Overclock.net › Forums › Intel › Intel Motherboards › [Official] Asus Rampage IV Black Edition Owners Club!
New Posts  All Forums:Forum Nav:

[Official] Asus Rampage IV Black Edition Owners Club! - Page 583

post #5821 of 14761
Thread Starter 
I give up with my chip, up to 1.48v and still can't boot into windows @ 5.0 haven't tried under though. If I increase blck to 125 it doesn't boot, and these half second bootup half second shutsdown x repeat x 20 till I unplug the back is pissing me off at times, you'd figure they'd give it a few seconds to keep from killing other hardware ==;;;
Sylphiel
(20 items)
 
Yuna
(18 items)
 
 
CPUMotherboardGraphicsRAM
Intel Core i7 Extreme 980X Gigabyte X58A-UD3R eVGA GTX TITAN Corsair 
RAMHard DriveOptical DriveCooling
Corsair  Corsair SSD Samsung BluRay R/W Corsair H90 
OSMonitorMonitorMonitor
Windows 7 Ultimate HP w2338h HP w2338h HP w2338h 
MonitorMonitorKeyboardPower
HP w2338h Samsung 46" TV ROCCAT Antex 1200W Silver 
CaseMouseMouse PadAudio
Cosmos Corsair m95 ALLSOP Onboard 
  hide details  
Reply
Sylphiel
(20 items)
 
Yuna
(18 items)
 
 
CPUMotherboardGraphicsRAM
Intel Core i7 Extreme 980X Gigabyte X58A-UD3R eVGA GTX TITAN Corsair 
RAMHard DriveOptical DriveCooling
Corsair  Corsair SSD Samsung BluRay R/W Corsair H90 
OSMonitorMonitorMonitor
Windows 7 Ultimate HP w2338h HP w2338h HP w2338h 
MonitorMonitorKeyboardPower
HP w2338h Samsung 46" TV ROCCAT Antex 1200W Silver 
CaseMouseMouse PadAudio
Cosmos Corsair m95 ALLSOP Onboard 
  hide details  
Reply
post #5822 of 14761
Press power button for 4 seconds (emergency shut down) LunaP, this board does that ONLY when you do something weird, or when RAM is missconfigured.

BTW have you tried to increase current capability from 140 to 170? Just to test if you will still have these problem with RAM speed.
Quote:
Originally Posted by Ajay57 View Post

My first CPU was a 4930K sorry to say it was a DOG of a chip only OC to 4.6 Mhz, then i managed to find this one and it goes up to 4.7 easy @ about 1.4v. But after that it jumps to 1.510v to get to 4.8 Mhz and with the LLC it goes up to 1.525v,I can not go to 4.9 as i have not tried that yet and do not know if it would be possible at this stage.
That's killing voltage. You should think about going into liquid nitrogen, to get HWbot points. Are you using LLC on regular? If not these voltages are quite a lot for Ivy even under water cooling.
Edited by Raghar - 2/19/14 at 11:46am
post #5823 of 14761
Thread Starter 
Quote:
Originally Posted by Raghar View Post

Press power button for 4 seconds (emergency shut down) LunaP, this board does that ONLY when you do something weird, or when RAM is missconfigured.

BTW have you tried to increase current capability from 140 to 170? Just to test if you will still have these problem with RAM speed.

huh?

Also I know you can hold down the power button for 4 seconds derp, I said it does it in half a second = useless, which I have to flip the switch on the back of the PSU.

THe only weird thing I did was leave the same voltage and flip the block up to 125 vs 100 as well as lower RAM speeds down to comply. I'm running RAM @ default to avoid issues (1333) when testing.

what is this 140 to 170 you speaketh of?
Sylphiel
(20 items)
 
Yuna
(18 items)
 
 
CPUMotherboardGraphicsRAM
Intel Core i7 Extreme 980X Gigabyte X58A-UD3R eVGA GTX TITAN Corsair 
RAMHard DriveOptical DriveCooling
Corsair  Corsair SSD Samsung BluRay R/W Corsair H90 
OSMonitorMonitorMonitor
Windows 7 Ultimate HP w2338h HP w2338h HP w2338h 
MonitorMonitorKeyboardPower
HP w2338h Samsung 46" TV ROCCAT Antex 1200W Silver 
CaseMouseMouse PadAudio
Cosmos Corsair m95 ALLSOP Onboard 
  hide details  
Reply
Sylphiel
(20 items)
 
Yuna
(18 items)
 
 
CPUMotherboardGraphicsRAM
Intel Core i7 Extreme 980X Gigabyte X58A-UD3R eVGA GTX TITAN Corsair 
RAMHard DriveOptical DriveCooling
Corsair  Corsair SSD Samsung BluRay R/W Corsair H90 
OSMonitorMonitorMonitor
Windows 7 Ultimate HP w2338h HP w2338h HP w2338h 
MonitorMonitorKeyboardPower
HP w2338h Samsung 46" TV ROCCAT Antex 1200W Silver 
CaseMouseMouse PadAudio
Cosmos Corsair m95 ALLSOP Onboard 
  hide details  
Reply
post #5824 of 14761
Quote:
Originally Posted by LaBestiaHumana View Post

My new chip is running Cinebench runs at 4.8 with 1.36v. I'm definitely keeping and selling my old one.

Twice my PC shut down and rebooted on its own, no blue screen or anything. Has anyone experienced random shut downs?

Good chip.

Had random shutdowns myself. Traced it to one of the drivers the BE comes with. Can't remember if it was chipset or not. Whichever one it was i omitted it on a clean install and no problems since.
post #5825 of 14761
Quote:
Originally Posted by LunaP View Post

I give up with my chip, up to 1.48v and still can't boot into windows @ 5.0 haven't tried under though. If I increase blck to 125 it doesn't boot, and these half second bootup half second shutsdown x repeat x 20 till I unplug the back is pissing me off at times, you'd figure they'd give it a few seconds to keep from killing other hardware ==;;;

Mine runs at 5.0, but not benchmark stable.
Quote:
Originally Posted by Doug2507 View Post

Good chip.

