(Build Log) No name yet, Case Labs T10

Starting on Monday I will attempt to do a build log. It will have photo's of the things already done and where I am trying to go from here. I still have not made up my mine which way will be the finally way to go, but we will get there together. I will be using parts from my old system and a few new parts, mainly my new case. I am a proud owner of a Case Labs T10.

Parts:
G1 Assassin Mother board
980X CPU
6 GB of Corsairs Dominators GT 2000mHz
OCZ Agility 2 SSD 120gb x3 in RAID 0
WD Black 2TB for Itunes/Movies and some games
Seagate 2TB for back up
WD Black 640GB x2 in RAID 0 (just cause I have them. may use to back up wife lab top plus more movies if needed.)
Evga 580's in SLI( will over clock once up and running)
Corsair AX1200 Power Supply
Hanns G 28in monitor 19/12
Logitech G19 Keyboard
Logitech 9x gaming mouse
Razor Destructor mouse pad
RX360 rads x2
Possible rs360 rad(undecided on weather to use or not)
XSPC dual ras for ddc pumps which I will be running in a modify single loop. (pump1 out to rx360 to cpu to in on pump2 out on pump2 to second rx360 to gpu's to in on pump1.) As stated earlier undecided on weather to use my rs120 in the loop and if so where to put it in the loop.
I will be using AR15 1850rmp's fans for everything with old fan shell used for shrouds on rad's 4 as intake on the p/s side 3 on the rad p/s side in a push config.
two as front intake on m/b, 3 on rad with fan shroud. 1 on the back m/b side as exhaust. 2 in bottom as intakes,
4 40mm fans in back as exhaust.
sythe 12 channel fan controller
White tubing.
Fan covers will be painted od green to match the board
green led strip alone the inside of the case out of sight, you won't know it there until it is turned on.
ALL OF THIS IN MY CASE LABS T10

There is other small items that will be added. I will not be sleeving my cables as I don't know how.
ALL OF THIS WILL GO IN MY CASE LABS T10

Open for idea's and suggestions.

here, I plugged the usb ports and painted the casing black:



A couple of more shots to show the different in size compared to my HAF X

Did a little mounting and testing today. Got my res/pump mounted and fill tubs for the res ran so I would only have to take off the top to fill. I thought about drilling holes in the top for the fill holes, but decided I didn't want to mess up or change such a nice case. Even through you can order a different top.




A few more items from Jim, Some fan mounts for the M/B side.

notice the nice packaging.

More to come, trying to do a little each day.

Question, anyone know the basic different you would get on your temp with a shroud and without one.

Build put on hole spent most of today trouble shooting my system. It just went dead, shut off. Found first problem. Pump died and system over heated and shut down. Luckily I had a second pump on hand. Then SSD died. So broke up raid and went down to one for OS and second for games that way I can use Trim. After all of that top video card died. I had to redo the loop again and take out that card and just run the second card. I would not be so upset about the card was the fact that I have had problem with this card from day one. Time to RMA it. Hopefully eVGA will overnight the replacement. We will see. Now u am still up trying to get this install done before morning


Sent from my iPhone using Tapatalk

Sorry for no updates, I had a yard project that became more important then the computer(because the wife said so) Then I got hurt and spent some days in the hospital. At home now, but can't do to much. slowly get back to good health. Got some new parts in. Decided to go all compression fitting. So I cannot wait until I can post more pictures and finish this project up.

Sorry no updates. Still in hospital, doctor said I should be released on Wednesday. A day or 2 to catch up and then back to work. .


Sent from my iPhone using Tapatalk

Just got home from the hospital, Going to take a day or two to try and rest and then start up slowly. More to come