Overclock.net › Forums › Intel › Intel CPUs › i7 920 @4.7ghz
New Posts  All Forums:Forum Nav:

i7 920 @4.7ghz

post #1 of 77
Thread Starter 
I am currently stable for hours at 4.64Ghz for Flight Simulator X which this system is dedicated too.
I would like to try to get it to 4.7. The current system setting are below. The CPU Vcore is higher than it needs to be to get 4.64 I just haven’t backed the voltage back to find out the lowest voltage at this clock but under Flight sim load it never gets hotter than 70 degress. I understand the Vcore can go higher it just shows up red in the bios when I notch it up one.

When I notch the BCLK up to 222 and hit f10 it doesn’t even post. I restart and get the system failed because of overclocking or over voltage message.

Anyone got any suggestions as to how I can get to a Setting of 223 or 224 BCLK?

Maybe I should remove one of the 4, 2 gig sticks from the mother board?

>MB Intelligent Tweaker (M.I.T.)
>M.I.T Current Status......................[Press Enter]
>Advanced Frequency Setting...........[Press Enter]
CPU Clock Ratio ................................ [21x]
CPU Frequency 4.64GHz (221x21)
Advanced CPU Core Features...............[Press Enter]
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Disabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Bi-Directional PROCHOT ..................... [Enabled]

QPI Clock Ratio................................[auto]
QPI Link Speed .............................. 7.92 GHz
Unicore Clock Ratio...........................[x16]
Uncore Frequency .......................... 3536MHz

>>>>>Standard Clock Control
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... [221]
Extreme Memory Profile (XPM)...........[Disabled]
System Memory Multiplier (SPD).........[6.0]
Memory Frequency (MHz) 1066..........[1326]
PCI Express Frequency (MHz) ........... [Auto]

>>>>>Advanced Clock Control
CPU Clock Drive ..............................[700mV]
PCI Express Clock Drive ................... [700mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]


>Advanced Memory Settings..........[Press Enter]
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [6.0]
Memory Frequency (MHz) 1066...........1326
Performance Enhance ...................... [Standard]
DRAM Timing Selectable (SPD) .......... [Quick]
Profile DDR Voltage............................1.5v
Profile QPI Voltage.............................1.175v
Channel Interleaving 6....................[Auto]
Rank Interleaving 4....................[Auto]

>>>>>>Channel A
Channel A Timing Settings..................[Press Enter]
>>>>> Channel A Standard Timing Control
CAS Latency Time 8..........[ 7]
tRCD 8..........[ 7]
tRP 8..........[ 7]
tRAS 20........[ 24]
>>>>> Channel A Advanced Timing Control
tRC 27........[Auto]
tRRD 4..........[Auto]
tWTR 4..........[Auto]
tWR 8..........[Auto]
tWTP 19........[Auto]
tWL 7..........[Auto]
tRFC 60........[Auto]
tRTP 4..........[Auto]
tFAW 20........[Auto]
Command Rate (CMD) 2..........[Auto]
>>>>> Channel A Misc Timing Control
B2B CAS Delay -..........[Auto]
Round Trip Latency 61........[Auto]


>Advanced Voltage Settings
******Mother Board Voltage Control******
Voltage Type Normal Current
>>> CPU
Load-Line Calibration [Standard]
CPU Vcore 1.22500V [1.54375V]
x Dynamic Vcore (DVID) +0.00000V Auto
QPI/Vtt Voltage 1.175V [1.335V]
CPU PLL 1.800V [1.500V]
>>> MCH/ICH
PCIE 1.500v [Auto]
QPI PLL 1.100v [1.400V]
IOH Core 1.100v [Auto]
ICH I/O 1.500v [Auto]
ICH Core 1.100v [Auto]
>>> DRAM
DRAM Voltage 1.500v [1.620V]
DRAM Termination 0.750v [Auto]
Ch-A Data VRef. 0.750v [Auto]
Ch-B Data VRef. 0.750v [Auto]
Ch-C Data VRef. 0.750v [Auto]
Ch-A Address VRef. 0.750v [Auto]
Ch-B Address VRef. 0.750v [Auto]
Ch-C Address VRef. 0.750v [Auto]
post #2 of 77
Raise pcie frequency. I wouldn't go past 110.
http://www.overclock.net/t/1207764/max-safe-pci-e-frequency/0_100

