Overclock.net › Forums › Intel › Intel Motherboards › UD-9 Ram Issue
New Posts  All Forums:Forum Nav:

UD-9 Ram Issue - Page 2

post #11 of 24
I would say it needs more VTT voltage as well, that is usually my problem when it comes to disappearing memory. If that doesn't do it, try loosening off the cpu heatsink a bit, clamping it down too tight can also cause this issue.

Quote:
Originally Posted by Sin0822 View Post
Yup you gotta fewest the cpu and had. Or you need more QPI/Vtt

Edited by FtW 420 - 5/16/11 at 10:54am
    
CPUMotherboardGraphicsRAM
i7 990x/3930k/3770k/4770k GB x58a-OC/Asus RIVE/x79 gd65/z77 mpower/z77 MV... gtx480s/gtx580s/7970s/680s/Titan Hyper/PSC/BBSE/Hynix/Samsung 
Hard DriveOptical DriveCoolingOS
HDDs/SSDs DVD Air/water/phase/copper pot Windowz 
MonitorKeyboardPowerCase
samsung 2320 Razer Lycosa ax1200 carboard box 
Mouse
Trackball 
  hide details  
Reply
    
CPUMotherboardGraphicsRAM
i7 990x/3930k/3770k/4770k GB x58a-OC/Asus RIVE/x79 gd65/z77 mpower/z77 MV... gtx480s/gtx580s/7970s/680s/Titan Hyper/PSC/BBSE/Hynix/Samsung 
Hard DriveOptical DriveCoolingOS
HDDs/SSDs DVD Air/water/phase/copper pot Windowz 
MonitorKeyboardPowerCase
samsung 2320 Razer Lycosa ax1200 carboard box 
Mouse
Trackball 
  hide details  
Reply
post #12 of 24
Thread Starter 
Quote:
Originally Posted by FtW 420 View Post
I would say it needs more VTT voltage as well, that is usually my problem when it comes to disappearing memory. If that doesn't do it, try loosening off the cpu heatsink a bit, clamping it down too tight can also cause this issue.



Any ideas how much I should up it just for stock speeds? on ram and cpu?

Thanks, Sir Overkill.
RIGIE
(13 items)
 
  
CPUMotherboardGraphicsRAM
990X 4.5GHz 24/7 GA-X58A-UD9 4X EVGA SC 580 in SLI Dominator GT (3x2Gb)2000 
Hard DriveOSMonitorKeyboard
OCZ 120GB SSD/WD 27" 32" Logitech MX 5500 
PowerCaseMouseMouse Pad
Antec Quattro 1200W OC Lian-Li PC-P80 Logitech None 
  hide details  
Reply
RIGIE
(13 items)
 
  
CPUMotherboardGraphicsRAM
990X 4.5GHz 24/7 GA-X58A-UD9 4X EVGA SC 580 in SLI Dominator GT (3x2Gb)2000 
Hard DriveOSMonitorKeyboard
OCZ 120GB SSD/WD 27" 32" Logitech MX 5500 
PowerCaseMouseMouse Pad
Antec Quattro 1200W OC Lian-Li PC-P80 Logitech None 
  hide details  
Reply
post #13 of 24
I would just bump it up a notch or 2 at a time until it is all seen in the bios & stable in windows. With gulftown the uncore only needs to be 1.5x the memory speed, gigabyte boards usually set it 2 setting higher which is fine.
Under 3500Mhz uncore it should only need 1.3V vtt or less.
    
