Overclock.net › Forums › Cooling › Water Cooling › Superglue as sealant?
New Posts  All Forums:Forum Nav:

Superglue as sealant?

post #1 of 13
Thread Starter 
So this one stubborn 45 degree rotary Bitspower fitting has begun to leak a tiny, tiny amount of water since I've replaced my tubing. It's been leak testing now for a couple hours, and about every 15 minutes a small bead of water appears at the same place, on the rotary joint above the threaded knurled portion which screws into the top of the reservoir. I never rotate the joint, so I'm thinking I'm just going to use a small brush to paint the joint shut. Is superglue water soluble? Would it contaminate water in the system? I had a leaky rotary when I first rebuilt it on this water loop a year ago and bought a new one, but I just don't think it's worth the 20 dollars (shipping included) or the time for such a small problem. Any suggestions?

http://www.loctiteproducts.com/p/sg_ug_cntrl/overview/Loctite-Super-Glue-ULTRA-Gel-Control.htm this is the stuff I use to fasten broadheads to my hunting arrow shafts. It's listed as water resistant in the description so I think it may work, since it's an external use situation. Failing that, are there any purpose-made sealants which are able to be applied to tiny areas to stop leaks? Thanks.
Edited by lowfiwhiteguy - 1/19/13 at 7:45pm
Óðinn
(15 items)
 
Methuselah
(15 items)
 
 
CPUMotherboardGraphicsRAM
| Intel Core i7 | 2600K | 4.2GHz @ 1.33v | | ASUS | Maximus IV Extreme | | ASUS | ENGTX 580 | 933MHz @ 1.138v | 2-way SLI | | G.Skill | RipjawsX | 2133MHz | 8GB | 
Hard DriveHard DriveCoolingCooling
| Intel | 510 SSD | 120GB | | Western Digital | Caviar Black | 1TB | | XSPC | Raystorm | | XSPC | Razor 580 | Dual SLI | 
CoolingCoolingCoolingOS
| XSPC | Dual RX360 | | Dual MCP-655 | Variable-Speed | | Koolance | RP-452x2 | Windows 7 Professional 64-bit 
MonitorPowerCase
| Acer | P243W | 1920 x 1200 | | Enermax | MODU87+ | 900W | | CaseLabs | M8 + Pedestal | 
CPUMotherboardGraphicsRAM
| Intel Core i7 | 2600K | 4.2GHz @ 1.33v | | ASUS | Maximus IV Extreme | | ASUS | ENGTX 580 | 933MHz @ 1.138v | 2-way SLI | | G.Skill | RipjawsX | 2133MHz | 8GB | 
Hard DriveHard DriveCoolingCooling
| Intel | 510 SSD | 120GB | | Western Digital | Caviar Black | 1TB | | XSPC | Raystorm | | XSPC | Razer 580 | 2-way SLI | 
CoolingCoolingCoolingOS
| XSPC | RX360 | | Phobya | Xtreme 200| | MCP 655 | Variable-Speed | Windows 7 Professional 64-bit 
MonitorPowerCase
| Acer | P243W | 1920 x 1200 | | Enermax | MODU87+ | 900W | | CoolerMaster | HAF X | 
  hide details  
Reply
Óðinn
(15 items)
 
Methuselah
(15 items)
 