Had random shutdowns myself. Traced it to one of the drivers the BE comes with. Can't remember if it was chipset or not. Whichever one it was i omitted it on a clean install and no problems since.

I might just do another clean install and see if it helps. Thanks for the input. thumb.gif
post #5826 of 14761
Thanks Doug for the LINK just blew away my scores on 3D MARK 11, just tried the settings of our friend in STOKE!!! Works a treat now i am more stable and not dropping so many FPS like before, it was like being on a ROLLERCOASTER!!

1,


2,


Got some really nice points to add to my score!!


Regards,


AJ.
post #5827 of 14761
Quote:
Originally Posted by LunaP View Post

what is this 140 to 170 you speaketh of?

Look here at CPU current capability, a slight increase just for few minutes of testing shouldn't hurt. You can also try set VCCSA current to 120, which might help with 64 GB RAM. It also creates more stress however.
post #5828 of 14761
VCSSA @ Auto + offset @ Auto , how can I check the real value used? does the board auto set the VCSSA like it does with the vcore if I just change the multiplier?
Taichi
(15 items)
 
  
CPUMotherboardGraphicsRAM
i7 5960x ASRock X99 Taichi EVGA GTX 1070 FTW Kingston 32GB Fury X 2666MHz 
Hard DriveHard DriveHard DriveCooling
Samsung 960 Pro 512Gb Samsung SSD 850 EVO 500Gb Seagate Enterprise Capacity v5 8Tb  Nzxt Kraken X62 
OSMonitorPowerCase
Windows 7 / Windows 10 Pro LG 29UM67 Seasonic Prime Titanium 850w Corsair Obsidian 750D 
MouseAudio
Logitech G502 Proteus Spectrum Creative Sound Blaster ZxR 
  hide details  
Reply
Taichi
(15 items)
 
  
CPUMotherboardGraphicsRAM
i7 5960x ASRock X99 Taichi EVGA GTX 1070 FTW Kingston 32GB Fury X 2666MHz 
Hard DriveHard DriveHard DriveCooling
Samsung 960 Pro 512Gb Samsung SSD 850 EVO 500Gb Seagate Enterprise Capacity v5 8Tb  Nzxt Kraken X62 
OSMonitorPowerCase
Windows 7 / Windows 10 Pro LG 29UM67 Seasonic Prime Titanium 850w Corsair Obsidian 750D 
MouseAudio
Logitech G502 Proteus Spectrum Creative Sound Blaster ZxR 
  hide details  
Reply
post #5829 of 14761
Quote:
Originally Posted by Ajay57 View Post

Thanks Doug for the LINK just blew away my scores on 3D MARK 11, just tried the settings of our friend in STOKE!!! Works a treat now i am more stable and not dropping so many FPS like before, it was like being on a ROLLERCOASTER!!

1,


2,


Got some really nice points to add to my score!!


Regards,


AJ.

Lol, 10/10 for effort Philip but you've only gained about .3 globals for each one!! tongue.gif You only get the difference between last score and new one added!! thumb.gif (just goes to show an extra bin on gpu and 100mhz on core doesn't make much difference!)
post #5830 of 14761
CPU Current :

140% = 100%.
150% = 110%
160% = 120%
170% = 130%
180% = 140%


130% = 90%
120% = 80%(VRM can now be manually adjusted)
110% = 70%
100% = 60%.



Hence why when that setting is changed from "AUTO", things don't work right. It's a noob-catcher.

Keep in mind, this is ASUS. They sell VGA cards with built-in mod points, then lock the BIOS so you can't use them effectively without flashing the BIOS (MATRIX 7970), or they sell cards that offer no voltage adjustment with mod points(DIRECT CUII 7970).


So, the hardware and options are there, if you know the tricks. If you don't, you're not likely to break anything. And if you do break something, it's clearly your own fault (in ASUS' eyes. Anyone that's gone through RMA understands).


thumb.gif
Quote:
Originally Posted by LunaP View Post

huh?

Also I know you can hold down the power button for 4 seconds derp, I said it does it in half a second = useless, which I have to flip the switch on the back of the PSU.

THe only weird thing I did was leave the same voltage and flip the block up to 125 vs 100 as well as lower RAM speeds down to comply. I'm running RAM @ default to avoid issues (1333) when testing.

what is this 140 to 170 you speaketh of?

He's right. Even if it shuts down, you simply hold the button down until it stops the boot loop, or you hold down CMOS Clear on back panel. It can reboot 5 times in that 5 seconds, board doesn't shut down on boot loops for LN2 use, so to stop the loop you hold the power button ON THE BOARD ITSELF.

Power button on OC panel and front panel doesn't work the same, unfortunately.

At times I think bits of LN2 Mode stay on always. tongue.gif
Quote:
Originally Posted by boldenc View Post

VCSSA @ Auto + offset @ Auto , how can I check the real value used? does the board auto set the VCSSA like it does with the vcore if I just change the multiplier?

Clear CMOS, boot into BIOS. value given in BIOS monitoring panel is just a bit higher than stock value, since board sets "EXTREME" loadline calibration by default. You can try adjusting loadline values to compensate.

And yeah, AUTO settings adjust VCCSA automatically. It's "AUTO", man!
Edited by cadaveca - 2/19/14 at 2:26pm
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel Motherboards
Overclock.net › Forums › Intel › Intel Motherboards › [Official] Asus Rampage IV Black Edition Owners Club!