CPUMotherboardGraphicsRAM
i7 990x/3930k/3770k/4770k GB x58a-OC/Asus RIVE/x79 gd65/z77 mpower/z77 MV... gtx480s/gtx580s/7970s/680s/Titan Hyper/PSC/BBSE/Hynix/Samsung 
Hard DriveOptical DriveCoolingOS
HDDs/SSDs DVD Air/water/phase/copper pot Windowz 
MonitorKeyboardPowerCase
samsung 2320 Razer Lycosa ax1200 carboard box 
Mouse
Trackball 
  hide details  
Reply
    
CPUMotherboardGraphicsRAM
i7 990x/3930k/3770k/4770k GB x58a-OC/Asus RIVE/x79 gd65/z77 mpower/z77 MV... gtx480s/gtx580s/7970s/680s/Titan Hyper/PSC/BBSE/Hynix/Samsung 
Hard DriveOptical DriveCoolingOS
HDDs/SSDs DVD Air/water/phase/copper pot Windowz 
MonitorKeyboardPowerCase
samsung 2320 Razer Lycosa ax1200 carboard box 
Mouse
Trackball 
  hide details  
Reply
post #14 of 24
sorry i was at chemo, i only had my phone and its stupid think auto corrects.

Reseat the CPu and heatsink.
X99 Main Rig
(10 items)
 
  
CPUMotherboardGraphicsRAM
Intel 5960X Extreme Edition @ 4.5GHz Always Changing VisonTek R9 290 G.Skill Ripjaws 4 16GB (4x4GB) DDR4 @ 3200MHz 
Hard DriveHard DriveHard DriveCooling
Samsung 128GB M.2 PCI-E 4x SSD Apotop 256GB SSD 1.82TB NAS Noctua NH-D15 with both fans 
OSPower
Win7 Pro Enermax 1000W 
  hide details  
Reply
X99 Main Rig
(10 items)
 
  
CPUMotherboardGraphicsRAM
Intel 5960X Extreme Edition @ 4.5GHz Always Changing VisonTek R9 290 G.Skill Ripjaws 4 16GB (4x4GB) DDR4 @ 3200MHz 
Hard DriveHard DriveHard DriveCooling
Samsung 128GB M.2 PCI-E 4x SSD Apotop 256GB SSD 1.82TB NAS Noctua NH-D15 with both fans 
OSPower
Win7 Pro Enermax 1000W 
  hide details  
Reply
post #15 of 24
Thread Starter 
Quote:
Originally Posted by FtW 420 View Post
I would just bump it up a notch or 2 at a time until it is all seen in the bios & stable in windows. With gulftown the uncore only needs to be 1.5x the memory speed, gigabyte boards usually set it 2 setting higher which is fine.
Under 3500Mhz uncore it should only need 1.3V vtt or less.
Quote:
Originally Posted by Sin0822 View Post
sorry i was at chemo, i only had my phone and its stupid think auto corrects.

Reseat the CPu and heatsink.
OK, Well I really don't want to reseat now because i will be in a couple weeks when I get my other cards and blocks. You only get two of these things in Indigo Xtreme, So I really need the other one for then.

I can buy more but right now I will need to wait a couple days until i can get more.

So what I have done is I have just losened the block off a bit and tried to start, I kept doing this until I got it to start and say "Recovering lost Dram"(which it always says)But then it said "update success"

So I thought yes! But then I get into windows and it says 6GB(4GB usable)

I also tried upping QPI with no luck, I tried the whole way up to 1.3v

So do you guys think a reseat will fix it? and how tight would you do it?(the ek waterblock)

I am really losing it here!

Thanks, Sir Overkill.
RIGIE
(13 items)
 
  
CPUMotherboardGraphicsRAM
990X 4.5GHz 24/7 GA-X58A-UD9 4X EVGA SC 580 in SLI Dominator GT (3x2Gb)2000 
Hard DriveOSMonitorKeyboard
OCZ 120GB SSD/WD 27" 32" Logitech MX 5500 
PowerCaseMouseMouse Pad
Antec Quattro 1200W OC Lian-Li PC-P80 Logitech None 
  hide details  
Reply
RIGIE
(13 items)
 
