Overclock.net › Forums › Software, Programming and Coding › Networking & Security › Linksys E2500 DHCP WAN status stuck on renewing
New Posts  All Forums:Forum Nav:

Linksys E2500 DHCP WAN status stuck on renewing

post #1 of 6
Thread Starter 
Hey guys,

I recently bought a Linksys E2500 to replace my aging router. It is hooked up directly to the data port located in the living room of my apartment (no modem). I immediately flashed TomatoUSB to it and it was working fine until just yesterday. I unplugged the router to clean the surrounding areas, and when I plugged the router back in, the internet was not working. The wireless network is being broadcasted, and I am able to connect to it, but no pages load. I am able to access the router's administrative page and can see that the DHCP lease is stuck on renewing. Releasing and renewing the lease does nothing. If I hook up another device directly to the data port, the internet will work fine. I've tried resetting the router back to factory settings, clearing the NVRAM, and applying several firewall related scripts, but I can't get it to work. I also tried upgrading the firmware, but the upload process will hang (I waited more than an hour on one occasion).

Here are the log files from the last time I rebooted it: Warning: Spoiler! (Click to show)
Jan 1 01:00:49 unknown syslog.info syslogd started: BusyBox v1.21.1
Jan 1 01:00:49 unknown user.notice kernel: klogd started: BusyBox v1.21.1 (2014-01-19 19:30:20 CET)
Jan 1 01:00:49 unknown user.notice kernel: Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #74 Sun Jan 19 19:38:58 CET 2014
Jan 1 01:00:49 unknown user.warn kernel: CPU revision is: 00019749
Jan 1 01:00:49 unknown user.warn kernel: wombo_reset set to gpio 23
Jan 1 01:00:49 unknown user.warn kernel: Determined physical RAM map:
Jan 1 01:00:49 unknown user.warn kernel: memory: 04000000 @ 00000000 (usable)
Jan 1 01:00:49 unknown user.debug kernel: Entering add_active_range(0, 0, 16384) 0 entries of 256 used
Jan 1 01:00:49 unknown user.info kernel: Zone PFN ranges:
Jan 1 01:00:49 unknown user.warn kernel: Normal 0 -> 16384
Jan 1 01:00:49 unknown user.warn kernel: HighMem 16384 -> 16384
Jan 1 01:00:49 unknown user.info kernel: early_node_map[1] active PFN ranges
Jan 1 01:00:49 unknown user.warn kernel: 0: 0 -> 16384
Jan 1 01:00:49 unknown user.debug kernel: On node 0 totalpages: 16384
Jan 1 01:00:49 unknown user.debug kernel: Normal zone: 0 pages used for memmap
Jan 1 01:00:49 unknown user.debug kernel: Normal zone: 0 pages reserved
Jan 1 01:00:49 unknown user.debug kernel: Normal zone: 16384 pages, LIFO batch:3
Jan 1 01:00:49 unknown user.debug kernel: HighMem zone: 0 pages used for memmap
Jan 1 01:00:49 unknown user.warn kernel: Built 1 zonelists. Total pages: 16384
Jan 1 01:00:49 unknown user.notice kernel: Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
Jan 1 01:00:49 unknown user.warn kernel: Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Jan 1 01:00:49 unknown user.warn kernel: Primary data cache 32kB, 4-way, linesize 32 bytes.
Jan 1 01:00:49 unknown user.info kernel: Synthesized TLB refill handler (20 instructions).
Jan 1 01:00:49 unknown user.info kernel: Synthesized TLB load handler fastpath (32 instructions).
Jan 1 01:00:49 unknown user.info kernel: Synthesized TLB store handler fastpath (32 instructions).
Jan 1 01:00:49 unknown user.info kernel: Synthesized TLB modify handler fastpath (31 instructions).
Jan 1 01:00:49 unknown user.warn kernel: PID hash table entries: 512 (order: 9, 2048 bytes)
Jan 1 01:00:49 unknown user.warn kernel: CPU: BCM5357 rev 2 pkg 8 at 300 MHz
Jan 1 01:00:49 unknown user.warn kernel: Using 150.000 MHz high precision timer.
