Overclock.net › Forums › Graphics Cards › NVIDIA › GTX 600 Series Unlocked Voltage Bios' downloads and tools.
New Posts  All Forums:Forum Nav:

GTX 600 Series Unlocked Voltage Bios' downloads and tools. - Page 545

post #5441 of 7933
Quote:
Originally Posted by hamzta09 View Post

The KGB automaticly raises the Powerlimit to 150% and voltage to 1.875 something and boost to 121 something.

I raised powertarget to 120% in afterburner, and then it stays at 1150-1202, but even then the fps is lower than with 1097 lol.
Again are you hitting power limit ceiling , what doe max power at point it drops down.
try raising power target more . After a power limit change i would recommend first running at 100% and see if any throttling and if so amount, then raise power limiter and see how it improves .

The voltage should show 1.212 about as 1.187v is set in bios but boosts will raise it a few steps .

Was this your bios modified or someone else ?
desktop
(10 items)
 
  
CPUMotherboardGraphicsRAM
Intel i5-3570k Asus PZ77 v-Pro MSI 970 Gaming 4G Crucial Ballistix Tactical Tracer 8GB 
Hard DriveHard DriveCoolingOS
WD Black WD5002AALX 500GB 7200 RPM 32MB Cache ... Samsung 850evo 500GB SATA 6.0Gb/s CM Hyper 212evo Win7 64bit Pro SP1 
PowerCase
Corsair TX650 V2 650W Corsair 500R 
  hide details  
Reply
desktop
(10 items)
 
  
CPUMotherboardGraphicsRAM
Intel i5-3570k Asus PZ77 v-Pro MSI 970 Gaming 4G Crucial Ballistix Tactical Tracer 8GB 
Hard DriveHard DriveCoolingOS
WD Black WD5002AALX 500GB 7200 RPM 32MB Cache ... Samsung 850evo 500GB SATA 6.0Gb/s CM Hyper 212evo Win7 64bit Pro SP1 
PowerCase
Corsair TX650 V2 650W Corsair 500R 
  hide details  
Reply
post #5442 of 7933
Quote:
Originally Posted by Edkiefer View Post

Again are you hitting power limit ceiling , what doe max power at point it drops down.
try raising power target more . After a power limit change i would recommend first running at 100% and see if any throttling and if so amount, then raise power limiter and see how it improves .

The voltage should show 1.212 about as 1.187v is set in bios but boosts will raise it a few steps .

Was this your bios modified or someone else ?

My bios, modified via KGBs default settings.

At stock powertarget it throttles like mad yes. It goes from 1050 to 1202 and anywhere between.
post #5443 of 7933
Will there be increased performance when increasing the max boost table?
post #5444 of 7933

Could be, its a lot of figuring out what your card likes and how it stays cooled

post #5445 of 7933
Quote:
Originally Posted by kaneandtaker View Post

Will there be increased performance when increasing the max boost table?
How do you mean?

Quote:
Originally Posted by YounGMessiah View Post

Could be, its a lot of figuring out what your card likes and how it stays cooled
My card is air cooled and runs at 60-65c during gaming most of the time.
post #5446 of 7933

My comment was to kaneandtaker :P

post #5447 of 7933
What would the effect be of changing the Def (mW) and not just the Max (mW) settings in bios?
post #5448 of 7933

Your power percent would go down, but the amount of power you were actually drawing would be the same.  Drawing 100W with 150W set as the default would show 66% power, but if you change the default to 200W that same 100W would then show 50% power.  So no effect, really.  You'd still hit the limit at the same actual power draw, unless you increase the max.

post #5449 of 7933
Hmm. Ok. Right now I have it hovering around 1179-1189 Mhz when boosting, with a maximum boost of 1280mhz. I would like to get it up to around 1202-1215mhz in boost, without it throttling. I have tweaked the bios quite a bit back and forth, to try to achieve a decent clock without it starting to throttle. Its tricky since I run two of these cards in sli, and heat tend to be a bit high on the top card.
post #5450 of 7933
Ok so why wont unigine heaven work? Doesnt start, no matter how many times I press start or which settings I have. Ive reinstalled it twice now.

Ok so magically it works now.

At 132% powertarget, the core is glued to 1202, which is good.
67-68c at 89% fanspeed. Nice and quiet.

No driver crashes or anything yet.


Wow I get some really bad scores in heaven now


Nvm, I get reasonable scores, raised mem to +250.



Found another thread where people bench their 670/680s in 4.0, a guy with 1200 core/6500 mem got 951 score so Im good I guess.
Edited by hamzta09 - 5/16/13 at 8:57pm
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: NVIDIA
Overclock.net › Forums › Graphics Cards › NVIDIA › GTX 600 Series Unlocked Voltage Bios' downloads and tools.