  
CPUMotherboardGraphicsRAM
990X 4.5GHz 24/7 GA-X58A-UD9 4X EVGA SC 580 in SLI Dominator GT (3x2Gb)2000 
Hard DriveOSMonitorKeyboard
OCZ 120GB SSD/WD 27" 32" Logitech MX 5500 
PowerCaseMouseMouse Pad
Antec Quattro 1200W OC Lian-Li PC-P80 Logitech None 
  hide details  
Reply
post #16 of 24
you wanna make sure contact is even, as many of these LOST DRAM crap things come from uneven mountings.
X99 Main Rig
(10 items)
 
  
CPUMotherboardGraphicsRAM
Intel 5960X Extreme Edition @ 4.5GHz Always Changing VisonTek R9 290 G.Skill Ripjaws 4 16GB (4x4GB) DDR4 @ 3200MHz 
Hard DriveHard DriveHard DriveCooling
Samsung 128GB M.2 PCI-E 4x SSD Apotop 256GB SSD 1.82TB NAS Noctua NH-D15 with both fans 
OSPower
Win7 Pro Enermax 1000W 
  hide details  
Reply
X99 Main Rig
(10 items)
 
  
CPUMotherboardGraphicsRAM
Intel 5960X Extreme Edition @ 4.5GHz Always Changing VisonTek R9 290 G.Skill Ripjaws 4 16GB (4x4GB) DDR4 @ 3200MHz 
Hard DriveHard DriveHard DriveCooling
Samsung 128GB M.2 PCI-E 4x SSD Apotop 256GB SSD 1.82TB NAS Noctua NH-D15 with both fans 
OSPower
Win7 Pro Enermax 1000W 
  hide details  
Reply
post #17 of 24
It's very likely to be a bent pin or scratched motherboard trace. Since you changed CPU's then noticed this I suspect bent pins.

I know you don't want to remove the CPU and check due to the paste you are using, but it would be best. Don't you have any normal paste to use in the meantime so you can check the socket a time or two?

Or, it's very easy to see if there is a slot issue caused by bent pin or scratched trace. Take one stick of memory and test it in the first white slot and see if it boots, if so, shut down and try the same in the second slot and see if it boots, and once more for the third slot ect. The board should boot with a single stick of memory in any white slot, if it does not boot with memory in one of the white slots only then that means there is likely a bent pin that relates to that slot, or there might be a scratched trace on the board from memory to CPU.

It can be mounting pressure, and or memory voltage or uncore settings, but since you mentioned changing out CPU's I highly suspect you have bent some pins.

It would be great if you could post some macro images of your CPU socket from a few angles in a well lit room with no flash, then we can check for you.
    
CPUMotherboardGraphicsRAM
Intel i7 980X EE ES Gigabyte GA-X58A-UD7 GIGABYTE GV-R587SO-1GD SOC 1GB GDDR5 Mushkin 998826 Ridgeback / 998966 Radioactive 
OSMonitorPower
Vista Business x64 SP2 Asus Designo MS238H 23" LED NZXT HALE90 750W 80+ GOLD 
  hide details  
Reply
    
CPUMotherboardGraphicsRAM
Intel i7 980X EE ES Gigabyte GA-X58A-UD7 GIGABYTE GV-R587SO-1GD SOC 1GB GDDR5 Mushkin 998826 Ridgeback / 998966 Radioactive 
OSMonitorPower
Vista Business x64 SP2 Asus Designo MS238H 23" LED NZXT HALE90 750W 80+ GOLD 
  hide details  
Reply
post #18 of 24
Thread Starter 
Quote:
Originally Posted by Sin0822 View Post
you wanna make sure contact is even, as many of these LOST DRAM crap things come from uneven mountings.
Thats mate, Ill have to do a reseat I think.

Quote:
Originally Posted by lsdmeasap View Post
It's very likely to be a bent pin or scratched motherboard trace. Since you changed CPU's then noticed this I suspect bent pins.

I know you don't want to remove the CPU and check due to the paste you are using, but it would be best. Don't you have any normal paste to use in the meantime so you can check the socket a time or two?

