 PC... 
Hard DriveHard DriveHard DriveOptical Drive
Samsung 950 Pro M.2 WDC WD1003FZEX-00MK2A0 Seagate Backup+ Desk SCSI Disk Device asus bc-12b1st 
CoolingCoolingCoolingCooling
XSPC Raystorm Pro Alphacool NexXxoS UT60 Full Copper 240mm radiator  Monsoon Series Two D5 Premium Dual Bay Reservoi... Phanteks PH-F140SP Case Fan 
CoolingCoolingCoolingCooling
Aquacomputer backplate for kryographics Pascal ... corsair sp120 high performance led tygon plasticizer free kryographics Pascal for NVIDIA TITAN X and GTX ... 
CoolingCoolingCoolingOS
Mayhem Pastel White UV Monsoon center compression fittings  Alphacool NexXxoS XT45 Full Copper 280mm radiator  Windows 10 Pro x64 
MonitorMonitorKeyboardPower
BenQ BL3200PT CAD Professional Monitor  Asus PB278Q (Extended) Corsair Gaming K70 LUX RGB Mechanical Gaming Ke... CORSAIR HX Series HX750 750W ATX12V 2.3 / EPS12... 
CaseMouseMouse PadAudio
Phanteks Enthoo Luxe PH-ES614L  Func MS-3 rev2 Cooler Master Speed RX Creative Sound Blaster Zx 116dB PCIe Gaming Sou... 
AudioAudioOtherOther
Logitech Z906 5.1 Surround Sound Speaker System... HyperX KHX-H3CLW Cloud Gaming Headset - White  Darkside dimable LED strips  Modsmart Kobra Cables 
Other
EVGA PowerLink 
CPUMotherboardGraphicsGraphics
i7 4790k @ 4.8 MSI Z97 Gaming 7  Saphire R9 290x (hynix) Saphire R9 290x (Hynix) 
RAMHard DriveHard DriveHard Drive
GSkill Ripjaws Z F3-2400C10D-8GZH 2x Samsung 850 Pro Raid-0  AMD RAMDisk WD1001FALS (Data/Backup) 
Optical DriveCoolingOSMonitor
Asus BC-12B1ST BlueRay Custom Water Cooled Windows 10 Pro x64 Asus PG279Q 
MonitorKeyboardPowerCase
Asus PG278Q Corsair K70 EVGA 1000w G2 Phanteks Enthoo Primo 
MouseMouse PadAudioAudio
FUNC MS-3 rev2  XTRAC PADS Ripper Optical Mouse pad Kingston HyperX Cloud II  Creative Sound Blaster Z PCIe 116dB SNR Gaming ... 
OtherOtherOtherOther
Alphacool NexXxoS UT60 Full Copper 420mm EK Supremacy EVO Alphacool NexXxoS Monsta 360 Radiator EK-FC R9-290X Waterblock - Nickel Acetal (Rev.2.0) 
OtherOtherOtherOther
EK-FC R9-290X backplate Bitspower Dual / Single D5 Top Upgrade Kit 150 ... Bitspower D5 MOD TOP (Black "S" Model) PrimoFlex Advanced LRT 10ft Tubing - 1/2in. ID ... 
  hide details  
Reply
post #4063 of 9343
Myne has arrived.

Curious what was the source for the club image? I am taking the same shot as we speak using my 35mm 1.8 to get the depth of field effect.
RainONE
(13 items)
 
ASUS G50VT
(13 items)
 
 
CPUMotherboardGraphicsRAM
i5-2500K @ 4.5Ghz ASUS P8Z68 V PRO GTX 570 MSI TF III @ 950/1900/2300 16GB Corsair Vengeance 
Hard DriveOSKeyboardPower
2TB Seagate 5900 RPM Windows 7 x64 Ultimate Ideazon Z Board Seasonic X750 
CaseMouse
Thermaltake V9 BlacX Logitech G700 
CPUGraphicsRAMOS
Intel Core 2 Duo T9600 2.8Ghz @ 3.1Ghz Nvidia 9800M GS (OC @ 640/1600/800) 4GB DDR2 800Mhz Windows 7 
Mouse
Logitech G700 
  hide details  
Reply
RainONE
(13 items)
 
ASUS G50VT
(13 items)
 
