Overclock.net › Forums › Intel › Intel CPUs › Complete Overclocking Guide: Sandy Bridge & Ivy Bridge | *ASRock Edition*
New Posts  All Forums:Forum Nav:

Complete Overclocking Guide: Sandy Bridge & Ivy Bridge | *ASRock Edition* - Page 13

Poll Results: Was this guide helpful?

Poll expired: Oct 17, 2012  
  • 80% (237)
    Yes (and I DO have an ASRock motherboard).
  • 15% (45)
    Yes (but I DO NOT have an ASRock motherboard).
  • 2% (7)
    No (and I DO have an ASRock motherboard).
  • 2% (7)
    No (but I DO NOT have an ASRock motherboard).
296 Total Votes  
post #121 of 9531
Well when you disable speedstep the short and long durations are not displayed anymore only core limit. I set mine at 250 but im still at 33 multiplier, haven't started overclocking yet. I also have spread spectrum disabled. I ran a few tests w/ prime 95 at stock on fixed and my multi didn't change. Not too sure why yours still is
Z170 Build
(20 items)
 
Z68 Build
(20 items)
 
Lenovo T430
(14 items)
 
CPUMotherboardGraphicsGraphics
I7 6700K @ 4.5ghz  Gigabyte Z170x Gaming 6 XFX R9 290x 8GB XFX R9 290x 8GB 
RAMHard DriveHard DriveCooling
Gskill RipJaws V 16GB 3000mhz Samsung 850 EVO 250GB Seagate Barracuda 2TB EK-Supremacy EVO CPU Water Block 
CoolingCoolingCoolingCooling
EK R9 290X GPU Waterblocks EK-XRES 140 Revo D5 PWM Pump Alphacool NexXxoS 360mm ST30 Alphacool NexXxoS 240mm ST30 
CoolingCoolingOSMonitor
Alphacool NexXxoS 120mm ST30 Cooler Master Jetflo 120mm Fans Windows 10  LG 34UC88 
KeyboardPowerCaseMouse
Quickfire TK red switch Cooler Master V1000 MasterCase Pro 5 CM Storm Havoc 
CPUMotherboardGraphicsGraphics
I5 2500K @ 4.6ghz  ASRock Z68 Extreme 3 Gen 3 ASUS 7870 Ghz Edition ASUS 7870 Ghz Edition 
RAMHard DriveHard DriveOptical Drive
Gskill RipJaws X 16GB 1600mhz Seagate 2TB Seagate 320GB ASUS Burner 
CoolingCoolingCoolingOS
Cooler Master Eisberg 240L + 120mm Rad Koolance 3/8 x 1/2 Compression Fittings PrimoChill Advanced LRT Windows 7  
OSMonitorKeyboardPower
Ubuntu 12.04 ASUS 24" Cooler Master Quickfire TK  Cooler Master V1000 
CaseMouse
Cooler Master HAF 932 Black Edition Cooler Master Havoc 
CPUGraphicsRAMHard Drive
i5-3210M  Intel HD Graphics 4000 Gskill 16GB 1600mhz  Crucial MX200 256GB 
Hard DriveOSOSMonitor
Seagate 320GB Ubuntu 16.04 Windows 10 1600x900 
  hide details  
Reply
Z170 Build
(20 items)
 
Z68 Build
(20 items)
 
Lenovo T430
(14 items)
 
