Overclock.net › Forums › Intel › Intel CPUs › [Official] Delidded Club / Guide
New Posts  All Forums:Forum Nav:

[Official] Delidded Club / Guide - Page 184

post #1831 of 33821
Congrats Brother!
post #1832 of 33821
Quote:
Originally Posted by VonDutch View Post

first ...gratz! thumb.gif
"I used the entire syringe of Liquid Pro on the processor die"
thats prolly to much, you dont want it to run out from between the die and ihs, by the pressure,
you can use the seringe to suck some away again..
i used mine to do all sides, die, underside ihs, on ihs and base plate cooler,
all very thin layers
this weekend i did 2 vid cards with it, 1 card twice,
which needed a thick(er) layer because of poor contact, and still have some left smile.gif
if you run prime 30-40min, thats about the temps you get,
it will go up a bit more after hours run, but not much.. 3-5C max
dont have prime with 4.5ghz,
this is 4.7ghz, to compare temps with,

it stayed under 65C after 30 min prime

My readings at a little higher room temperature is 57C, 70C, 68C, 71C! Notice core 2, 3 and 4, pretty darn even! In the future if for some reason I need to separate the IHS from the processor die, how difficult will it be to wipe off all LP?

Also how much better should my temps be going from a Zalman heatsink with a 92mm fan versus an EK Supremacy, 2x EK-FC480GTX blocks, two D5's in serial using two 560 radiators running GT15's at 1850rpms (check build log below)?


Quote:
Originally Posted by Silkworm75 View Post

Systemlord, hope you save stock TIM. You might need it later. And good work

I don't understand what you mean, why do I need the stock TIM?
post #1833 of 33821
Thread Starter 
Ohh boy time to write lol. tongue.gif
Quote:
Originally Posted by neopunx View Post

1000 will be fine, you probably wont see any gains with 2000 grit. Mine was an impulse buy, and then my OCD kicked in and I had to make it look like gold.
Edit: Meant to do this before. REP + to Valgaur. You might not be the first delidder, but you gave us a home.

That really means a lot and I thank you for that I really want this place to be very informative but lax unlike some places were you can only posts results and that's about it. I hope everyone is all enjoying it so far and if so then GOOD! if not then let me know and we can make *magic* happen tongue.gif

I also really really like you sig for the delidded crew lol. You should PM me the code line and we can ask members on here what they think! thumb.gif
Quote:
Originally Posted by neopunx View Post

I wonder how many people have been able to acheive a 5.5 ghz on the 3770k on just air/water. I havent seen any others out there, except for our members.

So far yes me and VonDutch are the only people to get this high...(CPU frequency wise that is....you silly peoples you! rolleyes.gif ) on just air and H2O. Everyone else has been resorting to DICE or Ln2 to get beyond on...BUT I will hopefully be getting a DICE pot soon along with a Ln2 pot later on. I plan on going to the next Ln2 event with the HWbot group and either benching Little Franky until I max him out or until he gets to cold to want to.
Quote:
Originally Posted by PCWargamer View Post

From what I have read, you get no temp gains from lapping beyond 800 grit, so 1000 will be fine and more than enough.

Sweet....but what about shine? I kinda want it to look pretty....lol yes I'm ADHD and OCD. Bad combo I know biggrin.gif
Quote:
Originally Posted by PCWargamer View Post

Yep. The delidding crew rules with top OC on air/water! thumb.gif
Are you still working on your 5.5 neopunx? I think you are real close.

He better be!!!
Quote:
Originally Posted by neopunx View Post

^ This is also what I use ^
@ PCWargamer - Yes, althoguh I am pulling 24 hour duty as we write, so I have to wait for another 14 hours and 30 minutes before I can again try to lay waste to the current records!!!! medieval.gif

I expect good results!!!! also if you can't afford a dead chip....don't risk it. (I can't and went for it but I knew the risks and had everything plotted out so think carefully about it. the vcore jump is crazy this time around.)
Quote:
Originally Posted by Silkworm75 View Post

Test your cpu and make sure it works the way it should before going under the knife. It would suck to find out you delid a defective cpu. Murphy's law

I completely agree with this guys we NEED to make sure stuff works before saying meh i'll make it better my way.

FURTHERMORE ALL RMA INFORMATION WILL NOT BE TOLERATED IF IT IS POSTED ON HERE, THIS IS DUE TO AVOIDING GETTING CAUGHT WITH OUR WAY OF RETURNING OUR ACTUAL CHIPS AND SUCH. TO LET US KNOW DO US ALL A FAVOR AND PM ME VALGAUR PERSONALLY LETTING ME KNOW ALL THE INFO AND I'LL GET IT OUT PROPERLY!!! YOUR COOPERATION IS VERY APPRECIATED! thumb.gif
Quote:
Originally Posted by Systemlord View Post

Well I'm still here after the delidding process, success! Using a double sided paper thin blade (strange cutouts in center of blade) I remove all of the black glue and could believe how easily it wipe away using just my finger nail, I used the entire syringe of Liquid Pro on the processor die. I hope that didn't harm my results, I used MX4 on top of the IHS and my air cooler until the middle of next month when I install my Supremacy together with my ultra high-end water cooling loop..
My ambient temps before delidding was between 22C, my ambient temps at the time of the Prime 95 test picture below after delidding is about 21C, did using the entire syringe of Liquid Pro on the die screw with my results? I mean how do you compare 10 minutes of Prime 95 with 25 hours? I will try to create the environment of when I tested before delidding.