 
CPUMotherboardGraphicsRAM
| Intel Core i7 | 2600K | 4.2GHz @ 1.33v | | ASUS | Maximus IV Extreme | | ASUS | ENGTX 580 | 933MHz @ 1.138v | 2-way SLI | | G.Skill | RipjawsX | 2133MHz | 8GB | 
Hard DriveHard DriveCoolingCooling
| Intel | 510 SSD | 120GB | | Western Digital | Caviar Black | 1TB | | XSPC | Raystorm | | XSPC | Razor 580 | Dual SLI | 
CoolingCoolingCoolingOS
| XSPC | Dual RX360 | | Dual MCP-655 | Variable-Speed | | Koolance | RP-452x2 | Windows 7 Professional 64-bit 
MonitorPowerCase
| Acer | P243W | 1920 x 1200 | | Enermax | MODU87+ | 900W | | CaseLabs | M8 + Pedestal | 
CPUMotherboardGraphicsRAM
| Intel Core i7 | 2600K | 4.2GHz @ 1.33v | | ASUS | Maximus IV Extreme | | ASUS | ENGTX 580 | 933MHz @ 1.138v | 2-way SLI | | G.Skill | RipjawsX | 2133MHz | 8GB | 
Hard DriveHard DriveCoolingCooling
| Intel | 510 SSD | 120GB | | Western Digital | Caviar Black | 1TB | | XSPC | Raystorm | | XSPC | Razer 580 | 2-way SLI | 
CoolingCoolingCoolingOS
| XSPC | RX360 | | Phobya | Xtreme 200| | MCP 655 | Variable-Speed | Windows 7 Professional 64-bit 
MonitorPowerCase
| Acer | P243W | 1920 x 1200 | | Enermax | MODU87+ | 900W | | CoolerMaster | HAF X | 
  hide details  
Reply
post #2 of 13
I say try it, cant hurt to try!
Dark Vader
(6 items)
 
  
CoolingCoolingCoolingCooling
39 X AP-45 2150 rpm Gentle Typhoon fans Lamptron CW611 FrozenQ Dual Bay Reservoir 2x XT45 480. 1x UT60 480 ~ 1x UT60 360 ~ 1x UT... 
OSCase
Linux Ubuntu CaseLabs STH10 
  hide details  
Reply
Dark Vader
(6 items)
 
  
CoolingCoolingCoolingCooling
39 X AP-45 2150 rpm Gentle Typhoon fans Lamptron CW611 FrozenQ Dual Bay Reservoir 2x XT45 480. 1x UT60 480 ~ 1x UT60 360 ~ 1x UT... 
OSCase
Linux Ubuntu CaseLabs STH10 
  hide details  
Reply
post #3 of 13
But leaks do get worst over time. So the super glue should be a quick patch up until you get an other one. And keep an eye on it too.
Dark Vader
(6 items)
 
  
CoolingCoolingCoolingCooling
39 X AP-45 2150 rpm Gentle Typhoon fans Lamptron CW611 FrozenQ Dual Bay Reservoir 2x XT45 480. 1x UT60 480 ~ 1x UT60 360 ~ 1x UT... 
OSCase
Linux Ubuntu CaseLabs STH10 
  hide details  
Reply
Dark Vader
(6 items)
 
  
CoolingCoolingCoolingCooling
39 X AP-45 2150 rpm Gentle Typhoon fans Lamptron CW611 FrozenQ Dual Bay Reservoir 2x XT45 480. 1x UT60 480 ~ 1x UT60 360 ~ 1x UT... 
OSCase
Linux Ubuntu CaseLabs STH10 
  hide details  
Reply
post #4 of 13
Best and safest fix is to just replace the fitting. How old is it? Call up Bitspower and see if they will swap it out. I would maybe get one or two extra, just in case.
post #5 of 13
Why super-glue? It sets rock-hard and has a tendency to dry out rubberized plastics leaving them brittle and porous. It also doesn't work very well unless it's sandwiched very thin between two surfaces. It's not a filler. Use RTV.

http://www.permatex.com/products/product-categories/adhesives-sealants/sealants/permatex--clear-rtv-silicone-adhesive-sealant-detail

*edit* This stuff is on the rack at every home-improvement store and I think even auto-parts shops carry it.
Edited by Cavi Mike - 1/19/13 at 8:04pm
APU what?
(13 items)
 
  
CPUMotherboardRAMHard Drive
AMD A8-3850 Llano(FM1) Gigabyte GA-A75-UD4H 4x G.Skill 4Gb DDR3 3x WD 
Optical DriveOSMonitorKeyboard
LG DVD Seven64 LG 19"LCD / Panny 42"Plasma Logitech Cordless Elite 
PowerCaseMouseMouse Pad
Antec main, Rosewill aux Rosewill Logitech MX700 Couch cushion 
  hide details  
Reply
APU what?
(13 items)
 
