Overclock.net › Forums › Components › Monitors and Displays › CrossOver 27Q LED/LED-P, 27M LED, & 2720MDP GOLD LED Monitor Club
New Posts  All Forums:Forum Nav:

CrossOver 27Q LED/LED-P, 27M LED, & 2720MDP GOLD LED Monitor Club - Page 233

post #2321 of 6483
The blade uses the gold plastic bezel. It's not nicer at all. It's the same specs, but a new shell and some internal speakers.

The point of the crossover over the others (imo) is for dat metal bezel. Always go for that one, imo.
post #2322 of 6483
Quote:
Originally Posted by Queesy View Post

WOW that sucks!!!! So sorry for you bro.
Anyways, thanks descadent for giving us the heads up on the Crossover Blade.
I'm looking over the description right now and it cant figure out any noticeable differences despite it has a nicer and newer looking shell compared to the 27Q.

it has speakers... whoopty doo...and stand is different.
post #2323 of 6483
Quote:
Originally Posted by LC155 View Post

The blade uses the gold plastic bezel. It's not nicer at all. It's the same specs, but a new shell and some internal speakers.
The point of the crossover over the others (imo) is for dat metal bezel. Always go for that one, imo.

yes. it's not just metal bezel, it's the whole damn monitor that is metal. just so sexy
post #2324 of 6483
Quote:
Originally Posted by Descadent View Post

yes. it's not just metal bezel, it's the whole damn monitor that is metal. just so sexy

That same chasis the blade uses is used in the UK DGM rebrand. I tried it out for a bit.

That stand is woefully pathetic at keeping the monitor upright.
post #2325 of 6483
Quote:
Originally Posted by LC155 View Post

The point of the crossover over the others (imo) is for dat metal bezel. Always go for that one, imo.

I *just* got the Led-P because of the ability to do Portrait and the bezel - the p version has thinner bezels compared to the other korean ips monitors right?

I cant verify yet cuz i'm at work and my bro just signed for it tongue.gif dammit 4 more hours! I'm really really hoping i get lucky and get a 0 dead pixel and 0 back light bleeding.

The whole thing was wrapped in bubble wrap so thats kinda cool
post #2326 of 6483
Quote:
Originally Posted by jerrolds View Post

I *just* got the Led-P because of the ability to do Portrait and the bezel - the p version has thinner bezels compared to the other korean ips monitors right?
I cant verify yet cuz i'm at work and my bro just signed for it tongue.gif dammit 4 more hours! I'm really really hoping i get lucky and get a 0 dead pixel and 0 back light bleeding.
The whole thing was wrapped in bubble wrap so thats kinda cool

P or not, the 27Q LED has the thinnest bezels. It was practically as thin as my Dell bezels, so that's very good for multi monitor setups!
post #2327 of 6483
I just ordered my 27Q LED. wooot, I'm in the club!
post #2328 of 6483
After following this thread for some weeks I ordered a -P last tuesday from red-cap. Got the shipping notice 7h later and on thursday it arrvied in Germany..where it got stuck in customs until yesterday -.-

The picture is perfect, no dead or stuck pixels, no noticable backlight bleeding. I'm totally blown away biggrin.gif
The only fault is a slightly bend stand:

so the plastic cover doesn't really fit on it. I don't really care as I can't see the backside anyways.
I believe the monitor left the factory this way...the package and the double bubble-wrap around it were completly unharmed so it doenst seem to be some transportation damage.

I want to thank MenacingTuba for his color profile, it's perfect. ( http://www.overclock.net/t/1232496/crossover-27q-led-led-p-27m-led-2720mdp-gold-led-monitor-club/590#post_16946503 )

Does anyone have a 2560*1440 and a 1920*1020 (or smaller) monitor running with a GTX660ti or 670?
With the newest drivers the 6x0 cards should be able to switch into 2D power mode even if two displays with different resolutions are attached. Can anyone confirm that this will work, even if one display is running dual-link 2560*1440?
post #2329 of 6483
I'm curious about this too. What happens when you run different resolution monitors next to each other? I will have my Catleap/Shimian/Crossover sitting next to my S27A950D Samsung...
post #2330 of 6483
I have my crossover and a 1920x1200p monitor running off my 570 and the 570 downclocks itself to save power....

got two 670 sc 4gbs and two more crossovers on the way now.
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Monitors and Displays
Overclock.net › Forums › Components › Monitors and Displays › CrossOver 27Q LED/LED-P, 27M LED, & 2720MDP GOLD LED Monitor Club