CPUMotherboardGraphicsGraphics
I7 6700K @ 4.5ghz  Gigabyte Z170x Gaming 6 XFX R9 290x 8GB XFX R9 290x 8GB 
RAMHard DriveHard DriveCooling
Gskill RipJaws V 16GB 3000mhz Samsung 850 EVO 250GB Seagate Barracuda 2TB EK-Supremacy EVO CPU Water Block 
CoolingCoolingCoolingCooling
EK R9 290X GPU Waterblocks EK-XRES 140 Revo D5 PWM Pump Alphacool NexXxoS 360mm ST30 Alphacool NexXxoS 240mm ST30 
CoolingCoolingOSMonitor
Alphacool NexXxoS 120mm ST30 Cooler Master Jetflo 120mm Fans Windows 10  LG 34UC88 
KeyboardPowerCaseMouse
Quickfire TK red switch Cooler Master V1000 MasterCase Pro 5 CM Storm Havoc 
CPUMotherboardGraphicsGraphics
I5 2500K @ 4.6ghz  ASRock Z68 Extreme 3 Gen 3 ASUS 7870 Ghz Edition ASUS 7870 Ghz Edition 
RAMHard DriveHard DriveOptical Drive
Gskill RipJaws X 16GB 1600mhz Seagate 2TB Seagate 320GB ASUS Burner 
CoolingCoolingCoolingOS
Cooler Master Eisberg 240L + 120mm Rad Koolance 3/8 x 1/2 Compression Fittings PrimoChill Advanced LRT Windows 7  
OSMonitorKeyboardPower
Ubuntu 12.04 ASUS 24" Cooler Master Quickfire TK  Cooler Master V1000 
CaseMouse
Cooler Master HAF 932 Black Edition Cooler Master Havoc 
CPUGraphicsRAMHard Drive
i5-3210M  Intel HD Graphics 4000 Gskill 16GB 1600mhz  Crucial MX200 256GB 
Hard DriveOSOSMonitor
Seagate 320GB Ubuntu 16.04 Windows 10 1600x900 
  hide details  
Reply
post #122 of 9531
Okay, I st the core current limit to 300 per the guide, no difference, the mult/speed still vacillates from 42/4.2GHz to 45/4.5GHz running OCCT. Core temps still good.

Now I'm running Handbrake, and the mult is staying stable at 45. And I'm amazed at how cool my temps are, running handbrake pushes my i7 and the temps jump to the high 50s, low 60s, my temps on this i5 are running in the upper 30s, low to mid 40s. Guess the i5 is up to the challenge.
post #123 of 9531
First of all thanks for the guide! Really helped making things a bit clearer. But I am still issues with overclocking my 2500k frown.gif

First of all my specs:
i5 2500k
ASRock Pro3 Gen3 (No LLC and fixed voltage)
XFX HD 6870
Corsair DDR3-12800 8 GB (9-9-9-24)
Corsair 500V V2 Builder series.
Cooler Master Hyper Evo 212

I can't get any overclock stable on a higher multiplier, after a while it will just drop to 33 as a multiplier and go back up to the setting i selected but this constantly switching will happen every minute or so after its first occurrence.

I tried setting the multiplier to 38, 40, 42, 45 and how higher I go how faster it will start with dropping to 33. On 45x it will drop after 5 minutes, while on 40 it can almost run 45 minutes before it starts dropping.

I have tried every option in the bios with power saving on or off, different power limits and even 1.4 voltage on 40x to see if it was the voltage. But nothing helped.

Things i have noticed:

Voltage will drop about 0.1 when multiplier goes to 33, so when i am on 1.2V with 40 multiplier it will become 1.1. On 45x it will drop from 1.3 to 1.2 or 1.35 to 1.25.

Its not thermal throttling as temps are around 65-70 degrees on 4.5 Ghz in the first 5 minutes of stress testing.

Even on 38 it will drop to 33 when stressing for 2-3 hours. So I am kinda out of options.

Only thing i haven't tried is setting the long power duriation to anything higher then 1 second. Could that be the cause?
post #124 of 9531
Quote:
Originally Posted by tootercomputer View Post

Okay, I st the core current limit to 300 per the guide, no difference, the mult/speed still vacillates from 42/4.2GHz to 45/4.5GHz running OCCT. Core temps still good.
Now I'm running Handbrake, and the mult is staying stable at 45. And I'm amazed at how cool my temps are, running handbrake pushes my i7 and the temps jump to the high 50s, low 60s, my temps on this i5 are running in the upper 30s, low to mid 40s. Guess the i5 is up to the challenge.

What cooler are you running?
Z170 Build
(20 items)
 
Z68 Build
(20 items)
 
Lenovo T430
(14 items)
 
