Overclock.net › Forums › Intel › Intel Motherboards › [OFFICIAL] ROG Maximus V Owners Club
New Posts  All Forums:Forum Nav:

[OFFICIAL] ROG Maximus V Owners Club - Page 185

post #1841 of 4012
Wow wow wow stop it!!!!

Your temps are WAY too high. I run 4.5 @1.29v, (1.27v on the Sabertooth but I've set it now to 1.29 because I haven't tested it yet for stability). but some chips would need 1.31 or even 1.34v for 4.5Ghz, but there's no way you reach 96°C or even 80°+C at this voltage. This is just wrong. My temps are 59°C MAX on the highest core. I haven't checked the guide you posted but the procedure is more or less the same for all Asus boards, and you should be extremely careful with each setting.

1) What cooler do you use?

2) In the BIOS settings, DISABLE PLL Overvoltage. There is also an awful lot of tweaks that you must meticulously follow.

3) To reach a stable OC you must rn a Standard test in Prime 95 for AT LEAST 12 hours. 12 hours is stable. 16 hours is better. 24h is da bomb.
Before running a standard Prime 95 test, it is better to test by running custom-blend tests like the 1792 and the 1344 one for 15 minutes each. These are hyper-stressful tests, and they are a first indication on the stabiulity of your OC. If your OC cannot run 15/20 minutes of a 1792 custom blend test it won't run 12 hours of standard test. No need to let the custom tests run more than 20 minutes, it's completely normal it crashes after half an hour.

I'll come back with a template for an OC.

When you have a BSOD, check the error code.


BSOD codes for overclocking:

0x101 = increase vcore
0x124 = increase/decrease vcore or QPI/VTT...have to test to see which one it is
0x0A = unstable RAM/IMC, increase QPI first, if that doesn't work increase vcore
0x1E = increase vcore
0x3B = increase vcore
0x3D = increase vcore
0xD1 = QPI/VTT, increase/decrease as necessary, can also be unstable Ram, raise Ram voltage
0x9C = QPI/VTT most likely, but increasing vcore has helped in some instances
0x50 = RAM timings/Frequency or uncore multi unstable, increase RAM voltage or adjust QPI/VTT, or lower uncore if you're higher than 2x
0x109 = Not enough or too Much memory voltage
0x116 = Low IOH (NB) voltage, GPU issue (most common when running multi-GPU/overclocking GPU)
0x7E = Corrupted OS file, possibly from overclocking. Run sfc /scannow and chkdsk /r
post #1842 of 4012
thanks is water
post #1843 of 4012
Quote:
Originally Posted by Pieterbouw View Post

thanks is water

Did you do CPU Level Up/Auto OC?
 
"MSI GT70"
(15 items)
 
 
CPUGraphicsRAMHard Drive
Intel Core i7 4700MQ NVIDIA Geforce GTX 780M 32GB 1600MHz 128GB SSD Triple Raid 
Hard DriveHard DriveHard DriveOptical Drive
128GB SSD 128GB SSD 1TB  Blueray 
OSMonitor
Windows 8 Professional  17: 1920x1080 
  hide details  
Reply
 
"MSI GT70"
(15 items)
 
 
CPUGraphicsRAMHard Drive
Intel Core i7 4700MQ NVIDIA Geforce GTX 780M 32GB 1600MHz 128GB SSD Triple Raid 
Hard DriveHard DriveHard DriveOptical Drive
128GB SSD 128GB SSD 1TB  Blueray 
OSMonitor
Windows 8 Professional  17: 1920x1080 
  hide details  
Reply
post #1844 of 4012
Thread Starter 
Quote:
Originally Posted by DaGoat View Post

Wow wow wow stop it!!!!

Your temps are WAY too high. I run 4.5 @1.29v, (1.27v on the Sabertooth but I've set it now to 1.29 because I haven't tested it yet for stability). but some chips would need 1.31 or even 1.34v for 4.5Ghz, but there's no way you reach 96°C or even 80°+C at this voltage. This is just wrong. My temps are 59°C MAX on the highest core. I haven't checked the guide you posted but the procedure is more or less the same for all Asus boards, and you should be extremely careful with each setting.

1) What cooler do you use?

2) In the BIOS settings, DISABLE PLL Overvoltage. There is also an awful lot of tweaks that you must meticulously follow.

3) To reach a stable OC you must rn a Standard test in Prime 95 for AT LEAST 12 hours. 12 hours is stable. 16 hours is better. 24h is da bomb.
Before running a standard Prime 95 test, it is better to test by running custom-blend tests like the 1792 and the 1344 one for 15 minutes each. These are hyper-stressful tests, and they are a first indication on the stabiulity of your OC. If your OC cannot run 15/20 minutes of a 1792 custom blend test it won't run 12 hours of standard test. No need to let the custom tests run more than 20 minutes, it's completely normal it crashes after half an hour.

I'll come back with a template for an OC.

When you have a BSOD, check the error code.


