Overclock.net › Forums › Case Mods & Cases › Computer Cases › [Official] Corsair Carbide Air 540 Owner's Club +Gallery
New Posts  All Forums:Forum Nav:

[Official] Corsair Carbide Air 540 Owner's Club +Gallery - Page 1237

post #12361 of 12386
Just put a ML140 Pro in as the exhaust. You can leave the corners on with a little help getting the fan in place.

Connect the fan with the 2 inner screws quite tightly. Use a small screwdriver to lever the other side of the fan in place. Put the screwdriver in-between the case and the fan and slowly push toward the middle of the case. The outer edge of the case will bend a little. When the fan goes in the case will push back flush again. The case won't look out of shape as the windowed side still fits flush.

Nice fans but how Corsair manage to make a fan that can't fit properly into a case they made is very poor to say the least.
Edited by 1stMonkey - 3/23/17 at 11:31pm
post #12362 of 12386
Could either of you that have had issues fitting the ML140 in the rear measure the width & hole spacing of the ML 140? I'm just curious to know how much it differs from other 140mm fans.
Here are some measurements I took for comparison:
Fan Width (+/-0.1mm) Hole Spacing (+/-1mm)
Corsair A1425L12S-2 139.6mm 125mm
Phanteks PH-F140SP 139.7mm 124mm

With a PH-F140SP installed, I have about 2.5mm clearance from the edge of the fan to the inside edge of the case. @dboythagr8 I saw the picture you posted, but I can't tell what's keeping you from lining up the holes. Is because the notch in the flange on the case isn't wide enough? Does the corner of the fan hit it, or is something else going on?

I did measure the flange cutout on my case. It appears to be 136.5mm with a 45° slope Towards the inside of the case. The flange extends 6mm into the case where not cut out. This could prevent a perfectly square fan with sharp corners over 140mm from fitting, but most of the fans I've seen have beveled, chamfered, or inset corners, so I wouldn't expect that flange to realistically matter. I'm just curious as to whether the issue is the fan or fab issues with the case.

Here's a few pictures with my PH-F140SP installed:

Gigabyte Z170
(23 items)
 
 
Brother's Machine
(15 items)
 
CPUMotherboardGraphicsRAM
i5-6600k GIGABYTE G1.Sniper Z170 EVGA GeForce GTX 1070 FTW Corsair Vengeance LPX 16GB (2 x 8GB) DDR4-3000 
Hard DriveHard DriveOptical DriveCooling
Samsung 950 Pro 512GB M.2280 Seagate Barracuda 2TB 3.5" 7200RPM LG WH14NS40 Blu-Ray/DVD/CD Writer Phanteks PH-TC14PE_BL 
CoolingCoolingCoolingCooling
Phanteks PH-F140SP Phanteks PH-F140SP Phanteks PH-F140SP Phanteks PH-F140SP 
CoolingCoolingOSMonitor
Phanteks PH-F140SP Phanteks PH-F120SP Windows 10 Pro Visio E601i-A3 
KeyboardPowerCaseMouse
Logitech K400 EVGA SuperNOVA 750 G2 Phanteks Enthoo Luxe Logitech G600 MMO 
OtherOtherOther
XBox One Controller Reeven Four Eyes Touch HTC Vive 
CPUMotherboardRAMHard Drive
Pentium G4560 ASUS H110M-A/M.2 Corsair Vengeance LPX Western Digital Caviar Blue 
Hard DriveCoolingOSPower
Western Digital Caviar Blue Cryorig H7 Undecided EVGA Supernova G2 750W 
CaseOther
Corsair Air 540 Phanteks PH-F140SP 
CPUMotherboardGraphicsRAM
i3-2120 ACER IPISB-VR EVGA GTX 260 3x2GB DDR3 
Hard DriveOptical DriveOptical DriveCooling
Wester Digital Green ASUS DVD RW DVD RW Stock Cooler 
CoolingCoolingCoolingOS
Noctua NF-S12B Redux-1200 Noctua NF-S12B Redux-1200 Noctua NF-S12B Redux-1200 Windows 10 Pro 
PowerCaseMouse
Thermaltake TR2 500W Corsair Carbide Spec-01 Microsoft Intellimouse 
  hide details  
Reply
Gigabyte Z170
(23 items)
 
 
Brother's Machine
(15 items)
 
