Overclock.net › Forums › Intel › Intel CPUs › [Official] Delidded Club / Guide
New Posts  All Forums:Forum Nav:

[Official] Delidded Club / Guide - Page 750

post #7491 of 33576
Quote:
Originally Posted by VonDutch View Post

yea, i always run Turbo, give a slight vdroop,
was just wondering this morning about the extreme setting,
and why i should not use it, it did bring down offset by 0.020V it seems,
no change in temps looks like..just added some snapshots on that post ..

yeah, it lowers the offset, because it brings the base voltage higher wink.gif
temps looks same tho, maybe try running IBT in Max Mode for 5 runs and compare then?

I also keep CPu-Z open and look at vcore closely, it drops down to the lowest level the moment when 100% load on CPU is introduced (in max mode it will take a while to load up all memory with data) then it flattens at slightly higher level and occasionally only dips down to that "bottom under load" level. if it is stable throughout the test with no WHEA (double check with Cine) the such "bottom under load" voltage is the least your chip needs to run at such clocks, no matter if you use fixed vcore or different offsets - use it as a basis for quickly re-stabilizing CPU at same clock with different settings, it helps.
post #7492 of 33576
Quote:
Originally Posted by feniks View Post

yeah, it lowers the offset, because it brings the base voltage higher wink.gif
temps looks same tho, maybe try running IBT in Max Mode for 5 runs and compare then?
I also keep CPu-Z open and look at vcore closely, it drops down to the lowest level the moment when 100% load on CPU is introduced (in max mode it will take a while to load up all memory with data) then it flattens at slightly higher level and occasionally only dips down to that "bottom under load" level. if it is stable throughout the test with no WHEA (double check with Cine) the such "bottom under load" voltage is the least your chip needs to run at such clocks, no matter if you use fixed vcore or different offsets - use it as a basis for quickly re-stabilizing CPU at same clock with different settings, it helps.

thanks,
repforyou smile.gif
you mentioned,

"Extreme LLC will not cause vdroop, but it WILL overshoot vcore under full load"

does it really matter if my vcore is about 1.3V, and it overshoots under load?
lets say it overshoots by 0.010V..

no wheas during cinebench, ran it 2x to make sure,
i always start with cinebench with new oc's, it only takes a minute orso,
and it shows whea errors very fast,
or it just stops working, like with the 0.025V offset i used just now..

will do some max mode testing later today smile.gif

sorry i have to ask so much, trying to get a better understanding of the max llc,
or no vdroop, i just dont get it till now ...lol..i hate that, maybe its just because its monday morning biggrin.gif
Edited by VonDutch - 1/7/13 at 1:53am
BamBam
(17 items)
 
Pebbles
(14 items)
 
 
CPUMotherboardGraphicsRAM
amd 8350 my kids rig :) Gigabyte 990fxa-ud3 Gigabyte 7970 windforce Corsair Vengeance CMZ8GX3M2A1600C9 
Hard DriveHard DriveCoolingOS
500gb OZC vertex 4  Scythe Mugen 3 rev b windows 8.1 
MonitorKeyboardPowerCase
acer 23 inch logitech G510 XFX ProSeries 750W XXX Edition Cooler Master CM 690 II 
MouseAudio
dell  Logitech X-530 
  hide details  
Reply
BamBam
(17 items)
 
Pebbles
(14 items)
 
 
CPUMotherboardGraphicsRAM
amd 8350 my kids rig :) Gigabyte 990fxa-ud3 Gigabyte 7970 windforce Corsair Vengeance CMZ8GX3M2A1600C9 
Hard DriveHard DriveCoolingOS
500gb OZC vertex 4  Scythe Mugen 3 rev b windows 8.1 
MonitorKeyboardPowerCase
acer 23 inch logitech G510 XFX ProSeries 750W XXX Edition Cooler Master CM 690 II 
MouseAudio
dell  Logitech X-530 
  hide details  
Reply
post #7493 of 33576
Quote:
Originally Posted by Valgaur View Post

With the delidding I really thin we should leave a very thin layer of remnant glue on the PCB just as a protective barrier. I did this and had no heat issues at all. especially once I lapped the underside of the IHS including the lips a bit, not much but with 400 grit it goes fast.
So hard to keep up with that thread!
Could you please explain how to lap the underside of the IHS? Any Pics?