BSOD codes for overclocking:

0x101 = increase vcore
0x124 = increase/decrease vcore or QPI/VTT...have to test to see which one it is
0x0A = unstable RAM/IMC, increase QPI first, if that doesn't work increase vcore
0x1E = increase vcore
0x3B = increase vcore
0x3D = increase vcore
0xD1 = QPI/VTT, increase/decrease as necessary, can also be unstable Ram, raise Ram voltage
0x9C = QPI/VTT most likely, but increasing vcore has helped in some instances
0x50 = RAM timings/Frequency or uncore multi unstable, increase RAM voltage or adjust QPI/VTT, or lower uncore if you're higher than 2x
0x109 = Not enough or too Much memory voltage
0x116 = Low IOH (NB) voltage, GPU issue (most common when running multi-GPU/overclocking GPU)
0x7E = Corrupted OS file, possibly from overclocking. Run sfc /scannow and chkdsk /r

I own a h80 with push pull gentle typhoons, I'm thinking I put the TIM on wrong. I'm going to disable the clock and order some new TIM tomorrow. after I'll be sure to follow your steps. Also whats the best TIM should I get?
Maximus V GENE
(15 items)
 
  
CPUMotherboardGraphicsRAM
Intel 3570k  Asus Maximus V GENE EVGA GTX 670 FTW 2GB No OC Samsung 8GB Low Voltage DDR3 
Hard DriveCoolingOSMonitor
Western Digital WD 1tb HDD H80 push/pull AP-15's Windows 8 Dell U2412M 
KeyboardPowerCaseMouse
Cooler Master QuickFire Rapid Cherry MX Reds SeaSonic X750 Silverstone TJ08-E Roccat Savu 
Mouse PadAudioAudio
XTRAC PADS Ripper XXL Beyerdynamic DT770 Pro 80 OHM's Klipsch ProMedia 2.1 
  hide details  
Reply
Maximus V GENE
(15 items)
 
  
CPUMotherboardGraphicsRAM
Intel 3570k  Asus Maximus V GENE EVGA GTX 670 FTW 2GB No OC Samsung 8GB Low Voltage DDR3 
Hard DriveCoolingOSMonitor
Western Digital WD 1tb HDD H80 push/pull AP-15's Windows 8 Dell U2412M 
KeyboardPowerCaseMouse
Cooler Master QuickFire Rapid Cherry MX Reds SeaSonic X750 Silverstone TJ08-E Roccat Savu 
Mouse PadAudioAudio
XTRAC PADS Ripper XXL Beyerdynamic DT770 Pro 80 OHM's Klipsch ProMedia 2.1 
  hide details  
Reply
post #1845 of 4012
Here is a basic template:

When not indicated, leave at default.

EXTREME TWEAKING TAB:

CPU LVL UP: DISABLED
AI OC TUNER: XMP
XMP: PROFILE 1
BCLK: 100.00 (NEVER mess with BCLK for starters. ALWAYS leave it to 100.00)
Turbo Ratio: By ALL CORES
By All Cores: 45 (for a 4.5Ghz OC)
PLL OVERVOLTAGE; DISABLED (VERY important)
Mem Freq: your memory (DDR3 1600?)
Extreme Tweaking; DISABLED
SPI; DISABLED
EPU: DISABLED

CPU Power:
CPU Ratio: AUTO
Intel Speedstep: ENABLED
Turbo Mode: ENABLED

DIGI POWER CONTROL:
CPU Load Line Calibration: ULTRA HIGH

CPU V Frequency: MANUAL
CPU Fixed Frequency: 350

CPU Power Phase: Extreme
CPU Current: 140%

Extreme OC: DISABLED
CPU Voltage: Manual
CPU Manual Voltage: 1.30v (For starters, as a test)
CPU Spread Spectrum: DISABLED

ADVANCED TAB

CPU Config:


Intel Thermal Monitor: ENABLED
Active Processor Cores: ALL


This is just a starters. There is a lot of fine tuning afterwards, with the VCCIO, VCCSA, PPL, and so on. thumb.gif

///
EDIT: Added CPU Spread Spectrum and changed CPU Level Up.
Edited by DaGoat - 1/30/13 at 4:25am
post #1846 of 4012
I have a H80 with stock fans, but I have a 2500K and it is said that Sandy Bridge is less hot than IB. I'd say you should get 69°C max on all cores. (10°C more than I). It's just a wild guess. If it runs hotter it is not very problematic. But I'll want to have it below the 80°C limit, that's for sure.

It's not that it isn't safe - CPUs can run "safe" @ 95°C +,without problems, it is just preferable to have less. And your chip will last longer.
post #1847 of 4012
Thread Starter 
Quote:
Originally Posted by DaGoat View Post

Here is a basic template:
Warning: Spoiler! (Click to show)
When not indicated, leave at default.