Nice overclock BTW!
post #3 of 77
did you try it?
post #4 of 77
Thread Starter 
Yes I did. I can boot at up to 4.72ghz. When I start 3DMark06 I just about get to the end of the first test before BSOD and with flight Sim X It BSOD just after the flight loads. Stop: 0x124 in bought cases. If I have a little time I will latter I will play with the voltages a little at 4.7 and so if I can't get right through 3DMark06 for a start. I will post the bios setting latter on to see if I can get some suggested values for voltages and or memory setting. Pci-e is at 102Mhz righ tnow.
Thanks for the nelp:)
post #5 of 77
Thread Starter 
OK, Got to 4.7 Getting BSOD Stop 0x124.

BSOD occurs just after FSX flight loads or somewhere durring the first 3DMark06 SM2 graphics test.

I could just stick to 4.64ghz where I have run FSX for a couple of hours but where is the fun in that:-)

Bios setting are below. Anyone like to make any recommendations.


>MB Intelligent Tweaker (M.I.T.)
>M.I.T Current Status......................[Press Enter]
>Advanced Frequency Setting...........[Press Enter]
CPU Clock Ratio ................................ [21x]
CPU Frequency 4.7GHz (224x21)
Advanced CPU Core Features...............[Press Enter]
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Disabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Bi-Directional PROCHOT ..................... [Enabled]

QPI Clock Ratio................................[auto]
QPI Link Speed .............................. 8.06GHz
Unicore Clock Ratio...........................[x16]
Uncore Frequency .......................... 3584MHz

>>>>>Standard Clock Control
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... [224]
Extreme Memory Profile (XPM)...........[Disabled]
System Memory Multiplier (SPD).........[8.0]
Memory Frequency (MHz) 1066..........[1792]
PCI Express Frequency (MHz) ........... [102]

>>>>>Advanced Clock Control
CPU Clock Drive ..............................[700mV]
PCI Express Clock Drive ................... [700mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]


>Advanced Memory Settings..........[Press Enter]
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [6.0]
Memory Frequency (MHz) 1066...........1320
Performance Enhance ...................... [Standard]
DRAM Timing Selectable (SPD) .......... [Quick]
Profile DDR Voltage............................1.5v
Profile QPI Voltage.............................1.175v
Channel Interleaving 6....................[Auto]
Rank Interleaving 4....................[Auto]

>>>>>>Channel A
Channel A Timing Settings..................[Press Enter]
>>>>> Channel A Standard Timing Control
CAS Latency Time 8..........[ 9]
tRCD 8..........[ 9]
tRP 8..........[ 9]
tRAS 20........[ 27]
>>>>> Channel A Advanced Timing Control
tRC 27........[Auto]
tRRD 4..........[Auto]
tWTR 4..........[Auto]
tWR 8..........[Auto]
tWTP 19........[Auto]
tWL 7..........[Auto]
tRFC 60........[Auto]
tRTP 4..........[Auto]
tFAW 20........[Auto]
Command Rate (CMD) 1..........[2]
>>>>> Channel A Misc Timing Control
B2B CAS Delay -..........[Auto]
Round Trip Latency 59........[Auto]

Channel A Turnaround Settings...........[Press Enter]
>>>>>Channel A Reads Followed by Reads
Different DIMMs 6.........[Auto]
Different Ranks 5.........[Auto]
On The Same Rank 1.........[Auto]
>>>>> Channel A Writes Followed by Writes
Different Dimms 6........[Auto]
Different Ranks 6.........[Auto]
On The Same Rank 1.........[Auto]

