Overclock.net › Forums › Case Mods & Cases › Builds & Case Mods › Build Logs › TATH \ Caselabs TH 10 + Pedestal "Hill 7.9"
New Posts  All Forums:Forum Nav:

TATH \ Caselabs TH 10 + Pedestal "Hill 7.9" - Page 42

post #411 of 2245
Thread Starter 
Quote:
Originally Posted by cpachris View Post

1. That is correct. If they are connected by aquabus to the Aquaero, you only need to plug in the USB when you want to update firmware.

2. You should see the PA2's in Aquasuite...but they won't look like the separate tab that they looked like when you plug them in by USB. Instead, you will see additional fans (Fan 5, Fan 6, Fan 7, Fan 8) in the fan screen of the Aquaero. These are your PA2's.

3. No, you don't need any other programs for the PA2's to show...but I would install Aida64 anyway so that you can leverage the temperature data it returns inside some of the aquaero charts and graphs.

Thank you master for showing me the way thumb.gifthumb.gifthumb.gif
post #412 of 2245
Quote:
Originally Posted by TATH View Post

Thank you master for showing me the way thumb.gifthumb.gifthumb.gif

Yes the force is strong in that one!!! biggrin.gif
post #413 of 2245
Thread Starter 
Quote:
Originally Posted by seross69 View Post

Yes the force is strong in that one!!! biggrin.gif

Hi seross,

stil awake, I was on page 45 from the buildlog of seanamus. More tomorrowe "need progress need progress" .
More tomorrowe
thumb.gif
post #414 of 2245
Quote:
Originally Posted by seross69 View Post

Yes the force is strong in that one!!! biggrin.gif

post #415 of 2245
I don't know if you have seen this or not be here is a good how to on the AQ5.

http://www.specialtechforums.co.uk/showthread.php?3393-NAMS-NEW-BASIC-GUIDE-to-the-AQUAERO-5

Also if you look in the page up from this thread he has lots of more information on the AQ5 System and how to set it all up...
post #416 of 2245
Thread Starter 
Quote:
Originally Posted by seross69 View Post

I don't know if you have seen this or not be here is a good how to on the AQ5.

http://www.specialtechforums.co.uk/showthread.php?3393-NAMS-NEW-BASIC-GUIDE-to-the-AQUAERO-5

Also if you look in the page up from this thread he has lots of more information on the AQ5 System and how to set it all up...

Ha love the comment.

Thanks Chris and Scott. Quick cup of coffee and then back to the build.
post #417 of 2245
Thread Starter 
Quote:
Originally Posted by TATH View Post

Ha love the comment.

Thanks Chris and Scott. Quick cup of coffee and then back to the build.

Need more time to spend on the software. After a few pushes in the back i'm back on the track again. I hope my buzzer staying quiet today.
First i wil have a look at the other pages from seanamus i'm at page 46. because i want the switches in like he did i need to now how he made his harness for the aquaro.
If i dont do this first then i must redo my build later. So more time on research and planning.
I have got a mail that the parts (switches and bitspower stuf) shout be sent this weekend. Until now no mail. So i think i got more time for research and expect the package next week.

biggrin.gif:thumb:

New workspace



When the fans are spinning at full speed its like a hover craft. I nowe have the PA2's at 65 and 70%. (about 1000 rpm). On this picture you see 4 wires hanging over the bitpower extender. After the picture was taken i connect the (the original splitter to do som test.



Ahum mayby i can put the black vinyl sticker on the wires from the fans and at the stickers from the fans (al black then)



I wonder if some one uses temp sensor at the PA2's (to measure the temp of the PA2's).



Yes to mutch light get bad picture.


Edited by TATH - 6/9/13 at 1:31am
post #418 of 2245
Quote:
Originally Posted by TATH View Post

Need more time to spend on the software. After a few pushes in the back i'm back on the track again. I hope my buzzer staying quiet today.
First i wil have a look at the other pages from seanamus i'm at page 46. because i want the switches in like he did i need to now how he made his harness for the aquaro.
If i dont do this first then i must redo my build later. So more time on research and planning.
I have got a mail that the parts (switches and bitspower stuf) shout be sent this weekend. Until now no mail. So i think i got more time for research and expect the package next week.

biggrin.gif:thumb:

Good luck with your research and planning thumb.gif just hope you are better at it than me. I always find what i need read all about it and by the time I am ready to use this I have forgot everything I learned. so I might need to do like you and do the learning and research when i need it not months in advance...
post #419 of 2245
Thread Starter 
Quote:
Originally Posted by seross69 View Post

Good luck with your research and planning thumb.gif just hope you are better at it than me. I always find what i need read all about it and by the time I am ready to use this I have forgot everything I learned. so I might need to do like you and do the learning and research when i need it not months in advance...

Your not alone in this. thats why i copy buildlogs and parts of buildlogs. I knowe which parts i need. Bud some times i need more details. And there are always small things to do on the build.

thumb.gif
post #420 of 2245
Quote:
Originally Posted by TATH View Post

Your not alone in this. thats why i copy buildlogs and parts of buildlogs. I knowe which parts i need. Bud some times i need more details. And there are always small things to do on the build.

thumb.gif

Well I do this also TATH I have a 16GB stick half full of all this information but never can seem to find what I want when I need it. Wife tells me getting old and drinking is causing this and tell her it is not drinking enough actually. because drinking kills the weak brain cells and this makes you smarter!!!!
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Build Logs
Overclock.net › Forums › Case Mods & Cases › Builds & Case Mods › Build Logs › TATH \ Caselabs TH 10 + Pedestal "Hill 7.9"