 
CPUMotherboardGraphicsRAM
i5-2500K @ 4.5Ghz ASUS P8Z68 V PRO GTX 570 MSI TF III @ 950/1900/2300 16GB Corsair Vengeance 
Hard DriveOSKeyboardPower
2TB Seagate 5900 RPM Windows 7 x64 Ultimate Ideazon Z Board Seasonic X750 
CaseMouse
Thermaltake V9 BlacX Logitech G700 
CPUGraphicsRAMOS
Intel Core 2 Duo T9600 2.8Ghz @ 3.1Ghz Nvidia 9800M GS (OC @ 640/1600/800) 4GB DDR2 800Mhz Windows 7 
Mouse
Logitech G700 
  hide details  
Reply
post #4064 of 9343
Just downloaded BIOS 2001 for my board. It downloaded awfully slow at just 12KB/s.
post #4065 of 9343
Quote:
Originally Posted by hmar View Post
I don't know exactly what mechanism drives the TurboV EVO autotuning but setting the Dram voltage to it's nominal 1.5V overclocks my i7 2600K to 103*43,
setting the Dram voltage to 1.6V overclocks to 104.6*46. One thing particuliar:

Internal PLL must be enabled. Without, my machine doesn't boot not even at the "optimized settings" 103*43. Ennoying is the 2x reset at bootup.
All of this is because you're using ASUS Suite II's automatic overclocking feature. Generally, it's better to do it manually in the UEFI starting with a BCLK of 100.0 MHz and never changing it.

To be honest, I recommend uninstalling Ai Suite II unless you absolutely need it for something else.


Quote:
Originally Posted by slimex View Post
Hey guys,

I get BSOD 124 while Prime testing (Custom Blend, 6000MB). The only thing I did, was switching off "Internal PLL Overvoltage", to get back the sleep mode capability. Now I can suspend, but the system is unstable. There have not been any worker errors in prime.

Here are my settings, as they were during my first test which ended with BSOD 124 after about 10-12h. Same settings with PLL Overvoltage enabled ran rock stable for 17h and an additional 12-13h.

Ai Tweaker

Ai Overclock Tuner: Manual
BLCK/PCIE Frequency: 100.0
Turbo Ratio: By All Cores
By All Cores: 48
Internal PLL Overvoltage: Disabled
Memory Frequency: 2133
DRAM Timing Control: CL 9 - 11 - 9 - 28 - 2T
(same like in X.M.P. except the 2T, which is 1T there)
EPU Power Saving MODE: Disabled


Ai Tweaker\\ CPU Power Management >

CPU Ratio: Auto
Enhanced Intel SpeedStep Technology: Enabled
Turbo Mode: Enabled
Long Duration Power Limit: 140 Watt
Long Duration Maintained: 32s
Short Duration Power Limit: Auto
Additional Turbo Voltage: Auto
Primary Plane Current Limit: Auto


Ai Tweaker (in the DIGI+ VRM section)

Load-Line Calibration: Ultra High
VRM Frequency: Manual
VRM Fixed Frequency Mode: 350
Phase Control: Extreme
Duty Control: Extreme
CPU Current Capability: 140%
CPU Voltage: Offset Mode
Offset Mode Sign: +
CPU Offset Voltage: 0.020V
DRAM Voltage: 1.65V
VCCSA Voltage: Auto
VCCIO Voltage: 1,15V
CPU PLL Voltage: Auto
PCH Voltage: Auto
CPU Spread Spectrum: Enabled


Advanced\\ CPU Configuration >

CPU Ratio: Auto
Intel Adaptive Thermal Monitor: Enabled
Active Processor Cores: All
Limit CPUID Maximum: Disabled
Execute Disable Bit: Enabled
Intel Virtualization Technology: Disabled
Enhanced Intel SpeedStep Technology: Enabled
Turbo Mode: Enabled
CPU C1E: Enabled
CPU C3 Report: Auto
CPU C6 Report: Auto

I am getting Vcores from 1.384V to 1.392V.

After First BSOD 124 I adjusted "CPU PLL Voltage" to 1,70625V. Prime ran without errors until another BSOD after 14h.
Then I tried "CPU PLL Voltage" of 1,5V and got the same BSOD after about 5 hours.
At the moment, my system (at home) runs a test with CPU PLL Voltage back to 1,70625V and increased VCCIO Voltage of 1,15625. Not sure if this will succeed.