  
CPUMotherboardRAMHard Drive
AMD A8-3850 Llano(FM1) Gigabyte GA-A75-UD4H 4x G.Skill 4Gb DDR3 3x WD 
Optical DriveOSMonitorKeyboard
LG DVD Seven64 LG 19"LCD / Panny 42"Plasma Logitech Cordless Elite 
PowerCaseMouseMouse Pad
Antec main, Rosewill aux Rosewill Logitech MX700 Couch cushion 
  hide details  
Reply
post #6 of 13
Quote:
Originally Posted by ericld View Post

Best and safest fix is to just replace the fitting. How old is it? Call up Bitspower and see if they will swap it out. I would maybe get one or two extra, just in case.

Seconded. I had a very good experience with bitspower RMA when I got some damaged fittings on an order. Although be advised they are in Taiwan.
Blinky
(16 items)
 
  
CPUMotherboardGraphicsRAM
i7-950 @4.034 GHz Asus Rampage III Formula GeForce GTX 770 6GB Crucial Ballistix 1600MHz 
Hard DriveCoolingCoolingOS
Samsung 840 Pro SSD EK Supreme HF (full nickel) Danger Den Monsoon Dual-Bay Reservoir/Pump Win 7 Pro 64 
MonitorKeyboardPowerCase
Dell U2410 Rosewill RK-9000 Seasonic X-650 Cosmos 1000 
Other
Lamptron FC5-V2 
  hide details  
Reply
Blinky
(16 items)
 
  
CPUMotherboardGraphicsRAM
i7-950 @4.034 GHz Asus Rampage III Formula GeForce GTX 770 6GB Crucial Ballistix 1600MHz 
Hard DriveCoolingCoolingOS
Samsung 840 Pro SSD EK Supreme HF (full nickel) Danger Den Monsoon Dual-Bay Reservoir/Pump Win 7 Pro 64 
MonitorKeyboardPowerCase
Dell U2410 Rosewill RK-9000 Seasonic X-650 Cosmos 1000 
Other
Lamptron FC5-V2 
  hide details  
Reply
post #7 of 13
I would not use super glue or RTV (RTV is similar to just silicone)

If I was thinking along the lines of patching a hole I would use a 2 part epoxy 3m makes a lot of different kinds. You can get them at hobby stores. They are typically thicker than super glue and you can use this stuff to seal some major gaps if you choose to do so, it just takes a long time to dry.
post #8 of 13
But before you apply the epoxy I would make sure the area is very clean so u get a good bond, that goes with any of the options
post #9 of 13
Yeah, sounds like epoxy is your best bet for a repair. May I reccomned JB WELD. Its under $10 here. Comes in quick and slow dry. (quick dry is about 66% the strength of original) Also it is a non-conductor.

edit: and if you decide to go this route make sure to use some sort of abrasive to "rough up" the surrounding area so you are sure to get good mechanical adhesion. Epoxies tend to not stick well to smooth surfaces.
DEFCON-3
(22 items)
 
   
CPUMotherboardGraphicsRAM
FX-8350 (4.8GHz) Sabertooth 990FX (R1.01/BIOS1604) ASUS GTX 780Ti 2x8GB G.SKILL TRIDENT-X (2140MHz) 
Hard DriveHard DriveHard DriveHard Drive
Samsung 840 PRO 128GB Samsung 850 EVO 500GB Kingston HyperX 3K 128GB Kingston SSDnow 128GB 
Hard DriveOptical DriveOptical DriveCooling
WD Caviar BLACK 500GB ASUS Blu-ray ASUS LightScribe SILVER ARROW SB-E 
OSMonitorKeyboardPower
Windows 7 PRO 64-bit 3x ASUS VN248H (24" 1080p AH-IPS) Logitech G710+ Seasonic G-750 
CaseMouseMouse PadAudio
CM STORM:Trooper (DEFCON-3 MOD) Logitech MX Master Corsair MM600 CREATIVE Sound Blaster Z 
AudioOther
Audio Technica ATH-m50xbl Chill Factor III 
CPUMotherboardGraphicsRAM
AMD Athlon X4 880k ASRock A88M-G/3.1 ASUS GTX 660ti HyperX Fury 8GB 
Hard DriveOptical DriveOSMonitor
Crucial MX300 750GB LG Blu-ray Windows 10 P502ui-b1 
KeyboardPowerCaseAudio
Logitech k400r Rosewill Hive 550W ROSEWILL SRM-01 Vizio S4251W-b4 
CPUMotherboardGraphicsRAM
AMD Phenom II X2 550 MSI 770-C45 Sparkle GT 220 4GB Corsair XMS3 
Hard DriveHard DriveOptical DriveCooling
Western Digital 500GB Caviar Black Seagate Baracuda 1TB ASUS blu-ray Stock 
OSMonitorKeyboardPower
Windows 7 Proffesional  Acer 24"  Logitech Wave OCZ modXtreme Pro 600W 
CaseMouse
Cooler Master Centurion 5 blue Logitech LX8 
  hide details  
Reply
DEFCON-3
(22 items)
 