CPUMotherboardGraphicsRAM
i5-6600k GIGABYTE G1.Sniper Z170 EVGA GeForce GTX 1070 FTW Corsair Vengeance LPX 16GB (2 x 8GB) DDR4-3000 
Hard DriveHard DriveOptical DriveCooling
Samsung 950 Pro 512GB M.2280 Seagate Barracuda 2TB 3.5" 7200RPM LG WH14NS40 Blu-Ray/DVD/CD Writer Phanteks PH-TC14PE_BL 
CoolingCoolingCoolingCooling
Phanteks PH-F140SP Phanteks PH-F140SP Phanteks PH-F140SP Phanteks PH-F140SP 
CoolingCoolingOSMonitor
Phanteks PH-F140SP Phanteks PH-F120SP Windows 10 Pro Visio E601i-A3 
KeyboardPowerCaseMouse
Logitech K400 EVGA SuperNOVA 750 G2 Phanteks Enthoo Luxe Logitech G600 MMO 
OtherOtherOther
XBox One Controller Reeven Four Eyes Touch HTC Vive 
CPUMotherboardRAMHard Drive
Pentium G4560 ASUS H110M-A/M.2 Corsair Vengeance LPX Western Digital Caviar Blue 
Hard DriveCoolingOSPower
Western Digital Caviar Blue Cryorig H7 Undecided EVGA Supernova G2 750W 
CaseOther
Corsair Air 540 Phanteks PH-F140SP 
CPUMotherboardGraphicsRAM
i3-2120 ACER IPISB-VR EVGA GTX 260 3x2GB DDR3 
Hard DriveOptical DriveOptical DriveCooling
Wester Digital Green ASUS DVD RW DVD RW Stock Cooler 
CoolingCoolingCoolingOS
Noctua NF-S12B Redux-1200 Noctua NF-S12B Redux-1200 Noctua NF-S12B Redux-1200 Windows 10 Pro 
PowerCaseMouse
Thermaltake TR2 500W Corsair Carbide Spec-01 Microsoft Intellimouse 
  hide details  
Reply
post #12363 of 12386
Quote:
Originally Posted by 1stMonkey View Post

Just put a ML140 Pro in as the exhaust. You can leave the corners on with a little help getting the fan in place.

Connect the fan with the 2 inner screws quite tightly. Use a small screwdriver to lever the other side of the fan in place. Put the screwdriver in-between the case and the fan and slowly push toward the middle of the case. The outer edge of the case will bend a little. When the fan goes in the case will push back flush again. The case won't look out of shape as the windowed side still fits flush.

Nice fans but how Corsair manage to make a fan that can't fit properly into a case they made is very poor to say the least.

I just wanted to save a few bucks if the 120 on the back was enough, thanks for the tips though.
post #12364 of 12386
I've clean my PC today and took some pics!




My gaming rig
(12 items)
 
  
CPUMotherboardGraphicsRAM
i7 4790k Asus Maximus Hero VII EVGA GTX 1070 FTW Corsair Vengeance Pro 2x8GB 2400Mhz CL11 
Hard DriveHard DriveMonitorKeyboard
WD 1TB 7200RPM Samsung 850 PRO 512GB Asus VG248QE Corsair Strafe 
PowerCaseMouseMouse Pad
Corsair AX860 Corsair Air 540 Steelseries Rival 100 Razer Goliathus Control V2 
  hide details  
Reply
My gaming rig
(12 items)
 
  
CPUMotherboardGraphicsRAM
i7 4790k Asus Maximus Hero VII EVGA GTX 1070 FTW Corsair Vengeance Pro 2x8GB 2400Mhz CL11 
Hard DriveHard DriveMonitorKeyboard
WD 1TB 7200RPM Samsung 850 PRO 512GB Asus VG248QE Corsair Strafe 
PowerCaseMouseMouse Pad
Corsair AX860 Corsair Air 540 Steelseries Rival 100 Razer Goliathus Control V2 
  hide details  
Reply
post #12365 of 12386
Quote:
Originally Posted by dboythagr8 View Post

Managed to take some pictures showing the difference between the stock 540 140mm fan that fits in the rear no problem vs the ML Pros
Warning: Spoiler! (Click to show)




Up against the case as far as it can go


After messing with this for some time this morning trying to force it every which way, I finally just removed 2 of the corners from the ML Pro, and was was able to get two screws on the remaining corners opposite of each other. That worked and it's now in the case.