Sandpapers should arrive soon, 600 -> 3000 then I'll be ready to go with the delidding process!
Centurion1
(8 items)
 
 
MiniCube
(11 items)
 
CPUMotherboardGraphicsRAM
Intel Pentium4 Northwood MSI 865PE NEO2-S Gainward GeForce 7600 Golden Sample 256 MB AGP8X Corsair TwinX 2x 1GB DDR PC3200 
CoolingOSPowerCase
Thermalright XP-90 + Noiseblocker SE2 92mm Win2000 Tagan TG380 Dual Fan Active PFC CoolerMaster Centurion1 
CPUMotherboardGraphicsRAM
Delidded Ivy Bridge i5 3570K @4.7GHz Asrock Z77E-ITX iGPU HD4000 G.SKILL Ares Series 2x 8GB 1866MHz CL10-11-10-2N 
Hard DriveHard DriveOptical DriveCooling
OCZ Agility 3 120GB Samsung 840 Series 250GB Samsung SE-218BB external DVD/RW Noctua NH-C14 
OSMonitorPowerCase
Windows 7 Ultimate x64 Philips 220CW Silverstone SFX 300W Silverstone Sugo SG05B 
Mouse
Rapoo 7600 
CPUMotherboardGraphicsRAM
Intel i5-5675C 4.4GHz Asus Z97I-Plus ITX Iris Pro Graphics 6200 Crucial Ballistix Sport VLP (2x 8GB) 
Hard DriveHard DriveCoolingOS
Adata Premier Pro SP900 128GB SATA M.2 2280 KingFast 512GB mSATA BeQuiet Dark Rock TF CPU cooler Windows 7 Pro 
MonitorPowerCase
LG 29UM67-P 29" UltraWide 250W FSP FlexATX 80PLUS Bronze Jonsbo case V2 Black 
  hide details  
Reply
Centurion1
(8 items)
 
 
MiniCube
(11 items)
 
CPUMotherboardGraphicsRAM
Intel Pentium4 Northwood MSI 865PE NEO2-S Gainward GeForce 7600 Golden Sample 256 MB AGP8X Corsair TwinX 2x 1GB DDR PC3200 
CoolingOSPowerCase
Thermalright XP-90 + Noiseblocker SE2 92mm Win2000 Tagan TG380 Dual Fan Active PFC CoolerMaster Centurion1 
CPUMotherboardGraphicsRAM
Delidded Ivy Bridge i5 3570K @4.7GHz Asrock Z77E-ITX iGPU HD4000 G.SKILL Ares Series 2x 8GB 1866MHz CL10-11-10-2N 
Hard DriveHard DriveOptical DriveCooling
OCZ Agility 3 120GB Samsung 840 Series 250GB Samsung SE-218BB external DVD/RW Noctua NH-C14 
OSMonitorPowerCase
Windows 7 Ultimate x64 Philips 220CW Silverstone SFX 300W Silverstone Sugo SG05B 
Mouse
Rapoo 7600 
CPUMotherboardGraphicsRAM
Intel i5-5675C 4.4GHz Asus Z97I-Plus ITX Iris Pro Graphics 6200 Crucial Ballistix Sport VLP (2x 8GB) 
Hard DriveHard DriveCoolingOS
Adata Premier Pro SP900 128GB SATA M.2 2280 KingFast 512GB mSATA BeQuiet Dark Rock TF CPU cooler Windows 7 Pro 
MonitorPowerCase
LG 29UM67-P 29" UltraWide 250W FSP FlexATX 80PLUS Bronze Jonsbo case V2 Black 
  hide details  
Reply
post #7494 of 33576
Quote:
Originally Posted by dalastbmills View Post

Hey guys!
Been awhile since I last posted here!
Spent all day yesterday replacing my H80 with a Rasa Extreme RX240 kit! Warning: Spoiler! (Click to show)





I went through some noobie mistakes, like screwing too far and destroying the first radiator! I had to drive 2 hours to Microcenter in Mass to get a replacement!
I ran the loop for a couple hours to test for leaks and would have gone longer but the Houston/Cinncinati football game was boring and I just couldn't wait any longer to see how the results compared!
So, as it currently stand, my idle temps are the same however my load temps seem to have jumped quite a bit. My battlefield 3 gameplay temps have increased 10+ C and my IBT/P95 temps seem to have skyrocketed.
When installing the CPU block I convinced myself that I had too much Liquid Ultra on the die so I removed some. However, I then convinced myself that I removed too much and, being out of Ultra, put on some MX-4. Now, I am worried I put on too much! I have just enough to cover the entire die and have good contact with the IHS and I am all set on the IHS-CPU block contact.
Anyone have any imput? I'm under the impression that MX-4 doesn't need to cure. I'm almost ready to remove the IHS completely or go back to my 2600K and see if I can push 5GHz+.