Can anyone give advice, how to get this stable without switching on "Internal PLL Overvoltage" ?
Quote:
Originally Posted by slimex View Post
Stable for 15,5h now, hope that VCCIO raise to 1,15625 solved the problem.
Quote:
Originally Posted by slimex View Post
F**K! Again! BSOD 124 after 17,5h of Prime95 Custom Blend 6000MB. Will now raise VCCIO to 1,625 and start another Prime run.
Quote:
Originally Posted by slimex View Post
Did not have any luck with all settings I tried. After this odyssey I set the settings I had before, which are similar to the listing in the first quote, except "Internal PLL Overvoltage", which I switched on again. This settings have been stable 17,5h+ and another 12h without Errors or BSODs.
Testing those "stabled" settings again resulted in a BSOD 124 after only 3-4 hours. Another test BSODed after about 12h.

Why is this no more stable ? I really don't know and would appreciate every help anyone can give.
Pardon my confusion, but are you saying here that having Internal PLL Overvoltage enabled doesn't stabilize it like you once thought, or are you saying that enabling it is the only way to stabilize it?
It's a computer!
(19 items)
 
  
CPUMotherboardGraphicsRAM
i5-2500K @ 4.5GHz (1.368-1.384V fixed voltage) ASUS P8P67 EVO B3 (UEFI ver. 1850) GTX 780 ASUS DirectCU II (1228 / 6300, 1.180V) G.SKILL Ripjaws X 8GB (2 x 4GB) 1866MHz, CL9 
Hard DriveHard DriveHard DriveOptical Drive
250 GB Samsung 840 EVO (C:\) 250 GB Samsung 840 EVO (D:\) 150 GB WD VelociRaptor Samsung SH-S243N 24x DVD Burner 
Optical DriveCoolingOSMonitor
Samsung SH-S203N 20X DVD Burner Thermaltake Frio Win 7 Home Premium x64 SP1 Retail AOC G2460PG (24" 1920 x 1080 144Hz G-SYNC) 
KeyboardPowerCaseMouse
Filco Majestouch 104-key Cherry MX Blues w/NKRO Corsair HX650 (Bronze, ordered on 12-12-2009) CM 690 Intellimouse Optical (1.1A) 1000Hz polling rate 
Mouse PadAudioAudio
Basic, but premium round X-Fi Titanium HD Klipsch ProMedia 2.1 (with 16 AWG Monster Cable... 
  hide details  
Reply
It's a computer!
(19 items)
 
  
CPUMotherboardGraphicsRAM
i5-2500K @ 4.5GHz (1.368-1.384V fixed voltage) ASUS P8P67 EVO B3 (UEFI ver. 1850) GTX 780 ASUS DirectCU II (1228 / 6300, 1.180V) G.SKILL Ripjaws X 8GB (2 x 4GB) 1866MHz, CL9 
Hard DriveHard DriveHard DriveOptical Drive
250 GB Samsung 840 EVO (C:\) 250 GB Samsung 840 EVO (D:\) 150 GB WD VelociRaptor Samsung SH-S243N 24x DVD Burner 
Optical DriveCoolingOSMonitor
Samsung SH-S203N 20X DVD Burner Thermaltake Frio Win 7 Home Premium x64 SP1 Retail AOC G2460PG (24" 1920 x 1080 144Hz G-SYNC) 
KeyboardPowerCaseMouse
Filco Majestouch 104-key Cherry MX Blues w/NKRO Corsair HX650 (Bronze, ordered on 12-12-2009) CM 690 Intellimouse Optical (1.1A) 1000Hz polling rate 
Mouse PadAudioAudio
Basic, but premium round X-Fi Titanium HD Klipsch ProMedia 2.1 (with 16 AWG Monster Cable... 
  hide details  
Reply
post #4066 of 9343
Quote:
Originally Posted by TwoCables View Post
Pardon my confusion, but are you saying here that having Internal PLL Overvoltage enabled doesn't stabilize it like you once thought, or are you saying that enabling it is the only way to stabilize it?
I meant, that it did not stabilize it as I thought. After switching it on again I had the same setting, which once was stable. But it wasn't. I am now testing with it Enabled and Offset +0,04 instead of +0,02. When I left this morning, Prime already ran 9h. Hope it will prove stable, then I will try again disabling "internal PLL Overvoltage"
     
