Overclock.net › Forums › Cooling › Water Cooling › Couple different questions (Thermaltake Water 2.0 Extreme)
New Posts  All Forums:Forum Nav:

Couple different questions (Thermaltake Water 2.0 Extreme) - Page 2

post #11 of 20
Thread Starter 
I want to use the on board fan controller in the cooler itself because of the software that comes with it. It actually works well for what I will be doing.

If I wasn't going to use it I have plenty of headers on my mobo
post #12 of 20
after shopping for abit on newegg i didnt see any case that had room for that rad and push pull. until you got to the 130mark
post #13 of 20
Thread Starter 
=(

That was kinda what I was afraid of... I may be able to pull off 150-160 max after shipping but that is about it

I found this one, it is pretty nice, don't know if I can do push/pull but there is a ton of room in it
http://www.newegg.com/Product/Product.aspx?Item=N82E16811119257
Edited by h0thead132 - 12/12/12 at 8:06pm
post #14 of 20
Dosn't look like it. once again a pull only case...

your in luck if you rebate

http://www.newegg.com/Product/Product.aspx?Item=N82E16811119160

The case to get, and has a 30$ rebate atm... so really only spending 110$ before taxes and shipping.
post #15 of 20
Dosn't look like it. once again a pull only case...

your in luck if you rebate

http://www.newegg.com/Product/Product.aspx?Item=N82E16811119160

The case to get, and has a 30$ rebate atm... so really only spending 110$ before taxes and shipping.
post #16 of 20
Thread Starter 
Now could I use the top 230mm fan that already comes with the case as the pull fan? or would that cause issues?
post #17 of 20
It would need to be put ontop of the case, but essential would pull, yet i feel it might block more than pull.

Easy test would be to not have it on, run PC for Abit, moniter temps then just place it on top, or fasten and see if temps drop it stay the same, or even climb...
Edited by Markes12344 - 12/27/12 at 8:01pm
post #18 of 20
Thread Starter 
Well upon looking around and finding tons of reviews and comparisons I think i am going to try and get a case that can do pull. Push gets too much dust and push/pull in most cases only yields a one degree celsius drop.

I am way too indecisive and scatterbrained about this stuff lol

I will most likely grab the 923 advanced because of the massive amount of room and expand-ability it has

Thank you for the help =)
post #19 of 20
Glad i could help, you will be happy with this case for space when it comes to expanding into a bigger water loop. On heads up that i guess i should warn you about... sorry if this changes your mind at all.


But this case failed horribly on making a big CPU back plate hole but not big enough to reveal the hole CPU backplate. as my CPU water block install went i needed to install the back plate then installed the board to the case. soon i will cut out the back plate hole a touch bigg to compensate.

Other than that you will have lots of expansion as stated. even get a great cup/misc item holder on the top of the case, and for the price of the case, especially with that rebate. you wont find a better case for the same price.
post #20 of 20
Thread Starter 
My current case is the same way with the back plate hole, doesn't really bother me much
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Water Cooling
Overclock.net › Forums › Cooling › Water Cooling › Couple different questions (Thermaltake Water 2.0 Extreme)