wait, you changed from H80 to the Rasa Extreme RX240 kit, reassembled it,
and saw the temps go up by 10C compared to the H80 using Ultra?
BamBam
(17 items)
 
Pebbles
(14 items)
 
 
CPUMotherboardGraphicsRAM
amd 8350 my kids rig :) Gigabyte 990fxa-ud3 Gigabyte 7970 windforce Corsair Vengeance CMZ8GX3M2A1600C9 
Hard DriveHard DriveCoolingOS
500gb OZC vertex 4  Scythe Mugen 3 rev b windows 8.1 
MonitorKeyboardPowerCase
acer 23 inch logitech G510 XFX ProSeries 750W XXX Edition Cooler Master CM 690 II 
MouseAudio
dell  Logitech X-530 
  hide details  
Reply
BamBam
(17 items)
 
Pebbles
(14 items)
 
 
CPUMotherboardGraphicsRAM
amd 8350 my kids rig :) Gigabyte 990fxa-ud3 Gigabyte 7970 windforce Corsair Vengeance CMZ8GX3M2A1600C9 
Hard DriveHard DriveCoolingOS
500gb OZC vertex 4  Scythe Mugen 3 rev b windows 8.1 
MonitorKeyboardPowerCase
acer 23 inch logitech G510 XFX ProSeries 750W XXX Edition Cooler Master CM 690 II 
MouseAudio
dell  Logitech X-530 
  hide details  
Reply
post #7495 of 33576
thumb.gif
    
CPUMotherboardGraphicsGraphics
i7 3770k 5.2ghz  GIGABYTE G1 Assassin Sniper 3 7950 with Alphacool block 7950 w/ Alphacool Block 
GraphicsRAMHard DriveCooling
7950 w/ Alphacool block G.SKILL Trident X 2500mhz 2x4gb SanDisk Extreme 240gb sata III 6gbs x5 SwiftTech Apongee Drive II 
CoolingCoolingCoolingOS
Monsta 360 86mm thick rad X 4 MCP 35X Pump x2 400ML Frozen Q Fusion res x3 Windows 7 Ultimate 64 bit 
MonitorKeyboardPowerCase
CatLeap 2560x1440 + Acer hn274h bmiiid 120hz 3D Logitech G19 Corsair Ax1200 watts  Mountain Mods Ascension 
MouseAudio
Logitech M570 Pioneer SP-BS21 Bookshelf Loudspeakers + Lepai Amp 
  hide details  
Reply
    
CPUMotherboardGraphicsGraphics
i7 3770k 5.2ghz  GIGABYTE G1 Assassin Sniper 3 7950 with Alphacool block 7950 w/ Alphacool Block 
GraphicsRAMHard DriveCooling
7950 w/ Alphacool block G.SKILL Trident X 2500mhz 2x4gb SanDisk Extreme 240gb sata III 6gbs x5 SwiftTech Apongee Drive II 
CoolingCoolingCoolingOS
Monsta 360 86mm thick rad X 4 MCP 35X Pump x2 400ML Frozen Q Fusion res x3 Windows 7 Ultimate 64 bit 
MonitorKeyboardPowerCase
CatLeap 2560x1440 + Acer hn274h bmiiid 120hz 3D Logitech G19 Corsair Ax1200 watts  Mountain Mods Ascension 
MouseAudio
Logitech M570 Pioneer SP-BS21 Bookshelf Loudspeakers + Lepai Amp 
  hide details  
Reply
post #7496 of 33576
Quote:
Originally Posted by Hokies83 View Post

thumb.gif

That looks dope Hok! Is this the case you've been talking about getting all along? It looked much bigger in the other pics you've posted.
post #7497 of 33576
Quote:
Originally Posted by PuffinMyLye View Post

That looks dope Hok! Is this the case you've been talking about getting all along? It looked much bigger in the other pics you've posted.

LoL that is just the Psu side of the case and that is a 86mm 480 rad in push/pull and a 64mm rad in push/pull.

Also that is with out the 120mm Top so add another 120mm to it wink.gif

Still waiting on Jim to finish the 120mm roof.
    