CPUMotherboardGraphicsRAM
AMD Turion II Neo N40L 2 x 1.5Ghz HP ProLiant MicroServer Board (AMD RS785E/SB820... Onboard AMD HD4200 VGA 128MB 2 x 2GB Unbuffered DDR3 ECC 800MHz 
Hard DriveHard DriveHard DriveOS
Kingston SSDNow V+200 SSD 60 GB 4x Western Digital Caviar Green 3TB WD30EZRX RA... Samsung EcoGreen F4 2TB HD204UI (2TB Backup) Windows Server 2012 Datacenter 
Other
LSI 3ware 9650SE-4LPML 4-Port SATA Hardware Rai... 
  hide details  
Reply
     
CPUMotherboardGraphicsRAM
AMD Turion II Neo N40L 2 x 1.5Ghz HP ProLiant MicroServer Board (AMD RS785E/SB820... Onboard AMD HD4200 VGA 128MB 2 x 2GB Unbuffered DDR3 ECC 800MHz 
Hard DriveHard DriveHard DriveOS
Kingston SSDNow V+200 SSD 60 GB 4x Western Digital Caviar Green 3TB WD30EZRX RA... Samsung EcoGreen F4 2TB HD204UI (2TB Backup) Windows Server 2012 Datacenter 
Other
LSI 3ware 9650SE-4LPML 4-Port SATA Hardware Rai... 
  hide details  
Reply
post #4067 of 9343
Quote:
Originally Posted by slimex View Post
I meant, that it did not stabilize it as I thought. After switching it on again I had the same setting, which once was stable. But it wasn't. I am now testing with it Enabled and Offset +0,04 instead of +0,02. When I left this morning, Prime already ran 9h. Hope it will prove stable, then I will try again disabling "internal PLL Overvoltage"
Oh, ok.

I'm looking forward to the results, whatever they may be!
It's a computer!
(19 items)
 
  
CPUMotherboardGraphicsRAM
i5-2500K @ 4.5GHz (1.368-1.384V fixed voltage) ASUS P8P67 EVO B3 (UEFI ver. 1850) GTX 780 ASUS DirectCU II (1228 / 6300, 1.180V) G.SKILL Ripjaws X 8GB (2 x 4GB) 1866MHz, CL9 
Hard DriveHard DriveHard DriveOptical Drive
250 GB Samsung 840 EVO (C:\) 250 GB Samsung 840 EVO (D:\) 150 GB WD VelociRaptor Samsung SH-S243N 24x DVD Burner 
Optical DriveCoolingOSMonitor
Samsung SH-S203N 20X DVD Burner Thermaltake Frio Win 7 Home Premium x64 SP1 Retail AOC G2460PG (24" 1920 x 1080 144Hz G-SYNC) 
KeyboardPowerCaseMouse
Filco Majestouch 104-key Cherry MX Blues w/NKRO Corsair HX650 (Bronze, ordered on 12-12-2009) CM 690 Intellimouse Optical (1.1A) 1000Hz polling rate 
Mouse PadAudioAudio
Basic, but premium round X-Fi Titanium HD Klipsch ProMedia 2.1 (with 16 AWG Monster Cable... 
  hide details  
Reply
It's a computer!
(19 items)
 
  
CPUMotherboardGraphicsRAM
i5-2500K @ 4.5GHz (1.368-1.384V fixed voltage) ASUS P8P67 EVO B3 (UEFI ver. 1850) GTX 780 ASUS DirectCU II (1228 / 6300, 1.180V) G.SKILL Ripjaws X 8GB (2 x 4GB) 1866MHz, CL9 
Hard DriveHard DriveHard DriveOptical Drive
250 GB Samsung 840 EVO (C:\) 250 GB Samsung 840 EVO (D:\) 150 GB WD VelociRaptor Samsung SH-S243N 24x DVD Burner 
Optical DriveCoolingOSMonitor
Samsung SH-S203N 20X DVD Burner Thermaltake Frio Win 7 Home Premium x64 SP1 Retail AOC G2460PG (24" 1920 x 1080 144Hz G-SYNC) 
KeyboardPowerCaseMouse
Filco Majestouch 104-key Cherry MX Blues w/NKRO Corsair HX650 (Bronze, ordered on 12-12-2009) CM 690 Intellimouse Optical (1.1A) 1000Hz polling rate 
Mouse PadAudioAudio
Basic, but premium round X-Fi Titanium HD Klipsch ProMedia 2.1 (with 16 AWG Monster Cable... 
  hide details  
Reply
post #4068 of 9343
Hi,

I have recently built my new rig with the P8Z68-V Pro as the foundation. I am happy with the purchase apart form two annoying niggles.

