Overclock.net › Forums › Case Mods & Cases › Sponsored Builds & Case Mods › [Build Log] Project Rampage II - GTX 780TI Tri SLI, Caselabs STH10, , Custom Mods
New Posts  All Forums:Forum Nav:

[Build Log] Project Rampage II - GTX 780TI Tri SLI, Caselabs STH10, , Custom Mods - Page 14

post #131 of 164
Thanks! +REP

Do you just glue the LED to the water blocks?
post #132 of 164
Quote:
Originally Posted by kaiqi07 View Post

Thank you, I removed the GEFORCE GTX led from the default cooler and did a simple mod to mount them onto my water blocks. Just felt the slots between the PCI E slots were a bit too dim for my liking thus doing this mod to brighten them.

I tried this and I cant get it to stay, do you recommend a particular adhesive tap or glue?
Edited by GradySac - 2/25/14 at 1:41pm
post #133 of 164
Thread Starter 
I used an acrylic double sided tape to secure the LED to the block. It is industrial kind of tape so it held on pretty secure to my block. I do not advise using glue as the cards produces heat and I bet the glue will come off as well.
post #134 of 164
Correct me if I'm wrong but it looks like you have the left d5 pump connected via both inlets, effectively bypassing the pump entirely.
NanoBench
(21 items)
 
STHTV
(8 items)
 
CPUMotherboardGraphicsRAM
2600k maximus iv gene Gtx 780 Classified G.Skill Trident X 
Hard DriveCoolingCoolingCooling
adata sx900 Watercool MO-RA3 420 bitspower tank Swiftech MCP35x2 
CoolingCoolingCoolingCooling
EK-Ram Monarch x4 Clean Ek MIV-Gene Fullboard EK 780 Classified VGA Cooler EK Supremacy Clean 
CoolingMonitorKeyboardPower
Aquaero 5 LT Crossover 1440p QuickFire Tenkeyless Seasonic x-750 
CaseMouseMouse PadAudio
Dimastech Nano g700 Mionix Propus 380 Onkyo HT-R290 
Other
MDPC Sleeve 
CPUMotherboardGraphicsRAM
2500k asrock z77e-itx gtx 650 ti boost gskill ripjaws x 
Hard DriveOSMonitorCase
adata sx900 256 antec khuler Sony Bravia silverstone sg05 
  hide details  
Reply
NanoBench
(21 items)
 
STHTV
(8 items)
 
CPUMotherboardGraphicsRAM
2600k maximus iv gene Gtx 780 Classified G.Skill Trident X 
Hard DriveCoolingCoolingCooling
adata sx900 Watercool MO-RA3 420 bitspower tank Swiftech MCP35x2 
CoolingCoolingCoolingCooling
EK-Ram Monarch x4 Clean Ek MIV-Gene Fullboard EK 780 Classified VGA Cooler EK Supremacy Clean 
CoolingMonitorKeyboardPower
Aquaero 5 LT Crossover 1440p QuickFire Tenkeyless Seasonic x-750 
CaseMouseMouse PadAudio
Dimastech Nano g700 Mionix Propus 380 Onkyo HT-R290 
Other
MDPC Sleeve 
CPUMotherboardGraphicsRAM
2500k asrock z77e-itx gtx 650 ti boost gskill ripjaws x 
Hard DriveOSMonitorCase
adata sx900 256 antec khuler Sony Bravia silverstone sg05 
  hide details  
Reply
post #135 of 164
Thread Starter 
Quote:
Originally Posted by SeeThruHead View Post

Correct me if I'm wrong but it looks like you have the left d5 pump connected via both inlets, effectively bypassing the pump entirely.


Sharp eye haha, yes I connected wrongly and had changed the inlet/outlet few weeks ago.
post #136 of 164
What did you use to controll the RGB led strip? Were yo able to connect it to the aquaero 6 RGB header or did you have to use a 3rd party controller? Im trying to setup a light a RGB LED box and RGB LED strips. Thanks!
post #137 of 164
I need to check the sponsored build log forum more often. Can't believe I missed this one until now. That cable pass through panel is absolutely sick. Brilliant stuff in here.
post #138 of 164
Thread Starter 
Quote:
Originally Posted by GradySac View Post

What did you use to controll the RGB led strip? Were yo able to connect it to the aquaero 6 RGB header or did you have to use a 3rd party controller? Im trying to setup a light a RGB LED box and RGB LED strips. Thanks!


I had used a Aquaero LED Amp made by a DIY modder from Germany. As Aquaero LED allows and only support a single LED bulb, this Aquaero LED Amp supports up to 20m of LEDs.

It had its own molex power and had three RGB output. Very useful if you intend to use RGB LED strips in your build. I am using it to lit up my front panel vents, rear panel as well as my Aquaero 5/6 front panel plates.

Using the GPU temps as source and using the LEDs to indicate the various temperatures of my GPU.

30c (normal) - White LED
38c (warm) - Orange LED
45c (Hot) - Red LED

By doing this, I dont have to keep checking on my system temps as the different LED that are litting up could lemme knw what is my GPU temps.
post #139 of 164
Thanks for the reply! Also by chance is the LED AMP made by drdeath? And what brand of RGB LEDs are you using?
post #140 of 164
Thread Starter 
All I know his name is Jake and I PM him in the AQC forum. I am using those 5050 RGB strips, brand wise I am unsure. Anyway most and close to all LEDs are made in China, dont they.
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Sponsored Builds & Case Mods
Overclock.net › Forums › Case Mods & Cases › Sponsored Builds & Case Mods › [Build Log] Project Rampage II - GTX 780TI Tri SLI, Caselabs STH10, , Custom Mods