If you're having the same problem I did with mounting a fan in the rear exhaust position, the issues aren't related to the location of the holes. They should all line up perfectly. Try attaching the fan from the outside of the case just to verify this.

If it mounts fine on the outside of the case, then you should check out the metal lip that protrudes into the area above the fan mounts. The rubber corners of the Corsair fans impacts with this metal lip and prevents proper mounting of the fan. I had to notch the rubber in my AF140 before it would fit properly because of this. Check the image in my spoiler tag here to see how I notched my fan to get it to fit.
Warning: Spoiler! (Click to show)
     
CPUMotherboardGraphicsRAM
Intel Core i5-6600K 6M Skylake Quad-Core 3.5 GH... ASUS Z170-PRO LGA 1151 Intel Z170 HDMI SATA 6Gb... ASUS ROG GeForce GTX 1070 STRIX-GTX1070-O8G-GAM... G.SKILL Ripjaws V Series 32GB (4 x 8GB) 288-Pin... 
Hard DriveHard DriveCoolingOS
SAMSUNG 850 PRO 2.5" 256GB SATA III 3-D Vertica... WD Black 1TB Performance Desktop Hard Disk Driv... Corsair Hydro Series H100i V2 Extreme Performan... Windows 10 Pro 64-bit 
MonitorKeyboardPowerCase
ASUS ROG PG278Q Black 27" WQHD 2560 x 1440, 144... Corsair K70 EVGA SuperNOVA 850 G2 Thermaltake Core X5 
Mouse
Logitech Proteus Core G502 
  hide details  
Reply
     
CPUMotherboardGraphicsRAM
Intel Core i5-6600K 6M Skylake Quad-Core 3.5 GH... ASUS Z170-PRO LGA 1151 Intel Z170 HDMI SATA 6Gb... ASUS ROG GeForce GTX 1070 STRIX-GTX1070-O8G-GAM... G.SKILL Ripjaws V Series 32GB (4 x 8GB) 288-Pin... 
Hard DriveHard DriveCoolingOS
SAMSUNG 850 PRO 2.5" 256GB SATA III 3-D Vertica... WD Black 1TB Performance Desktop Hard Disk Driv... Corsair Hydro Series H100i V2 Extreme Performan... Windows 10 Pro 64-bit 
MonitorKeyboardPowerCase
ASUS ROG PG278Q Black 27" WQHD 2560 x 1440, 144... Corsair K70 EVGA SuperNOVA 850 G2 Thermaltake Core X5 
Mouse
Logitech Proteus Core G502 
  hide details  
Reply
post #12366 of 12386
Quote:
Originally Posted by ViTosS View Post

I've clean my PC today and took some pics!

Pretty sweet rig, I really like the color combo and coordination. Looks sharp!
post #12367 of 12386
Quote:
Originally Posted by NaciremaDiputs View Post

If you're having the same problem I did with mounting a fan in the rear exhaust position, the issues aren't related to the location of the holes. They should all line up perfectly. Try attaching the fan from the outside of the case just to verify this.

If it mounts fine on the outside of the case, then you should check out the metal lip that protrudes into the area above the fan mounts. The rubber corners of the Corsair fans impacts with this metal lip and prevents proper mounting of the fan. I had to notch the rubber in my AF140 before it would fit properly because of this. Check the image in my spoiler tag here to see how I notched my fan to get it to fit.
Warning: Spoiler! (Click to show)
It looks like the lip on your case doesn't have nearly as large a cutout as mine does. Does it only taper in about 1/2" inside of the bolt holes? I'm starting to wonder if there was a revision to the case that changed that. The cutout on mine was wide enough that I'm certain that a full 140x140 framed fan would fit without issue, but it looks like you'd struggle to get more than a round framed fan in the same location.
Gigabyte Z170
(23 items)
 
 
Brother's Machine
(15 items)
 