Or, it's very easy to see if there is a slot issue caused by bent pin or scratched trace. Take one stick of memory and test it in the first white slot and see if it boots, if so, shut down and try the same in the second slot and see if it boots, and once more for the third slot ect. The board should boot with a single stick of memory in any white slot, if it does not boot with memory in one of the white slots only then that means there is likely a bent pin that relates to that slot, or there might be a scratched trace on the board from memory to CPU.

It can be mounting pressure, and or memory voltage or uncore settings, but since you mentioned changing out CPU's I highly suspect you have bent some pins.

It would be great if you could post some macro images of your CPU socket from a few angles in a well lit room with no flash, then we can check for you.
Thanks for the reply, I have tried the ram like you said and all sticks work and all slots work, so im pretty sure no bent pins, well im 100% sure.

Thanks, Sir Overkill.
RIGIE
(13 items)
 
  
CPUMotherboardGraphicsRAM
990X 4.5GHz 24/7 GA-X58A-UD9 4X EVGA SC 580 in SLI Dominator GT (3x2Gb)2000 
Hard DriveOSMonitorKeyboard
OCZ 120GB SSD/WD 27" 32" Logitech MX 5500 
PowerCaseMouseMouse Pad
Antec Quattro 1200W OC Lian-Li PC-P80 Logitech None 
  hide details  
Reply
RIGIE
(13 items)
 
  
CPUMotherboardGraphicsRAM
990X 4.5GHz 24/7 GA-X58A-UD9 4X EVGA SC 580 in SLI Dominator GT (3x2Gb)2000 
Hard DriveOSMonitorKeyboard
OCZ 120GB SSD/WD 27" 32" Logitech MX 5500 
PowerCaseMouseMouse Pad
Antec Quattro 1200W OC Lian-Li PC-P80 Logitech None 
  hide details  
Reply
post #19 of 24
Great to hear! So you tested each slot by itself with one stick of memory only, and none in the other slots right? Just checking to be sure, if that's right and you can boot with a single stick of memory in any white slot then it's probably just settings!

Try these and see how you get along, ram will be at 1600 and general timings for now until you can link me to your ram specs so I can see timings. CPU also at stock, once you give me your memory info and what speed you want to try and run the CPU I could help with better settings.

Uncore multi and QPI/Vtt voltage is the key to this issue once you are sure the board is ok, so tinker with QPI/Vtt and then uncore multi's. 990X only needs 1.5 x ram multiplier, but that does hinder performance, and you can use 2x or above like with your older CPU if you want (Suggested)

If you are trying to run 2000Mhz memory, you'll need to either tell me what Bclk you want to run, or let me know and I could tell you what I would use and give settings for that. In case you get in a hurry about this, I use 168 Bclk x12 for memory and 22-24 uncore multi with the 24 of course requiring more QPI/Vtt voltage

BSOD Error codes and what they mean:
0X00000050 << Incorrect Memory Timing/Freq or Uncore Multi
0X00000124 << Incorrect QPI/Vtt Voltage (To Much/Not Enough)
0X00000101 << Not enough Vcore Voltage
0X00000109 << Not enough or too Much memory voltage


Code:
Advanced CPU Features:
CPU Clock Ratio ................................ [26x]
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC Programs
Bi-Directional PROCHOT ..................... [Enabled]


Uncore & QPI Features:
QPI Link Speed .............................. x36 or x44 (Either fine at stock Bclk)
Uncore Frequency .......................... must be at least 1.5x ram multiplier, or above.   I suggest starting at 2x or one under, so for the 1600Mhz using x12 shown below you can use 18-24+.   I'd start with 24 myself, as it would be best at this speed, but if you have hassles set x18 and i bet all your memory shows up once you find the right QPI/Vtt voltage.   22-24 if using the above suggestions on 168 Bclk

Isonchronous Frequency ..................[Enabled]


Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... 133
PCI Express Frequency (MHz) ........... [100]

C.I.A.2 [Disabled]

Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]


Advanced DRAM Features:
Performance Enhance ...................... [Standard]  << Extreme works best 
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [AUTO]  << Set x8 for 1600Mhz, or x12 and see above about that.
DRAM Timing Selectable (SPD) .......... [Manual]

Channel A + B + C

Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ......................
tRCD .......................................
tRP .........................................
tRAS .......................................

