Overclock.net › Forums › Case Mods & Cases › Computer Cases › [Official] Case PHANTEKS Case Club for lovers & owners
New Posts  All Forums:Forum Nav:

[Official] Case PHANTEKS Case Club for lovers & owners - Page 74

post #731 of 18654
hmm... I won't be able to tell you the combined height until I tear this tower down in november, but I can tell you that it comes with two thermal pads to sammich them together as you suggested. you should be able to get the different figures from Swiftech and add it up though. The whole coollabs thing I just read about hardening scares the hell out of me though. I'm using it between all my waterblocks (titans & 3570k) and just picked up two more tubes (one of which has leaked a bit) for my rebuild. I'm literally going to cry if I have to chip away @ my dye's... That being said, I have faith that my bottle of Indigo Extreme Clean will do it's job.

Edit: He say's he was pushing insane temp's... My gpu's never break 50, and my cpu never breaks 60... Hopefully i'm in the clear. I'll be using Indigo Extreme ETI for my 3930k, it's too bad the strips are not one size fit's all. I literally have 100$ worth of them for 3570k sized chips.
Edited by skupples - 10/19/13 at 9:06pm
IT'S WHITE
(21 items)
 
 
CPUMotherboardGraphicsGraphics
4930k Rampage iv extreme Black Edition GTX Titan  GTX Titan 
GraphicsRAMHard DriveHard Drive
GTX Titan GskillZ Trident X Samsung EVO samsung 840 evo 
Optical DriveCoolingCoolingOS
Asus External Blue Ray drive 4x 480x60mm Swiftech MCP35x2 Win 8.1.2 
MonitorMonitorMonitorPower
AOC AOC AOC EVGA G2 1300w 
CaseMouseMouse PadAudio
STH10 RAT7 what is this?  Vali / Modi :(  
Other
Corsair HX850 
  hide details  
Reply
IT'S WHITE
(21 items)
 
 
CPUMotherboardGraphicsGraphics
4930k Rampage iv extreme Black Edition GTX Titan  GTX Titan 
GraphicsRAMHard DriveHard Drive
GTX Titan GskillZ Trident X Samsung EVO samsung 840 evo 
Optical DriveCoolingCoolingOS
Asus External Blue Ray drive 4x 480x60mm Swiftech MCP35x2 Win 8.1.2 
MonitorMonitorMonitorPower
AOC AOC AOC EVGA G2 1300w 
CaseMouseMouse PadAudio
STH10 RAT7 what is this?  Vali / Modi :(  
Other
Corsair HX850 
  hide details  
Reply
post #732 of 18654
Dang.... storming here so submitted message before I was done .... you were too quick for me .....you answered before I finished edits smile.gif

Swiftech has no height dimension on stand ..... only the sink.... well I know the height of the pump, if ya get curios and play with the stand.... I can add smile.gif
911 Carrera
(20 items)
 
  
CPUMotherboardGraphicsRAM
Intel w/ EK Supremacy Cooling Block - Clean P... Asus Maximus VI Formula 2 x Asus GTX 780 DCII w/ EK Full Cover Blocks a... Mushkin Red Line Ridgeback 2 x 8GB DDR302400 10... 
Hard DriveHard DriveOptical DriveCooling
2 x SAMSUNG 840 Pro Series MZ-7PD256BW 2.5" 256GB (2 x Seagate ST2000DX001 2TB 7200 RPM 64MB Cach... Asus BW-12B1ST/BLK/G/AS Blue Ray Writer 1 x Alphacool NexXxoS XT45-420 + 1 x Alphacool ... 
CoolingCoolingCoolingCooling
1 x Swiftech 35x2 w/ Heatsink and NB Fan EK -MultiOption RES X3 250 White Acetal Reservoir 5 x PH-F140SP_BK_BLED + 5 x PH-F140SP_BK E22 Rigid 10/12 Acrylic Tubing and Bitspower Ma... 
CoolingOSMonitorKeyboard
2 x Reeven Six Eyes Fan Controller Windows 7 64 Bit Professional OEM ASUS VG248QE Black 23" 144 Hz Monitor Logitech G19s 920-004985 
PowerCaseMouseAudio
Seasonic X-1250 Phanteks Enthoo Primo Ultimate Chassis Asus RoG GX950 Laser Mouse  Logitech Z5500 
  hide details  
Reply
911 Carrera
(20 items)
 