CPUMotherboardGraphicsRAM
i5-6600k GIGABYTE G1.Sniper Z170 EVGA GeForce GTX 1070 FTW Corsair Vengeance LPX 16GB (2 x 8GB) DDR4-3000 
Hard DriveHard DriveOptical DriveCooling
Samsung 950 Pro 512GB M.2280 Seagate Barracuda 2TB 3.5" 7200RPM LG WH14NS40 Blu-Ray/DVD/CD Writer Phanteks PH-TC14PE_BL 
CoolingCoolingCoolingCooling
Phanteks PH-F140SP Phanteks PH-F140SP Phanteks PH-F140SP Phanteks PH-F140SP 
CoolingCoolingOSMonitor
Phanteks PH-F140SP Phanteks PH-F120SP Windows 10 Pro Visio E601i-A3 
KeyboardPowerCaseMouse
Logitech K400 EVGA SuperNOVA 750 G2 Phanteks Enthoo Luxe Logitech G600 MMO 
OtherOtherOther
XBox One Controller Reeven Four Eyes Touch HTC Vive 
CPUMotherboardRAMHard Drive
Pentium G4560 ASUS H110M-A/M.2 Corsair Vengeance LPX Western Digital Caviar Blue 
Hard DriveCoolingOSPower
Western Digital Caviar Blue Cryorig H7 Undecided EVGA Supernova G2 750W 
CaseOther
Corsair Air 540 Phanteks PH-F140SP 
CPUMotherboardGraphicsRAM
i3-2120 ACER IPISB-VR EVGA GTX 260 3x2GB DDR3 
Hard DriveOptical DriveOptical DriveCooling
Wester Digital Green ASUS DVD RW DVD RW Stock Cooler 
CoolingCoolingCoolingOS
Noctua NF-S12B Redux-1200 Noctua NF-S12B Redux-1200 Noctua NF-S12B Redux-1200 Windows 10 Pro 
PowerCaseMouse
Thermaltake TR2 500W Corsair Carbide Spec-01 Microsoft Intellimouse 
  hide details  
Reply
Gigabyte Z170
(23 items)
 
 
Brother's Machine
(15 items)
 
CPUMotherboardGraphicsRAM
i5-6600k GIGABYTE G1.Sniper Z170 EVGA GeForce GTX 1070 FTW Corsair Vengeance LPX 16GB (2 x 8GB) DDR4-3000 
Hard DriveHard DriveOptical DriveCooling
Samsung 950 Pro 512GB M.2280 Seagate Barracuda 2TB 3.5" 7200RPM LG WH14NS40 Blu-Ray/DVD/CD Writer Phanteks PH-TC14PE_BL 
CoolingCoolingCoolingCooling
Phanteks PH-F140SP Phanteks PH-F140SP Phanteks PH-F140SP Phanteks PH-F140SP 
CoolingCoolingOSMonitor
Phanteks PH-F140SP Phanteks PH-F120SP Windows 10 Pro Visio E601i-A3 
KeyboardPowerCaseMouse
Logitech K400 EVGA SuperNOVA 750 G2 Phanteks Enthoo Luxe Logitech G600 MMO 
OtherOtherOther
XBox One Controller Reeven Four Eyes Touch HTC Vive 
CPUMotherboardRAMHard Drive
Pentium G4560 ASUS H110M-A/M.2 Corsair Vengeance LPX Western Digital Caviar Blue 
Hard DriveCoolingOSPower
Western Digital Caviar Blue Cryorig H7 Undecided EVGA Supernova G2 750W 
CaseOther
Corsair Air 540 Phanteks PH-F140SP 
CPUMotherboardGraphicsRAM
i3-2120 ACER IPISB-VR EVGA GTX 260 3x2GB DDR3 
Hard DriveOptical DriveOptical DriveCooling
Wester Digital Green ASUS DVD RW DVD RW Stock Cooler 
CoolingCoolingCoolingOS
Noctua NF-S12B Redux-1200 Noctua NF-S12B Redux-1200 Noctua NF-S12B Redux-1200 Windows 10 Pro 
PowerCaseMouse
Thermaltake TR2 500W Corsair Carbide Spec-01 Microsoft Intellimouse 
  hide details  
Reply
post #12368 of 12386
Quote:
Originally Posted by dlewbell View Post

It looks like the lip on your case doesn't have nearly as large a cutout as mine does. Does it only taper in about 1/2" inside of the bolt holes? I'm starting to wonder if there was a revision to the case that changed that. The cutout on mine was wide enough that I'm certain that a full 140x140 framed fan would fit without issue, but it looks like you'd struggle to get more than a round framed fan in the same location.

You are correct, a full-framed fan would never fit in my case though without modifications to the case, fan, or both. I hope it was fixed in one of the revisions! I've actually been rather surprised by how many revisions this case has gone through. Usually a case in the lower-end price range that this one falls into doesn't get many updates or revisions, but I think Corsair has kept this one updated regularly due to the overwhelming success this case has had since it was first released.