CPUMotherboardGraphicsGraphics
I7 6700K @ 4.5ghz  Gigabyte Z170x Gaming 6 XFX R9 290x 8GB XFX R9 290x 8GB 
RAMHard DriveHard DriveCooling
Gskill RipJaws V 16GB 3000mhz Samsung 850 EVO 250GB Seagate Barracuda 2TB EK-Supremacy EVO CPU Water Block 
CoolingCoolingCoolingCooling
EK R9 290X GPU Waterblocks EK-XRES 140 Revo D5 PWM Pump Alphacool NexXxoS 360mm ST30 Alphacool NexXxoS 240mm ST30 
CoolingCoolingOSMonitor
Alphacool NexXxoS 120mm ST30 Cooler Master Jetflo 120mm Fans Windows 10  LG 34UC88 
KeyboardPowerCaseMouse
Quickfire TK red switch Cooler Master V1000 MasterCase Pro 5 CM Storm Havoc 
CPUMotherboardGraphicsGraphics
I5 2500K @ 4.6ghz  ASRock Z68 Extreme 3 Gen 3 ASUS 7870 Ghz Edition ASUS 7870 Ghz Edition 
RAMHard DriveHard DriveOptical Drive
Gskill RipJaws X 16GB 1600mhz Seagate 2TB Seagate 320GB ASUS Burner 
CoolingCoolingCoolingOS
Cooler Master Eisberg 240L + 120mm Rad Koolance 3/8 x 1/2 Compression Fittings PrimoChill Advanced LRT Windows 7  
OSMonitorKeyboardPower
Ubuntu 12.04 ASUS 24" Cooler Master Quickfire TK  Cooler Master V1000 
CaseMouse
Cooler Master HAF 932 Black Edition Cooler Master Havoc 
CPUGraphicsRAMHard Drive
i5-3210M  Intel HD Graphics 4000 Gskill 16GB 1600mhz  Crucial MX200 256GB 
Hard DriveOSOSMonitor
Seagate 320GB Ubuntu 16.04 Windows 10 1600x900 
  hide details  
Reply
Z170 Build
(20 items)
 
Z68 Build
(20 items)
 
Lenovo T430
(14 items)
 
CPUMotherboardGraphicsGraphics
I7 6700K @ 4.5ghz  Gigabyte Z170x Gaming 6 XFX R9 290x 8GB XFX R9 290x 8GB 
RAMHard DriveHard DriveCooling
Gskill RipJaws V 16GB 3000mhz Samsung 850 EVO 250GB Seagate Barracuda 2TB EK-Supremacy EVO CPU Water Block 
CoolingCoolingCoolingCooling
EK R9 290X GPU Waterblocks EK-XRES 140 Revo D5 PWM Pump Alphacool NexXxoS 360mm ST30 Alphacool NexXxoS 240mm ST30 
CoolingCoolingOSMonitor
Alphacool NexXxoS 120mm ST30 Cooler Master Jetflo 120mm Fans Windows 10  LG 34UC88 
KeyboardPowerCaseMouse
Quickfire TK red switch Cooler Master V1000 MasterCase Pro 5 CM Storm Havoc 
CPUMotherboardGraphicsGraphics
I5 2500K @ 4.6ghz  ASRock Z68 Extreme 3 Gen 3 ASUS 7870 Ghz Edition ASUS 7870 Ghz Edition 
RAMHard DriveHard DriveOptical Drive
Gskill RipJaws X 16GB 1600mhz Seagate 2TB Seagate 320GB ASUS Burner 
CoolingCoolingCoolingOS
Cooler Master Eisberg 240L + 120mm Rad Koolance 3/8 x 1/2 Compression Fittings PrimoChill Advanced LRT Windows 7  
OSMonitorKeyboardPower
Ubuntu 12.04 ASUS 24" Cooler Master Quickfire TK  Cooler Master V1000 
CaseMouse
Cooler Master HAF 932 Black Edition Cooler Master Havoc 
CPUGraphicsRAMHard Drive
i5-3210M  Intel HD Graphics 4000 Gskill 16GB 1600mhz  Crucial MX200 256GB 
Hard DriveOSOSMonitor
Seagate 320GB Ubuntu 16.04 Windows 10 1600x900 
  hide details  
Reply
post #125 of 9531
Quote:
Originally Posted by GrandDestroyer View Post

First of all thanks for the guide! Really helped making things a bit clearer. But I am still issues with overclocking my 2500k frown.gif
First of all my specs:
i5 2500k
ASRock Pro3 Gen3 (No LLC and fixed voltage)
XFX HD 6870
Corsair DDR3-12800 8 GB (9-9-9-24)
Corsair 500V V2 Builder series.
Cooler Master Hyper Evo 212
I can't get any overclock stable on a higher multiplier, after a while it will just drop to 33 as a multiplier and go back up to the setting i selected but this constantly switching will happen every minute or so after its first occurrence.
I tried setting the multiplier to 38, 40, 42, 45 and how higher I go how faster it will start with dropping to 33. On 45x it will drop after 5 minutes, while on 40 it can almost run 45 minutes before it starts dropping.
I have tried every option in the bios with power saving on or off, different power limits and even 1.4 voltage on 40x to see if it was the voltage. But nothing helped.
Things i have noticed:
Voltage will drop about 0.1 when multiplier goes to 33, so when i am on 1.2V with 40 multiplier it will become 1.1. On 45x it will drop from 1.3 to 1.2 or 1.35 to 1.25.
Its not thermal throttling as temps are around 65-70 degrees on 4.5 Ghz in the first 5 minutes of stress testing.
Even on 38 it will drop to 33 when stressing for 2-3 hours. So I am kinda out of options.
Only thing i haven't tried is setting the long power duriation to anything higher then 1 second. Could that be the cause?