What cooler are you running at the moment? if it's a custom WC kit...then those temps arent right unless you have a CPU and GPU on the same loop.



Okay now for my post lol. I sadly can't lap my IHS yet or even do my LP and IX review yet either. I am going to wait until I get this other 3770K to delid and then test on both his first then mine so i can just let it run for about 7 months without changing anything. Sorry to delay it more but it MIGHT be sometime this week.

Anyways I'm glad that everyone is enjoying the club and hope to see more success stories and even better information than usual!! cheers.gif
post #1834 of 33821
Quote:
Originally Posted by Systemlord View Post

My readings at a little higher room temperature is 57C, 70C, 68C, 71C! Notice core 2, 3 and 4, pretty darn even! In the future if for some reason I need to separate the IHS from the processor die, how difficult will it be to wipe off all LP?
Also how much better should my temps be going from a Zalman heatsink with a 92mm fan versus an EK Supremacy, 2x EK-FC480GTX blocks, two D5's in serial using two 560 radiators running GT15's at 1850rpms (check build log below)?

yea, thats gonna improve your temps, of course i cant say how much,
what zalman cooler are you using now?

we dont have any good data yet, how LP will clean after, lets say a year, under the hood..lol
my guess is, within a half year, should still be easy clean, if you order new, you might consider
liquid ultra, its almost as good as pro, we have members with good results in here,
but its easier to clean..

the difference in core temps you have,14C, are a bit to much if you ask me,
thats what i had before delid, 10-15C between hottest and coolest core,
now i have a difference about 5-6C max between hottest /coolest core, under load,
thats ok tho, one core they call the sleepy core, its just a lazy one if you ask me ..lol
BamBam
(17 items)
 
Pebbles
(14 items)
 
 
CPUMotherboardGraphicsRAM
amd 8350 my kids rig :) Gigabyte 990fxa-ud3 Gigabyte 7970 windforce Corsair Vengeance CMZ8GX3M2A1600C9 
Hard DriveHard DriveCoolingOS
500gb OZC vertex 4  Scythe Mugen 3 rev b windows 8.1 
MonitorKeyboardPowerCase
acer 23 inch logitech G510 XFX ProSeries 750W XXX Edition Cooler Master CM 690 II 
MouseAudio
dell  Logitech X-530 
  hide details  
Reply
BamBam
(17 items)
 
Pebbles
(14 items)
 
 
CPUMotherboardGraphicsRAM
amd 8350 my kids rig :) Gigabyte 990fxa-ud3 Gigabyte 7970 windforce Corsair Vengeance CMZ8GX3M2A1600C9 
Hard DriveHard DriveCoolingOS
500gb OZC vertex 4  Scythe Mugen 3 rev b windows 8.1 
MonitorKeyboardPowerCase
acer 23 inch logitech G510 XFX ProSeries 750W XXX Edition Cooler Master CM 690 II 
MouseAudio
dell  Logitech X-530 
  hide details  
Reply
post #1835 of 33821
Thread Starter 
Quote:
Originally Posted by Systemlord View Post

My readings at a little higher room temperature is 57C, 70C, 68C, 71C! Notice core 2, 3 and 4, pretty darn even! In the future if for some reason I need to separate the IHS from the processor die, how difficult will it be to wipe off all LP?
Also how much better should my temps be going from a Zalman heatsink with a 92mm fan versus an EK Supremacy, 2x EK-FC480GTX blocks, two D5's in serial using two 560 radiators running GT15's at 1850rpms (check build log below)?
I don't understand what you mean, why do I need the stock TIM?

HA your temps will go to the 50-40 range i bet....your gonna own on temps man. especially if you rig up a passive DICE setup in your case where you have a container of Dry Ice (DICE fr those who don't know) ((just sayin)) and then let the cool air build up and let your rads pump that nice cold air through and super chill your computer to close to the 10-15C range i bet. shoo i'd even say the 5-10C range when idle and such things! wink.gif
post #1836 of 33821
Thread Starter 
Quote:
Originally Posted by VonDutch View Post

yea, thats gonna improve your temps, of course i cant say how much,
what zalman cooler are you using now?
we dont have any good data yet, how LP will clean after, lets say a year, under the hood..lol
my guess is, within a half year, should still be easy clean, if you order new, you might consider
liquid ultra, its almost as good as pro, we have members with good results in here,
but its easier to clean..
the difference in core temps you have,14C, are a bit to much if you ask me,
thats what i had before delid, 10-15C between hottest and coolest core,
now i have a difference about 5-6C max between hottest /coolest core, under load,
thats ok tho, one core they call the sleepy core, its just a lazy one if you ask me ..lol

Theres a way to turn those off....give me a bit to remember how...i just did it to....