My case is one of the first ones they sold at release. Back then the cables from the front panel were abysmally short and required a lot of modding just to do basic cable management if you wanted to use the front panel USB ports. The first revision of this case addressed this issue though by extending the length of the cables.
     
CPUMotherboardGraphicsRAM
Intel Core i5-6600K 6M Skylake Quad-Core 3.5 GH... ASUS Z170-PRO LGA 1151 Intel Z170 HDMI SATA 6Gb... ASUS ROG GeForce GTX 1070 STRIX-GTX1070-O8G-GAM... G.SKILL Ripjaws V Series 32GB (4 x 8GB) 288-Pin... 
Hard DriveHard DriveCoolingOS
SAMSUNG 850 PRO 2.5" 256GB SATA III 3-D Vertica... WD Black 1TB Performance Desktop Hard Disk Driv... Corsair Hydro Series H100i V2 Extreme Performan... Windows 10 Pro 64-bit 
MonitorKeyboardPowerCase
ASUS ROG PG278Q Black 27" WQHD 2560 x 1440, 144... Corsair K70 EVGA SuperNOVA 850 G2 Thermaltake Core X5 
Mouse
Logitech Proteus Core G502 
  hide details  
Reply
     
CPUMotherboardGraphicsRAM
Intel Core i5-6600K 6M Skylake Quad-Core 3.5 GH... ASUS Z170-PRO LGA 1151 Intel Z170 HDMI SATA 6Gb... ASUS ROG GeForce GTX 1070 STRIX-GTX1070-O8G-GAM... G.SKILL Ripjaws V Series 32GB (4 x 8GB) 288-Pin... 
Hard DriveHard DriveCoolingOS
SAMSUNG 850 PRO 2.5" 256GB SATA III 3-D Vertica... WD Black 1TB Performance Desktop Hard Disk Driv... Corsair Hydro Series H100i V2 Extreme Performan... Windows 10 Pro 64-bit 
MonitorKeyboardPowerCase
ASUS ROG PG278Q Black 27" WQHD 2560 x 1440, 144... Corsair K70 EVGA SuperNOVA 850 G2 Thermaltake Core X5 
Mouse
Logitech Proteus Core G502 
  hide details  
Reply
post #12369 of 12386
Quote:
Originally Posted by NaciremaDiputs View Post

You are correct, a full-framed fan would never fit in my case though without modifications to the case, fan, or both. I hope it was fixed in one of the revisions! I've actually been rather surprised by how many revisions this case has gone through. Usually a case in the lower-end price range that this one falls into doesn't get many updates or revisions, but I think Corsair has kept this one updated regularly due to the overwhelming success this case has had since it was first released.

My case is one of the first ones they sold at release. Back then the cables from the front panel were abysmally short and required a lot of modding just to do basic cable management if you wanted to use the front panel USB ports. The first revision of this case addressed this issue though by extending the length of the cables.
I had no idea this case had changed so much over the years. I bought mine used on a whim. I guess I lucked out & got one of the later revisions, as I have no cable length issues, & no fan fitment issues other than the side panel screw location.
Gigabyte Z170
(23 items)
 
 
Brother's Machine
(15 items)
 
CPUMotherboardGraphicsRAM
i5-6600k GIGABYTE G1.Sniper Z170 EVGA GeForce GTX 1070 FTW Corsair Vengeance LPX 16GB (2 x 8GB) DDR4-3000 
Hard DriveHard DriveOptical DriveCooling
Samsung 950 Pro 512GB M.2280 Seagate Barracuda 2TB 3.5" 7200RPM LG WH14NS40 Blu-Ray/DVD/CD Writer Phanteks PH-TC14PE_BL 
CoolingCoolingCoolingCooling
Phanteks PH-F140SP Phanteks PH-F140SP Phanteks PH-F140SP Phanteks PH-F140SP 
CoolingCoolingOSMonitor
Phanteks PH-F140SP Phanteks PH-F120SP Windows 10 Pro Visio E601i-A3 
KeyboardPowerCaseMouse
Logitech K400 EVGA SuperNOVA 750 G2 Phanteks Enthoo Luxe Logitech G600 MMO 
OtherOtherOther
XBox One Controller Reeven Four Eyes Touch HTC Vive 
CPUMotherboardRAMHard Drive
Pentium G4560 ASUS H110M-A/M.2 Corsair Vengeance LPX Western Digital Caviar Blue 
Hard DriveCoolingOSPower
Western Digital Caviar Blue Cryorig H7 Undecided EVGA Supernova G2 750W 
CaseOther
Corsair Air 540 Phanteks PH-F140SP 
CPUMotherboardGraphicsRAM
i3-2120 ACER IPISB-VR EVGA GTX 260 3x2GB DDR3 
Hard DriveOptical DriveOptical DriveCooling
Wester Digital Green ASUS DVD RW DVD RW Stock Cooler 
CoolingCoolingCoolingOS
Noctua NF-S12B Redux-1200 Noctua NF-S12B Redux-1200 Noctua NF-S12B Redux-1200 Windows 10 Pro 
PowerCaseMouse
Thermaltake TR2 500W Corsair Carbide Spec-01 Microsoft Intellimouse 
  hide details  
Reply
Gigabyte Z170
(23 items)
 