EXTREME TWEAKING TAB:

CPU LVL UP: AUTO
AI OC TUNER: XMP
XMP: PROFILE 1
BCLK: 100.00 (NEVER mess with BCLK for starters. ALWAYS leave it to 100.00)
Turbo Ratio: By ALL CORES
By All Cores: 45 (for a 4.5Ghz OC)
PLL OVERVOLTAGE; DISABLED (VERY important)
Mem Freq: your memory (DDR3 1600?)
Extreme Tweaking; DISABLED
SPI; DISABLED
EPU: DISABLED

CPU Power:
CPU Ratio: AUTO
Intel Speedstep: ENABLED
Turbo Mode: ENABLED

DIGI POWER CONTROL:
CPU Load Line Calibration: ULTRA HIGH

CPU V Frequency: MANUAL
CPU Fixed Frequency: 350

CPU Power Phase: Extreme
CPU Current: 140%

Extreme OC: DISABLED
CPU Voltage: Manual
CPU Manual Voltage: 1.30v (For starters, as a test)

ADVANCED TAB


CPU Config:


Intel Thermal Monitor: ENABLED
Active Processor Cores: ALL


This is just a starters. There is a lot of fine tuning afterwards, with the VCCIO, VCCSA, PPL, and so on. thumb.gif

You are absolutely fantastic! Thank you! I'm planning on buying this Thermal Paste I will hopefully be able to overclock in a week.
Maximus V GENE
(15 items)
 
  
CPUMotherboardGraphicsRAM
Intel 3570k  Asus Maximus V GENE EVGA GTX 670 FTW 2GB No OC Samsung 8GB Low Voltage DDR3 
Hard DriveCoolingOSMonitor
Western Digital WD 1tb HDD H80 push/pull AP-15's Windows 8 Dell U2412M 
KeyboardPowerCaseMouse
Cooler Master QuickFire Rapid Cherry MX Reds SeaSonic X750 Silverstone TJ08-E Roccat Savu 
Mouse PadAudioAudio
XTRAC PADS Ripper XXL Beyerdynamic DT770 Pro 80 OHM's Klipsch ProMedia 2.1 
  hide details  
Reply
Maximus V GENE
(15 items)
 
  
CPUMotherboardGraphicsRAM
Intel 3570k  Asus Maximus V GENE EVGA GTX 670 FTW 2GB No OC Samsung 8GB Low Voltage DDR3 
Hard DriveCoolingOSMonitor
Western Digital WD 1tb HDD H80 push/pull AP-15's Windows 8 Dell U2412M 
KeyboardPowerCaseMouse
Cooler Master QuickFire Rapid Cherry MX Reds SeaSonic X750 Silverstone TJ08-E Roccat Savu 
Mouse PadAudioAudio
XTRAC PADS Ripper XXL Beyerdynamic DT770 Pro 80 OHM's Klipsch ProMedia 2.1 
  hide details  
Reply
post #1848 of 4012
Starting to tweak my platform, even though I have no GPU.... It makes it harder without one... MVE is doing a great job....


http://valid.canardpc.com/2673468

LEAD Technologies Inc. V1.01

LEAD Technologies Inc. V1.01
 
"MSI GT70"
(15 items)
 
 
CPUGraphicsRAMHard Drive
Intel Core i7 4700MQ NVIDIA Geforce GTX 780M 32GB 1600MHz 128GB SSD Triple Raid 
Hard DriveHard DriveHard DriveOptical Drive
128GB SSD 128GB SSD 1TB  Blueray 
OSMonitor
Windows 8 Professional  17: 1920x1080 
  hide details  
Reply
 
"MSI GT70"
(15 items)
 
 
CPUGraphicsRAMHard Drive
Intel Core i7 4700MQ NVIDIA Geforce GTX 780M 32GB 1600MHz 128GB SSD Triple Raid 
Hard DriveHard DriveHard DriveOptical Drive
128GB SSD 128GB SSD 1TB  Blueray 
OSMonitor
Windows 8 Professional  17: 1920x1080 
  hide details  
Reply
post #1849 of 4012
Sorry for the CPU Level Up mistake. Hope you didn't encounter a Boot Loop. It's DISABLED. Not AUTO. doh.gif

I've double-checked all the other settings, everything's fine.

I got this exact thermal Paste. Arctic Silver. It was da bomb when I bought it back in 2011, nowadays it's still excellent but I've been told there is much better.

Like The IC Diamond 24, pure 24 carat Diamond (exists in 7 carat) ,or Coolaboratoy Liquid Ultra
post #1850 of 4012
Quote:
Originally Posted by PatrickCrowely View Post

Starting to tweak my platform, even though I have no GPU.... It makes it harder without one... MVE is doing a great job....


http://valid.canardpc.com/2673468

LEAD Technologies Inc. V1.01

LEAD Technologies Inc. V1.01

Great 5Ghz OC, now you must run Prime 95 during at least 12 hours to see if it's stable. it's relativiely easy to squeeze out a 5Ghz OC with a good chip, it's much hareder do get it stable. So far you've ran Prime95 for a few minutes so it's not a validated stable OC yet. Hope it will do! thumb.gif
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel Motherboards
Overclock.net › Forums › Intel › Intel Motherboards › [OFFICIAL] ROG Maximus V Owners Club