HAHA found it!

http://www.coderbag.com/Programming-C/Disable-CPU-Core-Parking-Utility

click the executable file link not the source code.
Edited by Valgaur - 10/29/12 at 2:01am
post #1837 of 33821
I'm running a Zalman CNPS9500A LED at max fan speed without speed controller (2500rpms in BIOS), I will be using IX under my Supremacy. Remember that I'm using the iGPU so you would expect my temps to drop further, right?
post #1838 of 33821
Thread Starter 
Quote:
Originally Posted by Systemlord View Post

I'm running a Zalman CNPS9500A LED at max fan speed without speed controller (2500rpms in BIOS), I will be using IX under my Supremacy. Remember that I'm using the iGPU so you would expect my temps to drop further, right?

if your using the chip's graphics then you dont need 2 560 rads.......one thick 560 will do very nicely. but it is your build remember you can't get colder than ambient temps.
post #1839 of 33821
If i have a contact problem between die and ihs, do you think lapping the IHS lip that contacts the PCB would help any? Just a thought i read on another forum.
Pure Dark TJ07
(19 items)
 
  
CPUMotherboardGraphicsRAM
i7-4790K@4.8Ghz Gigabyte Z87X-OC Inno3D GTX 1080 iChiLL x3 TeamXtreem 8GB 2666C11 
Hard DriveHard DriveCoolingCooling
Samsung 840 Pro 128Gb WD Red 3TB XSPC Raystorm ThermoChill PA120.3 - 3xAP15  
CoolingOSMonitorKeyboard
Swiftech MCP655V - EK Top Windows 10 Pro x64 Samsung S27A850D (2560x1440) Ducky Shine / MX Red 
PowerCaseMouseAudio
Corsair AX850 TJ07 Full Matte Black (Modded) Logitech G900 Chaos Spectrum Asus Xonar Essence STX 
Audio
Εpoz Aktimate Mini on IsoAcoustics 
  hide details  
Reply
Pure Dark TJ07
(19 items)
 
  
CPUMotherboardGraphicsRAM
i7-4790K@4.8Ghz Gigabyte Z87X-OC Inno3D GTX 1080 iChiLL x3 TeamXtreem 8GB 2666C11 
Hard DriveHard DriveCoolingCooling
Samsung 840 Pro 128Gb WD Red 3TB XSPC Raystorm ThermoChill PA120.3 - 3xAP15  
CoolingOSMonitorKeyboard
Swiftech MCP655V - EK Top Windows 10 Pro x64 Samsung S27A850D (2560x1440) Ducky Shine / MX Red 
PowerCaseMouseAudio
Corsair AX850 TJ07 Full Matte Black (Modded) Logitech G900 Chaos Spectrum Asus Xonar Essence STX 
Audio
Εpoz Aktimate Mini on IsoAcoustics 
  hide details  
Reply
post #1840 of 33821
Quote:
Originally Posted by Valgaur View Post

Theres a way to turn those off....give me a bit to remember how...i just did it to....
HAHA found it!
http://www.coderbag.com/Programming-C/Disable-CPU-Core-Parking-Utility
click the executable file link not the source code.

did you try, or anyone else?
and noticed the temp difference was gone after?
BamBam
(17 items)
 
Pebbles
(14 items)
 
 
CPUMotherboardGraphicsRAM
amd 8350 my kids rig :) Gigabyte 990fxa-ud3 Gigabyte 7970 windforce Corsair Vengeance CMZ8GX3M2A1600C9 
Hard DriveHard DriveCoolingOS
500gb OZC vertex 4  Scythe Mugen 3 rev b windows 8.1 
MonitorKeyboardPowerCase
acer 23 inch logitech G510 XFX ProSeries 750W XXX Edition Cooler Master CM 690 II 
MouseAudio
dell  Logitech X-530 
  hide details  
Reply
BamBam
(17 items)
 
Pebbles
(14 items)
 
 
CPUMotherboardGraphicsRAM
amd 8350 my kids rig :) Gigabyte 990fxa-ud3 Gigabyte 7970 windforce Corsair Vengeance CMZ8GX3M2A1600C9 
Hard DriveHard DriveCoolingOS
500gb OZC vertex 4  Scythe Mugen 3 rev b windows 8.1 
MonitorKeyboardPowerCase
acer 23 inch logitech G510 XFX ProSeries 750W XXX Edition Cooler Master CM 690 II 
MouseAudio
dell  Logitech X-530 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel CPUs
Overclock.net › Forums › Intel › Intel CPUs › [Official] Delidded Club / Guide