Jan 1 01:00:49 unknown user.info kernel: console [ttyS0] enabled
Jan 1 01:00:49 unknown user.warn kernel: Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Jan 1 01:00:49 unknown user.warn kernel: Mount-cache hash table entries: 512
Jan 1 01:00:49 unknown user.info kernel: NET: Registered protocol family 16
Jan 1 01:00:49 unknown user.warn kernel: PCI: no core
Jan 1 01:00:49 unknown user.warn kernel: PCI: no core
Jan 1 01:00:49 unknown user.warn kernel: PCI: Fixing up bus 0
Jan 1 01:00:49 unknown user.info kernel: NET: Registered protocol family 2
Jan 1 01:00:49 unknown user.info kernel: Time: MIPS clocksource has been installed.
Jan 1 01:00:49 unknown user.warn kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan 1 01:00:50 unknown user.warn kernel: TCP established hash table entries: 2048 (order: 2, 16384 bytes)
Jan 1 01:00:50 unknown user.warn kernel: TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
Jan 1 01:00:50 unknown user.info kernel: TCP: Hash tables configured (established 2048 bind 2048)
Jan 1 01:00:50 unknown user.info kernel: TCP reno registered
Jan 1 01:00:50 unknown user.info kernel: squashfs: version 3.0 (2006/03/15) Phillip Lougher
Jan 1 01:00:50 unknown user.info kernel: io scheduler noop registered (default)
Jan 1 01:00:50 unknown user.info kernel: HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
Jan 1 01:00:50 unknown user.info kernel: N_HDLC line discipline registered.
Jan 1 01:00:50 unknown user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Jan 1 01:00:50 unknown user.info kernel: serial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A
Jan 1 01:00:50 unknown user.info kernel: PPP generic driver version 2.4.2
Jan 1 01:00:50 unknown user.info kernel: MPPE/MPPC encryption/compression module registered
Jan 1 01:00:50 unknown user.info kernel: NET: Registered protocol family 24
Jan 1 01:00:50 unknown user.info kernel: PPPoL2TP kernel driver, V0.18.3
Jan 1 01:00:50 unknown user.info kernel: PPTP driver version 0.8.5
Jan 1 01:00:50 unknown user.err kernel: pflash: found no supported devices
Jan 1 01:00:50 unknown user.warn kernel: Found an ST compatible serial flash with 128 64KB blocks; total size 8MB
Jan 1 01:00:50 unknown user.notice kernel: Creating 5 MTD partitions on "sflash":
Jan 1 01:00:50 unknown user.notice kernel: 0x00000000-0x00040000 : "pmon"
Jan 1 01:00:50 unknown user.notice kernel: 0x00040000-0x007f0000 : "linux"
Jan 1 01:00:50 unknown user.notice kernel: 0x0012c800-0x006f0000 : "rootfs"
Jan 1 01:00:50 unknown user.notice kernel: 0x006f0000-0x007f0000 : "jffs2"
Jan 1 01:00:50 unknown user.notice kernel: 0x007f0000-0x00800000 : "nvram"
Jan 1 01:00:50 unknown user.warn kernel: _nvram_init: allocat header: 2166095872, size= 61440
Jan 1 01:00:50 unknown user.warn kernel: u32 classifier
Jan 1 01:00:50 unknown user.warn kernel: OLD policer on
Jan 1 01:00:50 unknown user.warn kernel: Netfilter messages via NETLINK v0.30.
Jan 1 01:00:50 unknown user.warn kernel: nf_conntrack version 0.5.0 (512 buckets, 4096 max)
Jan 1 01:00:50 unknown user.warn kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 01:00:50 unknown user.info kernel: ipt_account 0.1.21 : Piotr Gasidlo , http://www.barbara.eu.org/~quaker/ipt_account/
Jan 1 01:00:50 unknown user.warn kernel: net/ipv4/netfilter/tomato_ct.c [Jan 19 2014 19:26:35]
Jan 1 01:00:50 unknown user.info kernel: NET: Registered protocol family 1
Jan 1 01:00:50 unknown user.info kernel: NET: Registered protocol family 10
Jan 1 01:00:50 unknown user.warn kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 01:00:50 unknown user.info kernel: NET: Registered protocol family 17
Jan 1 01:00:50 unknown user.info kernel: 802.1Q VLAN Support v1.8 Ben Greear
Jan 1 01:00:50 unknown user.info kernel: All bugs added by David S. Miller
Jan 1 01:00:50 unknown user.warn kernel: VFS: Mounted root (squashfs filesystem) readonly.