The first is the double cold boot issue and I will be trying the two fixes shown on the first page of this section. However, the advice is to first update the BIOS. Sound advice I am sure, but the last time i tried to flash my BIOS on an ASUS motherboard, i fried it and had to replace it. Therefore, I approach that task with some trepidation. The MOBO enables me to update the BIOS via USB, coolio, on the ASUS website there are multiple BIOS updates. Now for the noobatron quesiton 'Do I flash all the versions there in order, or just the newest entry in the list?

The second issue I am having, is that when I use my headset (stereo 3.5 mm connection to on board soundcard), i get horrible noise/screech every time i move my mouse, it also happens when I maximize and minimize a webpage, not to mention the noise it makes when i run BF3. Has anyone else had this issue and does anyone know any fixes. I have read some reference to Graphics Card issues (i have a 6950) but this did not happen with my previous rig with that card installed. Basically I have put a new mobo, i5 2500k and 8gb ram into my old machine with 750 W PSU and swapped the cables. Nothing else has changed.

I apologize for the noobiness of the questions and if I have missed the information elsewhere (i have searched this forum), but I would very much appreciate your wisdom in these matters.

Cheers!
Monolith v3.0
(13 items)
 
  
CPUMotherboardGraphicsRAM
Core i5 2500k @ 3.3 Ghz Asus P8Z68-V Pro HD6950 8 GB 
Hard DriveOptical DriveOSMonitor
500 GB DVD-ROM and BLU-RAY Windows 7 HP x64 Samsung 24" 1080p 
KeyboardCaseMouseMouse Pad
Cyborg V.7 Antec P180 Cyborg R.A.T.9 Cyborg V.3 Surface 
  hide details  
Reply
Monolith v3.0
(13 items)
 
  
CPUMotherboardGraphicsRAM
Core i5 2500k @ 3.3 Ghz Asus P8Z68-V Pro HD6950 8 GB 
Hard DriveOptical DriveOSMonitor
500 GB DVD-ROM and BLU-RAY Windows 7 HP x64 Samsung 24" 1080p 
KeyboardCaseMouseMouse Pad
Cyborg V.7 Antec P180 Cyborg R.A.T.9 Cyborg V.3 Surface 
  hide details  
Reply
post #4069 of 9343
Flash the latest bios.

Using USB ports that at any point cross the sound cabling or are near the cards are a common issue for noise. I cant use my laptops usb port near the audio jacks and enjoy the sound jacks at the same time. Just check that your avoiding this type of thing. If so then not sure what to tell you.
RainONE
(13 items)
 
ASUS G50VT
(13 items)
 
 
CPUMotherboardGraphicsRAM
i5-2500K @ 4.5Ghz ASUS P8Z68 V PRO GTX 570 MSI TF III @ 950/1900/2300 16GB Corsair Vengeance 
Hard DriveOSKeyboardPower
2TB Seagate 5900 RPM Windows 7 x64 Ultimate Ideazon Z Board Seasonic X750 
CaseMouse
Thermaltake V9 BlacX Logitech G700 
CPUGraphicsRAMOS
Intel Core 2 Duo T9600 2.8Ghz @ 3.1Ghz Nvidia 9800M GS (OC @ 640/1600/800) 4GB DDR2 800Mhz Windows 7 
Mouse
Logitech G700 
  hide details  
Reply
RainONE
(13 items)
 
ASUS G50VT
(13 items)
 
 
CPUMotherboardGraphicsRAM
i5-2500K @ 4.5Ghz ASUS P8Z68 V PRO GTX 570 MSI TF III @ 950/1900/2300 16GB Corsair Vengeance 
Hard DriveOSKeyboardPower
2TB Seagate 5900 RPM Windows 7 x64 Ultimate Ideazon Z Board Seasonic X750 
CaseMouse
Thermaltake V9 BlacX Logitech G700 
CPUGraphicsRAMOS
Intel Core 2 Duo T9600 2.8Ghz @ 3.1Ghz Nvidia 9800M GS (OC @ 640/1600/800) 4GB DDR2 800Mhz Windows 7 
Mouse
Logitech G700 
  hide details  
Reply
post #4070 of 9343
Quote:
Originally Posted by Caliban86 View Post
Hi,

I have recently built my new rig with the P8Z68-V Pro as the foundation. I am happy with the purchase apart form two annoying niggles.