  
CPUMotherboardGraphicsRAM
Intel w/ EK Supremacy Cooling Block - Clean P... Asus Maximus VI Formula 2 x Asus GTX 780 DCII w/ EK Full Cover Blocks a... Mushkin Red Line Ridgeback 2 x 8GB DDR302400 10... 
Hard DriveHard DriveOptical DriveCooling
2 x SAMSUNG 840 Pro Series MZ-7PD256BW 2.5" 256GB (2 x Seagate ST2000DX001 2TB 7200 RPM 64MB Cach... Asus BW-12B1ST/BLK/G/AS Blue Ray Writer 1 x Alphacool NexXxoS XT45-420 + 1 x Alphacool ... 
CoolingCoolingCoolingCooling
1 x Swiftech 35x2 w/ Heatsink and NB Fan EK -MultiOption RES X3 250 White Acetal Reservoir 5 x PH-F140SP_BK_BLED + 5 x PH-F140SP_BK E22 Rigid 10/12 Acrylic Tubing and Bitspower Ma... 
CoolingOSMonitorKeyboard
2 x Reeven Six Eyes Fan Controller Windows 7 64 Bit Professional OEM ASUS VG248QE Black 23" 144 Hz Monitor Logitech G19s 920-004985 
PowerCaseMouseAudio
Seasonic X-1250 Phanteks Enthoo Primo Ultimate Chassis Asus RoG GX950 Laser Mouse  Logitech Z5500 
  hide details  
Reply
post #733 of 18654
Quote:
Originally Posted by JackNaylorPE View Post

BTW, two questions for ya......

1. What EK Supremacy Water Block ya gonna use with the Nekid Ivy ? Looking at the video review by singularity it would seem to me that teh bloakc would perform better rotated 90 degrees so that the fins inside ran parallel with the long length of the naked CPU

2. What TIM ya use on GPU Blocks .....

I had my heart set on the Asus GTX 770 Poseidons .... but not a word since Comdex back in June. So now with 780 GTi about to drop I'm wondering if that will be its debut..... never did a WB on a GPU and haven't as yet done mush research on which manufacturer's have proven most reliable, WB manufacturer's backplate or card manufacturers ..... tubing or bridge.

Looking at the water block roundup on xtremereviews, rotating the supracy 90 degrees ccw does improve temps, so I'm going to go for that

I have the copper base and clean black acetal top variant, I got a very good deal on it, it looks great and all my other blocks and rads are copper, so I wanted my nimise the use of nickel wherever possible

For GPU paste, my 680s have some reistors or something around the edge of the die, therecore I wanted to use a non conductive Tim
I have a big tube of Arctic mx-4, so I'm just going to use that for the GPUs, and the bundled gelid GC extreme for my bare CPU die
post #734 of 18654
Quote:
Originally Posted by JackNaylorPE View Post

[...]
Fill / Bleed Ports - Jesse, since you have been in there .... how hard would it be to get the fill and air bleed ports in as I showed in the image on Post #700 ?

Radiator Top Port - Male x Female Extender - Plug Fitting

Seems it would be be easier with ports towards the front but that would prolly require a reservoir mounted off back of 5.25 cages

That's exactly how I'll be doing my fill ports, as I had posted some many posts back now. I'm actually planning on putting one for each of the top-facing ports on my 480 rad, as I suspect it will be easier to fill if I have one port for filling and one to let air escape out of. I have a klein knockout punch set so I suspect it won't be too hard for me to put a couple clean 1" holes wherever I want them for these .8" ID grommets:
http://www.frozencpu.com/products/4328/ele-229/PVC_Rubber_Grommet_-_08125_ID_Hole.html?id=5BLerN5a&mv_pc=102
Though you could probably do holes just as well with a hole-saw drill bit if you're careful to use painter's tape, drill a pilot hole, etc.

I also have a small G1/4 threaded funnel to be able to screw into one of the extensions to help make filling easier.

In addition I'm also hoping to be able to mount my lower 360 monsta rad with the inlet/outlet ports towards the front of the case so that the monsta's drain port would face the back and I can also put a hole right through the back of the case with a grommet for an extension to poke through to use as a drain - though I'm not sure that's going to be a possibility or not yet as to how the fan/rad mounting holes in the bottom of the case are located or not.

If need be I can always just mount the rad the other way, with the inlet/outlet ports to the rear, and in that case I'll probably just use one of the rear facing ports the same way. The only thing about doing it that way is is would only drain the upper half of that lower rad without some serious tipping of the case, but that shouldn't be a huge deal I don't suspect. Maybe even get away with putting a fitting in one of the downward facing ports instead so that I might be able to drain it right out of the bottom of the case with the bottom air filter removed so I can drain the loop completely that way, but I dunno. I won't be able to solidify what exactly I'll be doing until I get my hands on the case.
Edited by Unicr0nhunter - 10/20/13 at 5:51am
post #735 of 18654
Waiting patiently for this case! So while im waiting was thinking about rinsing out my new Rads and waterblocks,do u guys think they will get rusty if i clean them out and they sit a week before they are installed?
Primo
(15 items)
 
  
CPUMotherboardGraphicsRAM
I7-7700k Asus Maximus Hero ix Evga GTX 1080 ACX 3.0 G-Skill F-43200C15D-16GTZKW 
Hard DriveHard DriveCoolingCooling
Samsung 850 Evo Corsair Neutron  Ek Supremacy CSQ clean OCOOL 360mm radiator 
CoolingCoolingOSKeyboard
OCOOL 360mm radiator Ek -FC1080 GTX  Windows 10 CM Storm 
PowerCaseMouse
Evga 750 watt Phanteks Enthoo Primo Roccat Kone Optical 
  hide details  
Reply
Primo
(15 items)
 