>Advanced Voltage Settings
******Mother Board Voltage Control******
Voltage Type Normal Current
>>> CPU
Load-Line Calibration [Standard]
CPU Vcore 1.22500V [1.56250V]
x Dynamic Vcore (DVID) +0.00000V Auto
QPI/Vtt Voltage 1.175V [1.395V]
CPU PLL 1.800V [1.500V]
>>> MCH/ICH
PCIE 1.500v [Auto]
QPI PLL 1.100v [1.440V]
IOH Core 1.100v [Auto]
ICH I/O 1.500v [Auto]
ICH Core 1.100v [Auto]
>>> DRAM
DRAM Voltage 1.500v [1.660V]
DRAM Termination 0.750v [Auto]
Ch-A Data VRef. 0.750v [Auto]
Ch-B Data VRef. 0.750v [Auto]
Ch-C Data VRef. 0.750v [Auto]
Ch-A Address VRef. 0.750v [Auto]
Ch-B Address VRef. 0.750v [Auto]
Ch-C Address VRef. 0.750v [Auto]

> Miscellaneous Settings
Isochronous Support [Enabled]
Virtualisation Technology [Enabled]
post #6 of 77
Try playing with QPI/VTT and if that does not work try vcore if you dare!!! I hope this helps
Quote:
Originally Posted by HaMMeR=GoM= View Post

BSOD codes for overclocking
BSOD Codes for i7 x58 chipset
0x101 = increase vcore
0x124 = increase/decrease QPI/VTT first, if not increase/decrease vcore...have to test to see which one it is
0x0A = unstable RAM/IMC, increase QPI first, if that doesn't work increase vcore
0x1A = Memory management error. It usually means a bad stick of Ram. Test with Memtest or whatever you prefer. Try raising your Ram voltage
0x1E = increase vcore
0x3B = increase vcore
0x3D = increase vcore
0xD1 = QPI/VTT, increase/decrease as necessary, can also be unstable Ram, raise Ram voltage
0x9C = QPI/VTT most likely, but increasing vcore has helped in some instances
0x50 = RAM timings/Frequency or uncore multi unstable, increase RAM voltage or adjust QPI/VTT, or lower uncore if you're higher than 2x
0x109 = Not enough or too Much memory voltage
0x116 = Low IOH (NB) voltage, GPU issue (most common when running multi-GPU/overclocking GPU)
0x7E = Corrupted OS file, possibly from overclocking. Run sfc /scannow and chkdsk /r
/eVo/HaMMeR=GoM=
post #7 of 77
Thread Starter 
Thanks, I found that already.
I don't think I 4.7 is possible.
But I making progress at 4.68
I get through 3DMark06 and scrore
arround 30,800 each time.
I just need to see howe long it runs
FSX reliably.
This I am accepting is the limit.
post #8 of 77
Thats a hell of an overclock for bloomfield
Core I7 5960X
(10 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Core I7 5960X ASRock X99 OC Formula MSI GTX 970 Gaming MSI GTX 970 Gaming 
RAMHard DriveCoolingOS
G. Skill 16GB DDR4 2600 Sandisk Extreme II 240GB SSD Custom 480 Water Setup Windows 10 
PowerCase
AX1500I Corsair 900D 
  hide details  
Reply
Core I7 5960X
(10 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Core I7 5960X ASRock X99 OC Formula MSI GTX 970 Gaming MSI GTX 970 Gaming 
RAMHard DriveCoolingOS
G. Skill 16GB DDR4 2600 Sandisk Extreme II 240GB SSD Custom 480 Water Setup Windows 10 
PowerCase
AX1500I Corsair 900D 
  hide details  
Reply
post #9 of 77
Quote:
Originally Posted by Stay Puft View Post

Thats a hell of an overclock for bloomfield

Aye I was just thinking that. That thing's gotta be dumping heat like a mother.
Heisenberg
(10 items)
 
Redemption
(18 items)
 