The first is the double cold boot issue and I will be trying the two fixes shown on the first page of this section. However, the advice is to first update the BIOS. Sound advice I am sure, but the last time i tried to flash my BIOS on an ASUS motherboard, i fried it and had to replace it. Therefore, I approach that task with some trepidation. The MOBO enables me to update the BIOS via USB, coolio, on the ASUS website there are multiple BIOS updates. Now for the noobatron quesiton 'Do I flash all the versions there in order, or just the newest entry in the list?
You can flash directly to the latest BIOS.

I personally recommending the built-in flashing utility that is right in the UEFI itself. It is located in the Tools tab.

I have no experience with this booting issue, so I don't know if it's a guaranteed fix. However, I will tell you one thing about flashing the BIOS: any saved profiles are lost because the entire BIOS (the entire UEFI) is replaced.


Quote:
Originally Posted by SeanWebster
The second issue I am having, is that when I use my headset (stereo 3.5 mm connection to on board soundcard), i get horrible noise/screech every time i move my mouse, it also happens when I maximize and minimize a webpage, not to mention the noise it makes when i run BF3. Has anyone else had this issue and does anyone know any fixes. I have read some reference to Graphics Card issues (i have a 6950) but this did not happen with my previous rig with that card installed. Basically I have put a new mobo, i5 2500k and 8gb ram into my old machine with 750 W PSU and swapped the cables. Nothing else has changed.

I apologize for the noobiness of the questions and if I have missed the information elsewhere (i have searched this forum), but I would very much appreciate your wisdom in these matters.

Cheers!
I don't know what to do with this one.
It's a computer!
(19 items)
 
  
CPUMotherboardGraphicsRAM
i5-2500K @ 4.5GHz (1.368-1.384V fixed voltage) ASUS P8P67 EVO B3 (UEFI ver. 1850) GTX 780 ASUS DirectCU II (1228 / 6300, 1.180V) G.SKILL Ripjaws X 8GB (2 x 4GB) 1866MHz, CL9 
Hard DriveHard DriveHard DriveOptical Drive
250 GB Samsung 840 EVO (C:\) 250 GB Samsung 840 EVO (D:\) 150 GB WD VelociRaptor Samsung SH-S243N 24x DVD Burner 
Optical DriveCoolingOSMonitor
Samsung SH-S203N 20X DVD Burner Thermaltake Frio Win 7 Home Premium x64 SP1 Retail AOC G2460PG (24" 1920 x 1080 144Hz G-SYNC) 
KeyboardPowerCaseMouse
Filco Majestouch 104-key Cherry MX Blues w/NKRO Corsair HX650 (Bronze, ordered on 12-12-2009) CM 690 Intellimouse Optical (1.1A) 1000Hz polling rate 
Mouse PadAudioAudio
Basic, but premium round X-Fi Titanium HD Klipsch ProMedia 2.1 (with 16 AWG Monster Cable... 
  hide details  
Reply
It's a computer!
(19 items)
 
  
CPUMotherboardGraphicsRAM
i5-2500K @ 4.5GHz (1.368-1.384V fixed voltage) ASUS P8P67 EVO B3 (UEFI ver. 1850) GTX 780 ASUS DirectCU II (1228 / 6300, 1.180V) G.SKILL Ripjaws X 8GB (2 x 4GB) 1866MHz, CL9 
Hard DriveHard DriveHard DriveOptical Drive
250 GB Samsung 840 EVO (C:\) 250 GB Samsung 840 EVO (D:\) 150 GB WD VelociRaptor Samsung SH-S243N 24x DVD Burner 
Optical DriveCoolingOSMonitor
Samsung SH-S203N 20X DVD Burner Thermaltake Frio Win 7 Home Premium x64 SP1 Retail AOC G2460PG (24" 1920 x 1080 144Hz G-SYNC) 
KeyboardPowerCaseMouse
Filco Majestouch 104-key Cherry MX Blues w/NKRO Corsair HX650 (Bronze, ordered on 12-12-2009) CM 690 Intellimouse Optical (1.1A) 1000Hz polling rate 
Mouse PadAudioAudio
Basic, but premium round X-Fi Titanium HD Klipsch ProMedia 2.1 (with 16 AWG Monster Cable... 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel Motherboards
Overclock.net › Forums › Intel › Intel Motherboards › >>The Official ASUS P8P67/P8Z68 & P8Z68/GEN3 Series Owners Club>>