 ^^ Set to Spec of the memory, or auto for now ^^

All below Auto except for 1T command rate


##Channel A Advanced Timing Control##
tRC ........................................  (Should be = tRAS + tRP or above for stability)
tRRD .......................................
tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
tWR ........................................ 5-12 (Odd # values likely will fail)
tWTP .......................................    (tWTP Must = tWR + tWL + 4)
tWL ........................................   (tWL Must be CAS Latency -1)
tRFC .......................................
tRTP .......................................
tFAW ......................................
Command Rate (CMD) ................ 1T

##Channel A Misc Timing Control##
Round Trip Latency ...................

B2B CAS Delay ..........................


Advanced Voltage Control:

CPU
Load Line Calibration ................. [Disabled] Level 1
CPU Vcore ............................... Auto or set to what you know you need per overclock
QPI/VTT Voltage 1.150v ............ 1.3-1.45+ depends on what timings you use and what uncore speed you are choosing, higher uncore will require more voltage.   Above 4Ghz uncore will require 1.4-1.5+ most of the time

CPU PLL 1.800v ....................... Auto

MCH/ICH
PCIE 1.500v ........................... 1.5
QPI PLL 1.100v ....................... 1.2
IOH Core 1.100v ..................... 1.14
ICH I/O 1.500v ....................... 1.5
ICH Core 1.1v ........................ 1.14

DRAM
DRAM Voltage 1.500v .............. 1.66
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]
    
CPUMotherboardGraphicsRAM
Intel i7 980X EE ES Gigabyte GA-X58A-UD7 GIGABYTE GV-R587SO-1GD SOC 1GB GDDR5 Mushkin 998826 Ridgeback / 998966 Radioactive 
OSMonitorPower
Vista Business x64 SP2 Asus Designo MS238H 23" LED NZXT HALE90 750W 80+ GOLD 
  hide details  
Reply
    
CPUMotherboardGraphicsRAM
Intel i7 980X EE ES Gigabyte GA-X58A-UD7 GIGABYTE GV-R587SO-1GD SOC 1GB GDDR5 Mushkin 998826 Ridgeback / 998966 Radioactive 
OSMonitorPower
Vista Business x64 SP2 Asus Designo MS238H 23" LED NZXT HALE90 750W 80+ GOLD 
  hide details  
Reply
post #20 of 24
Thread Starter 
Quote:
Originally Posted by lsdmeasap View Post
Great to hear! So you tested each slot by itself with one stick of memory only, and none in the other slots right? Just checking to be sure, if that's right and you can boot with a single stick of memory in any white slot then it's probably just settings!

Try these and see how you get along, ram will be at 1600 and general timings for now until you can link me to your ram specs so I can see timings. CPU also at stock, once you give me your memory info and what speed you want to try and run the CPU I could help with better settings.

Uncore multi and QPI/Vtt voltage is the key to this issue once you are sure the board is ok, so tinker with QPI/Vtt and then uncore multi's. 990X only needs 1.5 x ram multiplier, but that does hinder performance, and you can use 2x or above like with your older CPU if you want (Suggested)

If you are trying to run 2000Mhz memory, you'll need to either tell me what Bclk you want to run, or let me know and I could tell you what I would use and give settings for that. In case you get in a hurry about this, I use 168 Bclk x12 for memory and 22-24 uncore multi with the 24 of course requiring more QPI/Vtt voltage

BSOD Error codes and what they mean:
0X00000050 << Incorrect Memory Timing/Freq or Uncore Multi
0X00000124 << Incorrect QPI/Vtt Voltage (To Much/Not Enough)
0X00000101 << Not enough Vcore Voltage
0X00000109 << Not enough or too Much memory voltage