 
CPUGraphicsRAMHard Drive
Intel Core 2 Extreme @ 2.8GHz (upgrade) Intel GMA 950 2 x 2 DDR2 667MHz (upgrade) 120GB Mushkin ECO2 
Optical DriveOSMonitorPower
Replaced with 42 W/hr aux battery Mint 17.3 1280x800 Dell 65w Dell Adapter 
CaseOther
Latitude D630 Chassis Intel 7260-802.11ac 2x2 
CPUMotherboardGraphicsRAM
Not telling AsRock something Pixel Pusher 2 x 8 GB AMD Radeon RAM @ 1600mhz (All the VM's) 
Hard DriveHard DriveHard DriveOptical Drive
Crucial M4 128GB (8 second boot) Western Digital RE4 1TB Western Digital RE4 2TB Pioneer Blu-Ray Reader/Writer 
CoolingOSMonitorKeyboard
Cooler Master Hyper 212 Evo Windows 8.1 Pro x64 Dell U2713HM IBM Model M (CLICKY!!) 
PowerCaseMouseAudio
Antec HCG-900 NZXT Source 210 (it was cheap) Logitech G502 Schiit Modi 
AudioAudio
Sennheiser HD 598 M-Audio AV40's 
CPUMotherboardGraphicsRAM
Intel Core i5-4200U Microsoft BGA1168 Intel HD 4400 8 GB LPDDR3 Dual Channel @ 1600mhz 
Hard DriveOSMonitorKeyboard
SK Hynix 256GB SSD Windows 8.1 Professional 1920 x 1080p IPS Display Microsoft Touch Cover 2 
Power
48w PSU 
  hide details  
Reply
Heisenberg
(10 items)
 
Redemption
(18 items)
 
 
CPUGraphicsRAMHard Drive
Intel Core 2 Extreme @ 2.8GHz (upgrade) Intel GMA 950 2 x 2 DDR2 667MHz (upgrade) 120GB Mushkin ECO2 
Optical DriveOSMonitorPower
Replaced with 42 W/hr aux battery Mint 17.3 1280x800 Dell 65w Dell Adapter 
CaseOther
Latitude D630 Chassis Intel 7260-802.11ac 2x2 
CPUMotherboardGraphicsRAM
Not telling AsRock something Pixel Pusher 2 x 8 GB AMD Radeon RAM @ 1600mhz (All the VM's) 
Hard DriveHard DriveHard DriveOptical Drive
Crucial M4 128GB (8 second boot) Western Digital RE4 1TB Western Digital RE4 2TB Pioneer Blu-Ray Reader/Writer 
CoolingOSMonitorKeyboard
Cooler Master Hyper 212 Evo Windows 8.1 Pro x64 Dell U2713HM IBM Model M (CLICKY!!) 
PowerCaseMouseAudio
Antec HCG-900 NZXT Source 210 (it was cheap) Logitech G502 Schiit Modi 
AudioAudio
Sennheiser HD 598 M-Audio AV40's 
CPUMotherboardGraphicsRAM
Intel Core i5-4200U Microsoft BGA1168 Intel HD 4400 8 GB LPDDR3 Dual Channel @ 1600mhz 
Hard DriveOSMonitorKeyboard
SK Hynix 256GB SSD Windows 8.1 Professional 1920 x 1080p IPS Display Microsoft Touch Cover 2 
Power
48w PSU 
  hide details  
Reply
post #10 of 77
Quote:
Originally Posted by coachmark2 View Post

Aye I was just thinking that. That thing's gotta be dumping heat like a mother.

I wish we had the coolers of today back in 2008 when Bloomfield came out. I would have loved a 4.5ghz 920
Core I7 5960X
(10 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Core I7 5960X ASRock X99 OC Formula MSI GTX 970 Gaming MSI GTX 970 Gaming 
RAMHard DriveCoolingOS
G. Skill 16GB DDR4 2600 Sandisk Extreme II 240GB SSD Custom 480 Water Setup Windows 10 
PowerCase
AX1500I Corsair 900D 
  hide details  
Reply
Core I7 5960X
(10 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Core I7 5960X ASRock X99 OC Formula MSI GTX 970 Gaming MSI GTX 970 Gaming 
RAMHard DriveCoolingOS
G. Skill 16GB DDR4 2600 Sandisk Extreme II 240GB SSD Custom 480 Water Setup Windows 10 
PowerCase
AX1500I Corsair 900D 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel CPUs
Overclock.net › Forums › Intel › Intel CPUs › i7 920 @4.7ghz