Here are my settings at stock and the multi isn't jumping around. I will be playing with the overclock tomorrow so ill let you know if i run into a similar problem.

Ratio 33
Internal PLL disabled
Speedstep disabled
Core limit 250
Bclk 100
Spread spectrum disabled
Fixed voltage @ 1.20v
Dram voltage @ 1.499 w/ timings set
All other voltages on auto
C1E disabled
C3 Disabled
C6 Disabled
Package C-State support Auto
Throttling Enabled
Virtualization Disabled
No execute Disabled
LLC @ level 3
Z170 Build
(20 items)
 
Z68 Build
(20 items)
 
Lenovo T430
(14 items)
 
CPUMotherboardGraphicsGraphics
I7 6700K @ 4.5ghz  Gigabyte Z170x Gaming 6 XFX R9 290x 8GB XFX R9 290x 8GB 
RAMHard DriveHard DriveCooling
Gskill RipJaws V 16GB 3000mhz Samsung 850 EVO 250GB Seagate Barracuda 2TB EK-Supremacy EVO CPU Water Block 
CoolingCoolingCoolingCooling
EK R9 290X GPU Waterblocks EK-XRES 140 Revo D5 PWM Pump Alphacool NexXxoS 360mm ST30 Alphacool NexXxoS 240mm ST30 
CoolingCoolingOSMonitor
Alphacool NexXxoS 120mm ST30 Cooler Master Jetflo 120mm Fans Windows 10  LG 34UC88 
KeyboardPowerCaseMouse
Quickfire TK red switch Cooler Master V1000 MasterCase Pro 5 CM Storm Havoc 
CPUMotherboardGraphicsGraphics
I5 2500K @ 4.6ghz  ASRock Z68 Extreme 3 Gen 3 ASUS 7870 Ghz Edition ASUS 7870 Ghz Edition 
RAMHard DriveHard DriveOptical Drive
Gskill RipJaws X 16GB 1600mhz Seagate 2TB Seagate 320GB ASUS Burner 
CoolingCoolingCoolingOS
Cooler Master Eisberg 240L + 120mm Rad Koolance 3/8 x 1/2 Compression Fittings PrimoChill Advanced LRT Windows 7  
OSMonitorKeyboardPower
Ubuntu 12.04 ASUS 24" Cooler Master Quickfire TK  Cooler Master V1000 
CaseMouse
Cooler Master HAF 932 Black Edition Cooler Master Havoc 
CPUGraphicsRAMHard Drive
i5-3210M  Intel HD Graphics 4000 Gskill 16GB 1600mhz  Crucial MX200 256GB 
Hard DriveOSOSMonitor
Seagate 320GB Ubuntu 16.04 Windows 10 1600x900 
  hide details  
Reply
Z170 Build
(20 items)
 
Z68 Build
(20 items)
 
Lenovo T430
(14 items)
 
CPUMotherboardGraphicsGraphics
I7 6700K @ 4.5ghz  Gigabyte Z170x Gaming 6 XFX R9 290x 8GB XFX R9 290x 8GB 
RAMHard DriveHard DriveCooling
Gskill RipJaws V 16GB 3000mhz Samsung 850 EVO 250GB Seagate Barracuda 2TB EK-Supremacy EVO CPU Water Block 
CoolingCoolingCoolingCooling
EK R9 290X GPU Waterblocks EK-XRES 140 Revo D5 PWM Pump Alphacool NexXxoS 360mm ST30 Alphacool NexXxoS 240mm ST30 
CoolingCoolingOSMonitor
Alphacool NexXxoS 120mm ST30 Cooler Master Jetflo 120mm Fans Windows 10  LG 34UC88 
KeyboardPowerCaseMouse
Quickfire TK red switch Cooler Master V1000 MasterCase Pro 5 CM Storm Havoc 
CPUMotherboardGraphicsGraphics
I5 2500K @ 4.6ghz  ASRock Z68 Extreme 3 Gen 3 ASUS 7870 Ghz Edition ASUS 7870 Ghz Edition 
RAMHard DriveHard DriveOptical Drive
Gskill RipJaws X 16GB 1600mhz Seagate 2TB Seagate 320GB ASUS Burner 
CoolingCoolingCoolingOS
Cooler Master Eisberg 240L + 120mm Rad Koolance 3/8 x 1/2 Compression Fittings PrimoChill Advanced LRT Windows 7  
OSMonitorKeyboardPower
Ubuntu 12.04 ASUS 24" Cooler Master Quickfire TK  Cooler Master V1000 
CaseMouse
Cooler Master HAF 932 Black Edition Cooler Master Havoc 
CPUGraphicsRAMHard Drive
i5-3210M  Intel HD Graphics 4000 Gskill 16GB 1600mhz  Crucial MX200 256GB 
Hard DriveOSOSMonitor
Seagate 320GB Ubuntu 16.04 Windows 10 1600x900 
  hide details  
Reply
post #126 of 9531
Quote:
Originally Posted by Lucky 23 View Post

