Corsair 800D "The Secret of the Ooze" Build Thread - Page 20

Okay i ran some tubing last night and here is how i have it set up -



The only thing left to do is figure out where to send the discharge feed off the pump.

I can send it to 1 of the gpu's -

Top gpu is fed from the rear rad

Bottom gpu is acting as a drain loop(lowest Point)

I can send it to the cpu IN but then where do i send the additional feed coming off the rear rad ?

I also have a Bitspower ram water block i can use if that will make configuring this loop easier.

If i bring the pump discharge to the bottom video card its going to be an ugly bend so i am trying to avoid that.


Can i bring the pump discharge to the side of the top gpu ?

I keep reading that the loop order won't matter since the water temp will balance out so as of right now that looks like the cleanest way to route the pump discharge.

I am once again changing my mind on what reservoir i will be using on this build!

I bought a Bitspower Water Tank Z-Multi 150 - POM a while back so i have decided to mount it to the top of my D5 pump.



I will be using this fitting to connect it to the top inlet port on the Bitspower pump top -



This res has 3 ports on the bottom and 1 on top so it seems like the best way to configure it is the following -

Use the single port side to connect the res to the pump.

Use the 3 ported side for a return line from my top 360 rad and also use a port to fill the res.

Does this all make sense ?

Thanks bro.

The res already has a silver aqua pipe and anti-cyclone fitting in it but i will buy both in that Bitspower matte black because i prefer the look of it.

The best place to mount the Bitspower flow indicator seems to be above the top gpu left output. I did a few dry fits with different lengths of tubing but i don't like the way the tubing leans back due to the weight so i found a solution -



I can mount this to the top left gpu port then thread the Bitspower flow indicator right in for much added stability.

I re located my Intel 520 series 240 gig SSD to this location a few weeks ago but i am going to move it back to the hot swap HD bay and replace it with this SSD -

It will provide an additional 240 gigs of space for future games and match the UV light show that will be going on.




Edited by nyk20z3 - 10/10/12 at 12:27pm

Ordered my custom PSU plate cover and here is how it works -

http://www.youtube.com/watch?feature=player_embedded&v=mMEEVpRgLjA#!

Tons of other things ordered as well(some for function and some for flash) -

Bitspower Premium Male G1/4" Matt Black Aqua-Pipe I Fitting - This will replace the silver aqua pipe that comes stock in the Bitspower 150 Z-Multi water tank.



Bitspower G1/4" Anti-Cyclone Adapter - Black Matte Finish - This will replace the silver anti-cyclone adapter that comes stock in the Bitspower 150 Z-Multi water tank.



Bitspower UV Mesh Radguard 120 (1 x 120mm) - UV Green X3 - These will cover and protect my 360 interior mounted roof radiator and also add a nice visual effect.



(UN)Designs Pump Z3-Bracket (for Laing D4/D5/DDC Pumps) & 140mm Fans - Black - I currently have the deep blue version but i feel the black version will blend it better.



Enzotech Male to Male G 1/4 Threaded Coupler - Matte Black X2 - I need 1 to mount the Bitspower water tank to the pump and 1 to thread the Bitspower flow indicator in to a Enzotech thread adapter.



Enzotech Male to Female G 1/4 Threaded Adapter - Matte Black - This will thread directly in to 1 of my top GPU ports to add some stability to the Bitspower flow indicator that will be threaded in to it.



Enzotech Male to Female G 1/4 Threaded Extender - Matte Black - I am using this because the discharge OUT port i am using on the pump will sit to close to the Bitspower water tank when mounted. I will have more space to work with now after i thread a 90 degree rotary barb in to this.



ENZOTECH BSLI-1 Fittings Package for SLI Setups - This will add another bridge to the video cards for added stability and flow.



8-Pin (EPS12V) Extension Cable 12 Inches - Sleeved in UV green and the female connecter will be UV green as well.

24-Pin (EPS12V) Extension Cable 12 Inches - Sleeved in UV green and the female connecter will be UV green as well.

BitFenix 3-pin to 3 x 3-pin Fan Adapter Cable 60cm - Black Sleeve X2 - I needed a 3 pin set so i can send all my 3 pin fan cable extensions directly to the fan controller for a cleaner look.

Mayhems Dye - 10ml UV Yellow/Green - I plan on adding a few drops to enhance the Mayhems UV green concentrate i will be using.



Mod/Smart Dual LED - Pre-wired with 4-Pin Connector 3mm - Blue X2 - This will be sleeved in UV green and replace the current LED's plugged in to my Raystorm cpu block.