Overclock.net › Forums › Case Mods & Cases › Builds & Case Mods › Build Logs › TATH \ Caselabs TH 10 + Pedestal "Hill 7.9"
New Posts  All Forums:Forum Nav:

TATH \ Caselabs TH 10 + Pedestal "Hill 7.9" - Page 201

post #2001 of 2245
Thread Starter 
Quote:
Originally Posted by cpachris View Post

I've got lots of the 12/10mm small tubing in the BBBB, and can get 1.25 gpm when the pumps are full speed. That's 4.7 lpm, right? I don't think it's your tubing.

Hi Chris thanks for the information. That is ruled out then.
I have seen that i have one memory waterblock upside down. I can not folow the exact route inside the memory coolblock so i wil change it.
For the rest i have to look what els can be that couses this problem problem.

Like i mention befor it start with 1,9 liter p\m and within seconds the flow almost ends to 0,4 g\pm for two pomp on two radiators.
The flow start at the res, pomp , pomp, radiators, motherboard and then back to the res. between the pomps and the quick disconnect the tubing is hard as if it cant go tru. Mayby the valve of the outgoing from the pedestel closes because the flow pushing upward.

I am glad you mention that thanks
post #2002 of 2245
Thread Starter 
Quote:
Originally Posted by mandrix View Post

You can daisy chain the aquabus to components from both Aquaero's....just need to split everything between them I guess, if that's what you're asking. I don't think there's a need to have a USB connection to all the Aquacomputer stuff if you have them on the aquabus line.

Hi Gerald, what i understand is that when i put the pump on a aquabus connecting i can see it in the Aquasuite program in the Aquaro section. And if i use the usb cable i see it in Aquasuite but not in the Aquero section. I understand now that i have to daisy chain the aquabus cable to the high speed bus of the aquabus connector on the aquero.

I just had info from Chris that it cant be the tubing. That is good news. I mention that i accedently mounted the right memory coolblock upside down. I dont now if that can be the fault.

I have on my pedestel two panel quick disconnects both male. Now i think of it i wonder if the front on pushing the flow tru the pedestel and to the last male quickdisconnect going out it might be that the power of the flo closing the cap "this only can be if there is a defect inside the quick disconnect.
post #2003 of 2245
false
Quote:
Originally Posted by TATH View Post

Hi Gerald, what i understand is that when i put the pump on a aquabus connecting i can see it in the Aquasuite program in the Aquaro section. And if i use the usb cable i see it in Aquasuite but not in the Aquero section. I understand now that i have to daisy chain the aquabus cable to the high speed bus of the aquabus connector on the aquero.

I just had info from Chris that it cant be the tubing. That is good news. I mention that i accedently mounted the right memory coolblock upside down. I dont now if that can be the fault.

I have on my pedestel two panel quick disconnects both male. Now i think of it i wonder if the front on pushing the flow tru the pedestel and to the last male quickdisconnect going out it might be that the power of the flo closing the cap "this only can be if there is a defect inside the quick disconnect.
Yeah like Chris and I both use 12/10 tubing apparently so that can't be it. But I don't know how much the 90's and the QD's affect your flow.

Keep looking....you'll figure it out. Eliminate one thing at at time.
post #2004 of 2245
Thread Starter 
Quote:
Originally Posted by mandrix View Post

false
Yeah like Chris and I both use 12/10 tubing apparently so that can't be it. But I don't know how much the 90's and the QD's affect your flow.

Keep looking....you'll figure it out. Eliminate one thing at at time.

I will, i use 8 90 degree connections in the pedestel.
post #2005 of 2245
Thread Starter 
Yes home again.

Trying to fix the problem. What ever i tried nothing workt the flow went back in seconds to 1 liter a minute.

Now i have more tubing in the house i tryd the other loop. Yes that is better.
Just two problems. Had a small leek at my above my graph card and it ran over my sound card. "hope it is all gone now"mad.gif
Second i dont see cooland in the acrylic blocks. Mayby there is no colland in the acrylic but in the copper section of the cards.

HELP "can some one answer this question.




This is the setup config for the gpu's "No quick disconnects one tube at the back ± 50 cm to the top two 480 radiators.
I had no usb on the pomps but i think the where running at 100%.

You see that al the connections on the pomps are on the front.
On the back i did it different "why i dont now".



Shii.... "my desk is sticky from som cooland. Have to clean this first.

Here you see i use both connections on the front and on the top. Mayby i have to change this.

Chris you where right about the 12mm tubing. 5,5 liter a minute "never dauted you" thumb.gif



Options:
- change the pomp config at the back "and test again:
- not working take appart the outlett of the res to see what is behind those connection.
- not working remove all the hard tubing "in the pedestel and place the Tygon 12" x 3\4".

More solutions "no jokes\ i am the wan ho make jokes oke" are Always welkom.

Ill be back again.
Edited by TATH - 4/8/14 at 11:24am
post #2006 of 2245
If this is the first time you've filled it up...you may just need to wait and bleed out all the air before you'll know what kind of performance you have. It took me FOREVER during my first fill up. Looked like the pumps were hardly moving liquid on up the loop. Sometimes it can help if you have a opening in the loop where air could escape as the initial liquid push occurs. A fill port? Or other opening up high that you could open temporarily while the liquid circulates the first time through the blocks.
post #2007 of 2245
Thread Starter 
Quote:
Originally Posted by cpachris View Post

If this is the first time you've filled it up...you may just need to wait and bleed out all the air before you'll know what kind of performance you have. It took me FOREVER during my first fill up. Looked like the pumps were hardly moving liquid on up the loop. Sometimes it can help if you have a opening in the loop where air could escape as the initial liquid push occurs. A fill port? Or other opening up high that you could open temporarily while the liquid circulates the first time through the blocks.


There is a air release in top of the res.
post #2008 of 2245
Thread Starter 
Cleand up the mes from today.
But i am back tommorow.
I also found the answer about connecting the two cards together. I used 2 bridges but that is wrong you only need one. So that is a extra job.



I had befor these two cards 3 x 580 and between them crystal link tubes on both sides.
post #2009 of 2245
Henry, it is my cosmos II biggrin.gif
post #2010 of 2245
The way you had the cards hooked up is parallel and I may be wrong but don't think it would cause the flow to drop like it has??
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Build Logs
Overclock.net › Forums › Case Mods & Cases › Builds & Case Mods › Build Logs › TATH \ Caselabs TH 10 + Pedestal "Hill 7.9"