What cooler are you running?

CM Hyper 212 Plus. Seems to be working well. I used one like this on a c2d system I gave away to a friend. Not all that pretty, but it installed easily enough and is keeping things cool, and not expensive.

marty
post #127 of 9531
Hey I was wondering what settings I should use on Load line calibration? It's default level 5 but I have no idea what it does confused.gif
It's a computer
(15 items)
 
  
CPUMotherboardGraphicsGraphics
2500k 4.5ghz @1.35v Asrock Extreme 3 Gen 3 Asus GTX 470 725/1694 @1.025v EVGA GTS 450 900/1804 (PhysX) 
RAMHard DriveOptical DriveCooling
8gb Gskill 1600mhz 640gb, Seagate 1tb Spinpoint F3, Kingston 60gb SSD LG Combo Thermaltake SpinQ 
OSMonitorKeyboardPower
Win7 64bit Ultimate Acer X203H 1600x900 CM Storm Quickfire w/ Blues PC Power and Cooling 750watt Silencer MKII 
CaseMouseMouse Pad
Silverstone Raven RV02 Microsoft 1.1A Razer Goliathus 
  hide details  
Reply
It's a computer
(15 items)
 
  
CPUMotherboardGraphicsGraphics
2500k 4.5ghz @1.35v Asrock Extreme 3 Gen 3 Asus GTX 470 725/1694 @1.025v EVGA GTS 450 900/1804 (PhysX) 
RAMHard DriveOptical DriveCooling
8gb Gskill 1600mhz 640gb, Seagate 1tb Spinpoint F3, Kingston 60gb SSD LG Combo Thermaltake SpinQ 
OSMonitorKeyboardPower
Win7 64bit Ultimate Acer X203H 1600x900 CM Storm Quickfire w/ Blues PC Power and Cooling 750watt Silencer MKII 
CaseMouseMouse Pad
Silverstone Raven RV02 Microsoft 1.1A Razer Goliathus 
  hide details  
Reply
post #128 of 9531
Thread Starter 
Quote:
Originally Posted by Ghooble View Post

Hey I was wondering what settings I should use on Load line calibration? It's default level 5 but I have no idea what it does confused.gif
Quote:
Originally Posted by The Guide 
When your chip increases to max speed, the Vcore usually tends to drop down. This is known as Vdroop. If the Vcore drops down a bunch, that will lead to stability issues. To combat this, CPU LLC was made to offset this loss. Level 5 will net you the least compensation, and Level 1 the most. You want to find the setting that will get you the same Vcore that is says in BIOS during load in Windows as reported by CPUZ.

Level 1 seems to spike your Vcore up way high during load, so I do not recommend using that.

CPU Load-Line Calibration: Level 3 or Level 2 (whichever one will get you closest to BIOS Vcore)

It is used for compensating vCore when your CPU speed is maxed. Level 5 gives you the least compensation, Level 1 gives you the greatest.

