Z10PE-D8 WS is ordered, its going to arrive at the end begining of november 2014.
Allready have 1 memory stick 16GB DDR4, 2133 MHz, ECC registered, one more is on the way.
Two E5-2690v3 are allready ordered, i will have them by the end of the month.
Currently owning an EVGA 750ti, with Display port, since i allready own a Asus ROG Swift, allready installed.
I have for more than a week, i havent had the chance to use it yet, because the old PC is sold. Im waiting for the new mainboard and CPUs to arrive.
Im still missing a PSU, and 2 CPU coolers, that i still need to order, to make the PC functional.
The CPU coolers are going to be something generic and cheap, until i can put together the watercooling loops.
Regarding the GPU, im waiting for a bigger maxwell, or even a dual 980 gpu board.
A little bit about the watercooling setup.
A)Loop 1 (CPU0, CPU1, Aquaero 6 XT waterblock, 8xKoolance Ram 33 Ram block)
1)30%of a 140.1 Aquacomputer Aquaplex Radiator (120mm Industrial Noctua Fan 3000 rpm plus Delta 1.2 Amp 190 CFM fan push pull)
2)70% of a 140.2 Aquacomputer Aquaplex Radiator (2x140mm Industrial Noctua Fan 3000 rpm plus 2xDelta 1.2 Amp 190 CFM fan push pull )
3)100% of a 140.2 Aquacomputer Aquaplex Radiator with pump and reservoir included (2x140mm Industrial Noctua Fan 3000 rpm plus 2xDelta 1.2 Amp 190 CFM fan push pull )
4)Waterfilter and flow metter
Total Radiator space 3.7x140x140
2)Loop 2, dual double GPU Cards (the loop can take up to 2 x 500 W cards)
1)70% of a 140.1 Aquacomputer Aquaplex Radiator (Fans are written above)
2)30% of a 140.2 Aquacomputer Aquaplex Radiator (Fans are written above)
3)100% of a 140.3 Aquacomputer Aquaplex Radiator (2x140mm Industrial Noctua Fan 3000 rpm plus 2xDelta 1.2 Amp 190 CFM fan push pull plus 1x140mm Industrial pwm fan with 2000 rpm)
3)100% of a 140.3 Aquacomputer Aquaplex Radiator with reservoir and pump (2x140mm Industrial Noctua Fan 3000 rpm plus 2xDelta 1.2 Amp 190 CFM fan push pull plus 1x140mm Industrial pwm fan with 2000 rpm)
4)Waterfilter and flowmeter
Total radiator space 7.3x140x140, allmost double the first amount.
Delta fans are 120x120x38mm, 12 of them at 1.25 amp will get connector to 6 Poweradjust 3.0, 2 per poweradjust.
The other PWM fans, will get connected to the PWM output of aquaero 6 XT like this
1)CPUwatercoling loop (loop1) plus motherboard tray fans
4x0.55Amp(140mm 3000rpm noctua)+2x0.3Amp(120mm 3000 rpm noctua) = 2.8 Amps for chanell 1
2)GPU watercooling Loop (loop 2)
4x0.55Amp(140mm 3000rpm noctua)+2x0.18(140mm 2000rpm noctua) = 2.56, or only one slow fan for a total of 2.93 Amps for chanell 2
3)4x40mm pwm fans go in the back, 2 deltas with 0.87 Amps each and 2 some other fan with 0.66 amps for a total of 3.06 amps for chanel 3
4)upper case fans and PSU fans, here theres going to be only 2x120 noctua 3000 rpm plus 2x120 NF12P and 2x80mm fan, for a total of 0.86 Amps on chanell 4
Im going to also need 10 or 11 140mm to 120mm fan adapter the best one i could find is the koolance one, made of thcik 5mm aluminum, acts as a small shroud, will allow the mounting of the 120x120x38mm fans on the inner part of the 140mm radiators.
Holy ****, how much is all going to cost. My wife will kill me !
The shopping basket on the aquacomputer website wass alread 1850 Eurs, **** !
the deltas are aprox 500 dollars, the noctus aprox 300 euros, the shop on koolance aprox 400 usd, and i still need to buy 6 memory stick 180 euro each.
PSUs and cpus coolers aprox 500 euros.
Monitor was 800 euros, mainboard 460, and cpus 3800 euros.
She should have allowed me to get the alienware m18 r2 before i decided to build this desktop.
Tommorow i will add photos, for you to see what's the current status.