  
CPUMotherboardGraphicsRAM
I7-7700k Asus Maximus Hero ix Evga GTX 1080 ACX 3.0 G-Skill F-43200C15D-16GTZKW 
Hard DriveHard DriveCoolingCooling
Samsung 850 Evo Corsair Neutron  Ek Supremacy CSQ clean OCOOL 360mm radiator 
CoolingCoolingOSKeyboard
OCOOL 360mm radiator Ek -FC1080 GTX  Windows 10 CM Storm 
PowerCaseMouse
Evga 750 watt Phanteks Enthoo Primo Roccat Kone Optical 
  hide details  
Reply
post #736 of 18654
Quote:
Originally Posted by OutlawII View Post

Waiting patiently for this case! So while im waiting was thinking about rinsing out my new Rads and waterblocks,do u guys think they will get rusty if i clean them out and they sit a week before they are installed?

I cleaned mine and they have been sitting for a week or so now, just cap them or run a short hose on the ends to cap it.
post #737 of 18654
Thanks dude just posted in the H2O section also.
Primo
(15 items)
 
  
CPUMotherboardGraphicsRAM
I7-7700k Asus Maximus Hero ix Evga GTX 1080 ACX 3.0 G-Skill F-43200C15D-16GTZKW 
Hard DriveHard DriveCoolingCooling
Samsung 850 Evo Corsair Neutron  Ek Supremacy CSQ clean OCOOL 360mm radiator 
CoolingCoolingOSKeyboard
OCOOL 360mm radiator Ek -FC1080 GTX  Windows 10 CM Storm 
PowerCaseMouse
Evga 750 watt Phanteks Enthoo Primo Roccat Kone Optical 
  hide details  
Reply
Primo
(15 items)
 
  
CPUMotherboardGraphicsRAM
I7-7700k Asus Maximus Hero ix Evga GTX 1080 ACX 3.0 G-Skill F-43200C15D-16GTZKW 
Hard DriveHard DriveCoolingCooling
Samsung 850 Evo Corsair Neutron  Ek Supremacy CSQ clean OCOOL 360mm radiator 
CoolingCoolingOSKeyboard
OCOOL 360mm radiator Ek -FC1080 GTX  Windows 10 CM Storm 
PowerCaseMouse
Evga 750 watt Phanteks Enthoo Primo Roccat Kone Optical 
  hide details  
Reply
post #738 of 18654
I got the Primochill Primo flex tubing and it says you need to run the cleaner in it. I let it run through the new tubing and all my components for at least 24 hours as instructed then just capped the rads. Also gave me time to clean my cpu block good.

Fingers crossed for an earlier delivery, possibly Wednesday!
post #739 of 18654
Quote:
Originally Posted by bond32 View Post

I got the Primochill Primo flex tubing and it says you need to run the cleaner in it. I let it run through the new tubing and all my components for at least 24 hours as instructed then just capped the rads. Also gave me time to clean my cpu block good.

Fingers crossed for an earlier delivery, possibly Wednesday!

Interesting i got the same tubing but the advanced,yep waiting for this case is killin me!
Primo
(15 items)
 
  
CPUMotherboardGraphicsRAM
I7-7700k Asus Maximus Hero ix Evga GTX 1080 ACX 3.0 G-Skill F-43200C15D-16GTZKW 
Hard DriveHard DriveCoolingCooling
Samsung 850 Evo Corsair Neutron  Ek Supremacy CSQ clean OCOOL 360mm radiator 
CoolingCoolingOSKeyboard
OCOOL 360mm radiator Ek -FC1080 GTX  Windows 10 CM Storm 
PowerCaseMouse
Evga 750 watt Phanteks Enthoo Primo Roccat Kone Optical 
  hide details  
Reply
Primo
(15 items)
 
  
CPUMotherboardGraphicsRAM
I7-7700k Asus Maximus Hero ix Evga GTX 1080 ACX 3.0 G-Skill F-43200C15D-16GTZKW 
Hard DriveHard DriveCoolingCooling
Samsung 850 Evo Corsair Neutron  Ek Supremacy CSQ clean OCOOL 360mm radiator 
CoolingCoolingOSKeyboard
OCOOL 360mm radiator Ek -FC1080 GTX  Windows 10 CM Storm 
PowerCaseMouse
Evga 750 watt Phanteks Enthoo Primo Roccat Kone Optical 
  hide details  
Reply
post #740 of 18654
Quote:
Originally Posted by OutlawII View Post

Interesting i got the same tubing but the advanced,yep waiting for this case is killin me!
Same! I've got 1/2" advanced in white, I didnt know you had to flush it?
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Computer Cases
Overclock.net › Forums › Case Mods & Cases › Computer Cases › [Official] Case PHANTEKS Case Club for lovers & owners