   
CPUMotherboardGraphicsRAM
FX-8350 (4.8GHz) Sabertooth 990FX (R1.01/BIOS1604) ASUS GTX 780Ti 2x8GB G.SKILL TRIDENT-X (2140MHz) 
Hard DriveHard DriveHard DriveHard Drive
Samsung 840 PRO 128GB Samsung 850 EVO 500GB Kingston HyperX 3K 128GB Kingston SSDnow 128GB 
Hard DriveOptical DriveOptical DriveCooling
WD Caviar BLACK 500GB ASUS Blu-ray ASUS LightScribe SILVER ARROW SB-E 
OSMonitorKeyboardPower
Windows 7 PRO 64-bit 3x ASUS VN248H (24" 1080p AH-IPS) Logitech G710+ Seasonic G-750 
CaseMouseMouse PadAudio
CM STORM:Trooper (DEFCON-3 MOD) Logitech MX Master Corsair MM600 CREATIVE Sound Blaster Z 
AudioOther
Audio Technica ATH-m50xbl Chill Factor III 
CPUMotherboardGraphicsRAM
AMD Athlon X4 880k ASRock A88M-G/3.1 ASUS GTX 660ti HyperX Fury 8GB 
Hard DriveOptical DriveOSMonitor
Crucial MX300 750GB LG Blu-ray Windows 10 P502ui-b1 
KeyboardPowerCaseAudio
Logitech k400r Rosewill Hive 550W ROSEWILL SRM-01 Vizio S4251W-b4 
CPUMotherboardGraphicsRAM
AMD Phenom II X2 550 MSI 770-C45 Sparkle GT 220 4GB Corsair XMS3 
Hard DriveHard DriveOptical DriveCooling
Western Digital 500GB Caviar Black Seagate Baracuda 1TB ASUS blu-ray Stock 
OSMonitorKeyboardPower
Windows 7 Proffesional  Acer 24"  Logitech Wave OCZ modXtreme Pro 600W 
CaseMouse
Cooler Master Centurion 5 blue Logitech LX8 
  hide details  
Reply
post #10 of 13
Thread Starter 
Epoxy it is. I just had to try out this superglue idea, because science, and yeah, didn't work. It just bubbled up white after a second and the water kept coming through. So I wiped it off.

I'm not RMA'ing a 8 dollar part, time is money and I don't have much time. Tomorrow I'll get some of the epoxy mix, I've used it on tonnes of stuff before. I'll slather that on there and see what happens I guess. If that doesn't work I guess it's time for drain/teardown number 3. mad.gif

EDIT: Screw it, I just ordered a replacement fitting. This ghetto epoxy/duct tape hack job will have to hold me over for about a week...