 
Brother's Machine
(15 items)
 
CPUMotherboardGraphicsRAM
i5-6600k GIGABYTE G1.Sniper Z170 EVGA GeForce GTX 1070 FTW Corsair Vengeance LPX 16GB (2 x 8GB) DDR4-3000 
Hard DriveHard DriveOptical DriveCooling
Samsung 950 Pro 512GB M.2280 Seagate Barracuda 2TB 3.5" 7200RPM LG WH14NS40 Blu-Ray/DVD/CD Writer Phanteks PH-TC14PE_BL 
CoolingCoolingCoolingCooling
Phanteks PH-F140SP Phanteks PH-F140SP Phanteks PH-F140SP Phanteks PH-F140SP 
CoolingCoolingOSMonitor
Phanteks PH-F140SP Phanteks PH-F120SP Windows 10 Pro Visio E601i-A3 
KeyboardPowerCaseMouse
Logitech K400 EVGA SuperNOVA 750 G2 Phanteks Enthoo Luxe Logitech G600 MMO 
OtherOtherOther
XBox One Controller Reeven Four Eyes Touch HTC Vive 
CPUMotherboardRAMHard Drive
Pentium G4560 ASUS H110M-A/M.2 Corsair Vengeance LPX Western Digital Caviar Blue 
Hard DriveCoolingOSPower
Western Digital Caviar Blue Cryorig H7 Undecided EVGA Supernova G2 750W 
CaseOther
Corsair Air 540 Phanteks PH-F140SP 
CPUMotherboardGraphicsRAM
i3-2120 ACER IPISB-VR EVGA GTX 260 3x2GB DDR3 
Hard DriveOptical DriveOptical DriveCooling
Wester Digital Green ASUS DVD RW DVD RW Stock Cooler 
CoolingCoolingCoolingOS
Noctua NF-S12B Redux-1200 Noctua NF-S12B Redux-1200 Noctua NF-S12B Redux-1200 Windows 10 Pro 
PowerCaseMouse
Thermaltake TR2 500W Corsair Carbide Spec-01 Microsoft Intellimouse 
  hide details  
Reply
post #12370 of 12386
Couple questions. What's the difference between the Air 540 and the Carbide Series CC-9011048-WW ?

Carbide

Air 540

Also, will a Corsair H115i extreme fit in a push pull config while clearing the RAM?



That photo is using a 100i with a push pull, and the 115 specs say it's around 6mm thinner, so I'm guessing yes?
Black Ivy
(11 items)
 
  
CPUMotherboardGraphicsRAM
i5 3750k ASRock Z77 Extreme6 GIGABYTE GV-N670OC-2GD Mushkin blackline 8GB 
Hard DriveHard DriveCoolingOS
Samsung F3 1TB Curcial M4 128GB SSD H100 Win7-64 bit 
MonitorPowerCase
ASUS 24" LED  Corsair HX750 Corsair Graphite 600T 
  hide details  
Reply
Black Ivy
(11 items)
 
  
CPUMotherboardGraphicsRAM
i5 3750k ASRock Z77 Extreme6 GIGABYTE GV-N670OC-2GD Mushkin blackline 8GB 
Hard DriveHard DriveCoolingOS
Samsung F3 1TB Curcial M4 128GB SSD H100 Win7-64 bit 
MonitorPowerCase
ASUS 24" LED  Corsair HX750 Corsair Graphite 600T 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Computer Cases
Overclock.net › Forums › Case Mods & Cases › Computer Cases › [Official] Corsair Carbide Air 540 Owner's Club +Gallery