Overclock.net › Forums › Cooling › Water Cooling › flow rate
New Posts  All Forums:Forum Nav:

flow rate

post #1 of 4
Thread Starter 
anyone know the flow rate on the h220 at 100% in gpm
post #2 of 4
This is the only information I have found on the internet

440 l/h = 1,94 US GPM = 1,61 Imp GPM

But if you refer to this thread, they say around 1 GPM

http://forums.swiftech.org/viewtopic.php?f=20&t=2007

Quad Damage
(24 items)
 
  
CPUMotherboardGraphicsRAM
Intel i7 4930k @ 4.6Ghz Asus Rampage IV Extreme (Koolance Full WB) 2 x GTX 1080ti FE in SLI (EK WATERBLOCK) Corsair Dominator GT 2133 MHz (16GB) 
Hard DriveHard DriveHard DriveHard Drive
3 TB Seagate OCZ Vertex 4 256GB Crucial M4 128GB ADATA SX900 128GB 
CoolingCoolingCoolingCooling
RIVE Koolance Waterblock (VRM and PCH) Feser X-Changer 360 Feser X-Changer 240 Feser X-Changer 480 
CoolingCoolingCoolingOS
WaterCool MoRA3 Pro with Gentle Typhoon 3 x MCP 655 pumps (With EK top...all serial) 2 x EK FC 1080ti Blocks Windows 7 Ultimate x64 
MonitorMonitorKeyboardPower
Asus ROG Swift PG348Q (3440x1440 @100hz) CrossOver 27Q Led-P Logitech G15 EVGA SuperNova 1600T2 (Titanium) 
CaseMouseMouse PadAudio
Corsair Obsidian Heavily Modded Logitech G700 RocketFish Speed/Control M-audio AV-40 (Logitech G-35) 
  hide details  
Reply
Quad Damage
(24 items)
 
  
CPUMotherboardGraphicsRAM
Intel i7 4930k @ 4.6Ghz Asus Rampage IV Extreme (Koolance Full WB) 2 x GTX 1080ti FE in SLI (EK WATERBLOCK) Corsair Dominator GT 2133 MHz (16GB) 
Hard DriveHard DriveHard DriveHard Drive
3 TB Seagate OCZ Vertex 4 256GB Crucial M4 128GB ADATA SX900 128GB 
CoolingCoolingCoolingCooling
RIVE Koolance Waterblock (VRM and PCH) Feser X-Changer 360 Feser X-Changer 240 Feser X-Changer 480 
CoolingCoolingCoolingOS
WaterCool MoRA3 Pro with Gentle Typhoon 3 x MCP 655 pumps (With EK top...all serial) 2 x EK FC 1080ti Blocks Windows 7 Ultimate x64 
MonitorMonitorKeyboardPower
Asus ROG Swift PG348Q (3440x1440 @100hz) CrossOver 27Q Led-P Logitech G15 EVGA SuperNova 1600T2 (Titanium) 
CaseMouseMouse PadAudio
Corsair Obsidian Heavily Modded Logitech G700 RocketFish Speed/Control M-audio AV-40 (Logitech G-35) 
  hide details  
Reply
post #3 of 4
Yes, about 0.6 GPM with the h220 rad.
swiftech-h220-pq01b.png

Plenty for good thermal performance but it can require some extra effort to bleed properly. For reference I have measured air pockets sticking in 1/2 tubing in about .3GPM flow rates so you'll want to plan on bleeding outside the system where you can freely toss and turn the various bits around to encourage the more stubborn bubbles a bit more. May also want to run series rather than parallel on GPU sli since that cuts flow in balf across the GPUs.
Edited by Martinm210 - 5/21/13 at 6:18pm
    
CPUMotherboardGraphicsRAM
3930K ASrock X79 Ext7 Evga GTX570 CORSAIR Vengeance 16GB 
Hard DriveOptical DriveOSMonitor
Phoenix SSD+2TB Seagate drives ASUS DVD-RW combo Windows 7 28" Hanns-G HZ281 
KeyboardPowerCaseMouse
MS Natural Corsair TX650 Danger Den Torture Rack Logitech MX518 
Mouse Pad
Desk 
  hide details  
Reply
    
CPUMotherboardGraphicsRAM
3930K ASrock X79 Ext7 Evga GTX570 CORSAIR Vengeance 16GB 
Hard DriveOptical DriveOSMonitor
Phoenix SSD+2TB Seagate drives ASUS DVD-RW combo Windows 7 28" Hanns-G HZ281 
KeyboardPowerCaseMouse
MS Natural Corsair TX650 Danger Den Torture Rack Logitech MX518 
Mouse Pad
Desk 
  hide details  
Reply
post #4 of 4
Thread Starter 
thank you
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Water Cooling
Overclock.net › Forums › Cooling › Water Cooling › flow rate