DOUBLE EDIT: Yeah I just decided I'm ordering a CaseLabs M8 with pedestal Monday. I think the reason this fitting started leaking is that working with a tank res, D5, two rads and 3 blocks inside a HAF X is an exercise in frustration due to the cramped quarters, so one ends up knocking stuff accidentally. Nice beginner's case, but it's really on its last legs. I love taking things apart and building them, but for something as lame as a slightly knocked-about rotary fitting (I'm never buying rotaries again, so help me) to just undo 6 hours of work over two days on the thing for nothing is idiocy. Time for a real watercooler's case so I can lay out my loop efficiently and accessibly to avoid this foolishness in future.
Edited by lowfiwhiteguy - 1/19/13 at 9:37pm
Óðinn
(15 items)
 
Methuselah
(15 items)
 
 
CPUMotherboardGraphicsRAM
| Intel Core i7 | 2600K | 4.2GHz @ 1.33v | | ASUS | Maximus IV Extreme | | ASUS | ENGTX 580 | 933MHz @ 1.138v | 2-way SLI | | G.Skill | RipjawsX | 2133MHz | 8GB | 
Hard DriveHard DriveCoolingCooling
| Intel | 510 SSD | 120GB | | Western Digital | Caviar Black | 1TB | | XSPC | Raystorm | | XSPC | Razor 580 | Dual SLI | 
CoolingCoolingCoolingOS
| XSPC | Dual RX360 | | Dual MCP-655 | Variable-Speed | | Koolance | RP-452x2 | Windows 7 Professional 64-bit 
MonitorPowerCase
| Acer | P243W | 1920 x 1200 | | Enermax | MODU87+ | 900W | | CaseLabs | M8 + Pedestal | 
CPUMotherboardGraphicsRAM
| Intel Core i7 | 2600K | 4.2GHz @ 1.33v | | ASUS | Maximus IV Extreme | | ASUS | ENGTX 580 | 933MHz @ 1.138v | 2-way SLI | | G.Skill | RipjawsX | 2133MHz | 8GB | 
Hard DriveHard DriveCoolingCooling
| Intel | 510 SSD | 120GB | | Western Digital | Caviar Black | 1TB | | XSPC | Raystorm | | XSPC | Razer 580 | 2-way SLI | 
CoolingCoolingCoolingOS
| XSPC | RX360 | | Phobya | Xtreme 200| | MCP 655 | Variable-Speed | Windows 7 Professional 64-bit 
MonitorPowerCase
| Acer | P243W | 1920 x 1200 | | Enermax | MODU87+ | 900W | | CoolerMaster | HAF X | 
  hide details  
Reply
Óðinn
(15 items)
 
Methuselah
(15 items)
 
 
CPUMotherboardGraphicsRAM
| Intel Core i7 | 2600K | 4.2GHz @ 1.33v | | ASUS | Maximus IV Extreme | | ASUS | ENGTX 580 | 933MHz @ 1.138v | 2-way SLI | | G.Skill | RipjawsX | 2133MHz | 8GB | 
Hard DriveHard DriveCoolingCooling
| Intel | 510 SSD | 120GB | | Western Digital | Caviar Black | 1TB | | XSPC | Raystorm | | XSPC | Razor 580 | Dual SLI | 
CoolingCoolingCoolingOS
| XSPC | Dual RX360 | | Dual MCP-655 | Variable-Speed | | Koolance | RP-452x2 | Windows 7 Professional 64-bit 
MonitorPowerCase
| Acer | P243W | 1920 x 1200 | | Enermax | MODU87+ | 900W | | CaseLabs | M8 + Pedestal | 
CPUMotherboardGraphicsRAM
| Intel Core i7 | 2600K | 4.2GHz @ 1.33v | | ASUS | Maximus IV Extreme | | ASUS | ENGTX 580 | 933MHz @ 1.138v | 2-way SLI | | G.Skill | RipjawsX | 2133MHz | 8GB | 
Hard DriveHard DriveCoolingCooling
| Intel | 510 SSD | 120GB | | Western Digital | Caviar Black | 1TB | | XSPC | Raystorm | | XSPC | Razer 580 | 2-way SLI | 
CoolingCoolingCoolingOS
| XSPC | RX360 | | Phobya | Xtreme 200| | MCP 655 | Variable-Speed | Windows 7 Professional 64-bit 
MonitorPowerCase
| Acer | P243W | 1920 x 1200 | | Enermax | MODU87+ | 900W | | CoolerMaster | HAF X | 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Water Cooling
Overclock.net › Forums › Cooling › Water Cooling › Superglue as sealant?