CPUMotherboardGraphicsGraphics
i7 3770k 5.2ghz  GIGABYTE G1 Assassin Sniper 3 7950 with Alphacool block 7950 w/ Alphacool Block 
GraphicsRAMHard DriveCooling
7950 w/ Alphacool block G.SKILL Trident X 2500mhz 2x4gb SanDisk Extreme 240gb sata III 6gbs x5 SwiftTech Apongee Drive II 
CoolingCoolingCoolingOS
Monsta 360 86mm thick rad X 4 MCP 35X Pump x2 400ML Frozen Q Fusion res x3 Windows 7 Ultimate 64 bit 
MonitorKeyboardPowerCase
CatLeap 2560x1440 + Acer hn274h bmiiid 120hz 3D Logitech G19 Corsair Ax1200 watts  Mountain Mods Ascension 
MouseAudio
Logitech M570 Pioneer SP-BS21 Bookshelf Loudspeakers + Lepai Amp 
  hide details  
Reply
    
CPUMotherboardGraphicsGraphics
i7 3770k 5.2ghz  GIGABYTE G1 Assassin Sniper 3 7950 with Alphacool block 7950 w/ Alphacool Block 
GraphicsRAMHard DriveCooling
7950 w/ Alphacool block G.SKILL Trident X 2500mhz 2x4gb SanDisk Extreme 240gb sata III 6gbs x5 SwiftTech Apongee Drive II 
CoolingCoolingCoolingOS
Monsta 360 86mm thick rad X 4 MCP 35X Pump x2 400ML Frozen Q Fusion res x3 Windows 7 Ultimate 64 bit 
MonitorKeyboardPowerCase
CatLeap 2560x1440 + Acer hn274h bmiiid 120hz 3D Logitech G19 Corsair Ax1200 watts  Mountain Mods Ascension 
MouseAudio
Logitech M570 Pioneer SP-BS21 Bookshelf Loudspeakers + Lepai Amp 
  hide details  
Reply
post #7498 of 33576
Quote:
Originally Posted by PuffinMyLye View Post

That looks dope Hok! Is this the case you've been talking about getting all along? It looked much bigger in the other pics you've posted.

Which model is that one again?
post #7499 of 33576
Quote:
Originally Posted by PuffinMyLye View Post

Which model is that one again?

That is the TH10

Here is the ST10 see the 120mm roof? that is what im adding to my TH10.

    
CPUMotherboardGraphicsGraphics
i7 3770k 5.2ghz  GIGABYTE G1 Assassin Sniper 3 7950 with Alphacool block 7950 w/ Alphacool Block 
GraphicsRAMHard DriveCooling
7950 w/ Alphacool block G.SKILL Trident X 2500mhz 2x4gb SanDisk Extreme 240gb sata III 6gbs x5 SwiftTech Apongee Drive II 
CoolingCoolingCoolingOS
Monsta 360 86mm thick rad X 4 MCP 35X Pump x2 400ML Frozen Q Fusion res x3 Windows 7 Ultimate 64 bit 
MonitorKeyboardPowerCase
CatLeap 2560x1440 + Acer hn274h bmiiid 120hz 3D Logitech G19 Corsair Ax1200 watts  Mountain Mods Ascension 
MouseAudio
Logitech M570 Pioneer SP-BS21 Bookshelf Loudspeakers + Lepai Amp 
  hide details  
Reply
    
CPUMotherboardGraphicsGraphics
i7 3770k 5.2ghz  GIGABYTE G1 Assassin Sniper 3 7950 with Alphacool block 7950 w/ Alphacool Block 
GraphicsRAMHard DriveCooling
7950 w/ Alphacool block G.SKILL Trident X 2500mhz 2x4gb SanDisk Extreme 240gb sata III 6gbs x5 SwiftTech Apongee Drive II 
CoolingCoolingCoolingOS
Monsta 360 86mm thick rad X 4 MCP 35X Pump x2 400ML Frozen Q Fusion res x3 Windows 7 Ultimate 64 bit 
MonitorKeyboardPowerCase
CatLeap 2560x1440 + Acer hn274h bmiiid 120hz 3D Logitech G19 Corsair Ax1200 watts  Mountain Mods Ascension 
MouseAudio
Logitech M570 Pioneer SP-BS21 Bookshelf Loudspeakers + Lepai Amp 
  hide details  
Reply
post #7500 of 33576
Quote:
Originally Posted by Hokies83 View Post

That is the TH10
Here is the ST10 see the 120mm roof? that is what im adding to my TH10.

I see yes. How much did the case run you? I thought you said something like $800+ but I see it on Case Labs site for $530.

EDIT: Oh you must be referring to the TX10? Damn that thing is a monster biggrin.gif.
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel CPUs
Overclock.net › Forums › Intel › Intel CPUs › [Official] Delidded Club / Guide