You want to make use of it so that the vCore you set in the BIOS is what you actually get when you are stress testing. If you lose too much voltage, your computer might crash.
Edited by kennyparker1337 - 3/20/12 at 8:02pm
post #129 of 9531
Quote:
Originally Posted by Ghooble View Post

Hey I was wondering what settings I should use on Load line calibration? It's default level 5 but I have no idea what it does confused.gif

I suggest 2 or 3. Seems to be the most common LLC that's used on all 1155 socket boards.
^_^
(13 items)
 
   
CPUMotherboardGraphicsRAM
Intel 2600K ASRock Z68 EXTREME4 GEN3 Gigabyte Windforce 7970 OC Mushkin Enhanced Blackline 8GB (2 x 4GB) 
CoolingMonitorPowerCase
Noctua D14 Asus VG248QE Corsair TX 750 V2 Corsair 650D 
MouseMouse PadAudioAudio
G400, MX518, G500, G5, IMO 1.1, IME 3.0, Deatha... fUnC 1030, QCK+, QCK Heavy, PureTrak Talent Whi... X-Fi Titanium HD Sennheiser HD555 
CPUGraphicsRAMHard Drive
Intel i7 2.4GHz Intel HD 4000 8GB 256GB SSD 
Monitor
2880 x 1800 Retina 
  hide details  
Reply
^_^
(13 items)
 
   
CPUMotherboardGraphicsRAM
Intel 2600K ASRock Z68 EXTREME4 GEN3 Gigabyte Windforce 7970 OC Mushkin Enhanced Blackline 8GB (2 x 4GB) 
CoolingMonitorPowerCase
Noctua D14 Asus VG248QE Corsair TX 750 V2 Corsair 650D 
MouseMouse PadAudioAudio
G400, MX518, G500, G5, IMO 1.1, IME 3.0, Deatha... fUnC 1030, QCK+, QCK Heavy, PureTrak Talent Whi... X-Fi Titanium HD Sennheiser HD555 
CPUGraphicsRAMHard Drive
Intel i7 2.4GHz Intel HD 4000 8GB 256GB SSD 
Monitor
2880 x 1800 Retina 
  hide details  
Reply
post #130 of 9531
Quote:
Originally Posted by dmasteR View Post

I suggest 2 or 3. Seems to be the most common LLC that's used on all 1155 socket boards.
Quote:
Originally Posted by kennyparker1337 View Post

Quote:
Originally Posted by The Guide 
When your chip increases to max speed, the Vcore usually tends to drop down. This is known as Vdroop. If the Vcore drops down a bunch, that will lead to stability issues. To combat this, CPU LLC was made to offset this loss. Level 5 will net you the least compensation, and Level 1 the most. You want to find the setting that will get you the same Vcore that is says in BIOS during load in Windows as reported by CPUZ.
Level 1 seems to spike your Vcore up way high during load, so I do not recommend using that.
CPU Load-Line Calibration: Level 3 or Level 2 (whichever one will get you closest to BIOS Vcore)
It is used for compensating vCore when your CPU speed is maxed. Level 5 gives you the least compensation, Level 1 gives you the greatest.
You want to make use of it so that the vCore you set in the BIOS is what you actually get when you are stress testing. If you lose too much voltage, your computer might crash.

Thanks guys biggrin.gif +reps are definitely in order
It's a computer
(15 items)
 
  
CPUMotherboardGraphicsGraphics
2500k 4.5ghz @1.35v Asrock Extreme 3 Gen 3 Asus GTX 470 725/1694 @1.025v EVGA GTS 450 900/1804 (PhysX) 
RAMHard DriveOptical DriveCooling
8gb Gskill 1600mhz 640gb, Seagate 1tb Spinpoint F3, Kingston 60gb SSD LG Combo Thermaltake SpinQ 
OSMonitorKeyboardPower
Win7 64bit Ultimate Acer X203H 1600x900 CM Storm Quickfire w/ Blues PC Power and Cooling 750watt Silencer MKII 
CaseMouseMouse Pad
Silverstone Raven RV02 Microsoft 1.1A Razer Goliathus 
  hide details  
Reply
It's a computer
(15 items)
 
  
CPUMotherboardGraphicsGraphics
2500k 4.5ghz @1.35v Asrock Extreme 3 Gen 3 Asus GTX 470 725/1694 @1.025v EVGA GTS 450 900/1804 (PhysX) 
RAMHard DriveOptical DriveCooling
8gb Gskill 1600mhz 640gb, Seagate 1tb Spinpoint F3, Kingston 60gb SSD LG Combo Thermaltake SpinQ 
OSMonitorKeyboardPower
Win7 64bit Ultimate Acer X203H 1600x900 CM Storm Quickfire w/ Blues PC Power and Cooling 750watt Silencer MKII 
CaseMouseMouse Pad
Silverstone Raven RV02 Microsoft 1.1A Razer Goliathus 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel CPUs
Overclock.net › Forums › Intel › Intel CPUs › Complete Overclocking Guide: Sandy Bridge & Ivy Bridge | *ASRock Edition*