Code:
Advanced CPU Features:
CPU Clock Ratio ................................ [26x]
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC Programs
Bi-Directional PROCHOT ..................... [Enabled]


Uncore & QPI Features:
QPI Link Speed .............................. x36 or x44 (Either fine at stock Bclk)
Uncore Frequency .......................... must be at least 1.5x ram multiplier, or above.   I suggest starting at 2x or one under, so for the 1600Mhz using x12 shown below you can use 18-24+.   I'd start with 24 myself, as it would be best at this speed, but if you have hassles set x18 and i bet all your memory shows up once you find the right QPI/Vtt voltage.   22-24 if using the above suggestions on 168 Bclk

Isonchronous Frequency ..................[Enabled]


Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... 133
PCI Express Frequency (MHz) ........... [100]

C.I.A.2 [Disabled]

Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]


Advanced DRAM Features:
Performance Enhance ...................... [Standard]  << Extreme works best 
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [AUTO]  << Set x8 for 1600Mhz, or x12 and see above about that.
DRAM Timing Selectable (SPD) .......... [Manual]

Channel A + B + C

Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ......................
tRCD .......................................
tRP .........................................
tRAS .......................................

 ^^ Set to Spec of the memory, or auto for now ^^

All below Auto except for 1T command rate


##Channel A Advanced Timing Control##
tRC ........................................  (Should be = tRAS + tRP or above for stability)
tRRD .......................................
tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
tWR ........................................ 5-12 (Odd # values likely will fail)
tWTP .......................................    (tWTP Must = tWR + tWL + 4)
tWL ........................................   (tWL Must be CAS Latency -1)
tRFC .......................................
tRTP .......................................
tFAW ......................................
Command Rate (CMD) ................ 1T

##Channel A Misc Timing Control##
Round Trip Latency ...................

B2B CAS Delay ..........................


Advanced Voltage Control:

CPU
Load Line Calibration ................. [Disabled] Level 1
CPU Vcore ............................... Auto or set to what you know you need per overclock
QPI/VTT Voltage 1.150v ............ 1.3-1.45+ depends on what timings you use and what uncore speed you are choosing, higher uncore will require more voltage.   Above 4Ghz uncore will require 1.4-1.5+ most of the time

CPU PLL 1.800v ....................... Auto

MCH/ICH
PCIE 1.500v ........................... 1.5
QPI PLL 1.100v ....................... 1.2
IOH Core 1.100v ..................... 1.14
ICH I/O 1.500v ....................... 1.5
ICH Core 1.1v ........................ 1.14

DRAM
DRAM Voltage 1.500v .............. 1.66
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]
Im not sure if it is settings, because i run it stock and it still has the same problem

Thanks, Sir Overkill.
RIGIE
(13 items)
 
  
CPUMotherboardGraphicsRAM
990X 4.5GHz 24/7 GA-X58A-UD9 4X EVGA SC 580 in SLI Dominator GT (3x2Gb)2000 
Hard DriveOSMonitorKeyboard
OCZ 120GB SSD/WD 27" 32" Logitech MX 5500 
PowerCaseMouseMouse Pad
Antec Quattro 1200W OC Lian-Li PC-P80 Logitech None 
  hide details  
Reply
RIGIE
(13 items)
 
  
CPUMotherboardGraphicsRAM
990X 4.5GHz 24/7 GA-X58A-UD9 4X EVGA SC 580 in SLI Dominator GT (3x2Gb)2000 
Hard DriveOSMonitorKeyboard
OCZ 120GB SSD/WD 27" 32" Logitech MX 5500 
PowerCaseMouseMouse Pad
Antec Quattro 1200W OC Lian-Li PC-P80 Logitech None 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel Motherboards
Overclock.net › Forums › Intel › Intel Motherboards › UD-9 Ram Issue