Jan 1 01:00:50 unknown user.info kernel: Freeing unused kernel memory: 128k freed
Jan 1 01:00:50 unknown user.warn kernel: Warning: unable to open an initial console.
Jan 1 01:00:50 unknown user.warn kernel: emf: module license 'Proprietary' taints kernel.
Jan 1 01:00:50 unknown user.debug kernel: PCI: Setting latency timer of device 0000:00:02.0 to 64
Jan 1 01:00:50 unknown user.warn kernel: eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.110.27.20012
Jan 1 01:00:50 unknown user.warn kernel: wl_module_init: passivemode set to 0x0
Jan 1 01:00:50 unknown user.debug kernel: PCI: Setting latency timer of device 0000:00:01.0 to 64
Jan 1 01:00:50 unknown user.warn kernel: eth1: Broadcom BCM4347 802.11 Wireless Controller 5.110.27.20012
Jan 1 01:00:50 unknown user.warn kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan 1 01:00:50 unknown user.info kernel: usbcore: registered new interface driver usbfs
Jan 1 01:00:50 unknown user.info kernel: usbcore: registered new interface driver hub
Jan 1 01:00:50 unknown user.info kernel: usbcore: registered new device driver usb
Jan 1 01:00:50 unknown user.info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 1 01:00:50 unknown user.debug kernel: PCI: Setting latency timer of device 0000:00:04.1 to 64
Jan 1 01:00:50 unknown user.info kernel: ehci_hcd 0000:00:04.1: EHCI Host Controller
Jan 1 01:00:50 unknown user.info kernel: ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
Jan 1 01:00:50 unknown user.info kernel: ehci_hcd 0000:00:04.1: EHCI Fastpath: New EHCI driver starting
Jan 1 01:00:50 unknown user.info kernel: ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
Jan 1 01:00:50 unknown user.debug hotplug[342]: Attached USB device 1-2:1.0 [INTERFACE=255/2/255 PRODUCT=a5c/bd17/1]
Jan 1 01:00:50 unknown user.info kernel: ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
Jan 1 01:00:50 unknown user.info kernel: usb usb1: configuration #1 chosen from 1 choice
Jan 1 01:00:50 unknown user.info kernel: hub 1-0:1.0: USB hub found
Jan 1 01:00:50 unknown user.info kernel: hub 1-0:1.0: 2 ports detected
Jan 1 01:00:50 unknown user.info kernel: usb 1-2: new high speed USB device using ehci_hcd and address 2
Jan 1 01:00:50 unknown user.info kernel: usb 1-2: configuration #1 chosen from 1 choice
Jan 1 01:00:51 unknown user.debug hotplug[346]: Attached USB device 1-0:1.0 [INTERFACE=9/0/0 PRODUCT=1d6b/2/206]
Jan 1 01:00:51 unknown user.warn kernel: bcm_rpc_up: waiting to be connected
Jan 1 01:00:51 unknown user.warn kernel: bcm_rpc_buf_recv_mgn_high: Reason: 0 Dongle Version: 0x5648a89
Jan 1 01:00:51 unknown user.warn kernel: bcm_rpc_buf_recv_mgn_high: Connected!
Jan 1 01:00:51 unknown user.warn kernel: eth2: Broadcom BCMa8e4 802.11 Wireless Controller 5.100.138.20
Jan 1 01:00:51 unknown user.info kernel: usbcore: registered new interface driver dbus_usbdev
Jan 1 01:00:51 unknown user.notice kernel: SCSI subsystem initialized
Jan 1 01:00:52 unknown user.info kernel: Initializing USB Mass Storage driver...
Jan 1 01:00:52 unknown user.info kernel: usbcore: registered new interface driver usb-storage
Jan 1 01:00:52 unknown user.info kernel: USB Mass Storage support registered.
Jan 1 01:00:57 unknown user.debug kernel: vlan1: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 01:00:58 unknown user.debug kernel: vlan1: add 01:00:5e:00:00:01 mcast address to master interface
Jan 1 01:00:58 unknown user.info kernel: vlan1: dev_set_allmulti(master, 1)
Jan 1 01:00:58 unknown user.info kernel: vlan1: dev_set_promiscuity(master, 1)
Jan 1 01:00:58 unknown user.info kernel: device eth0 entered promiscuous mode
Jan 1 01:00:58 unknown user.info kernel: device vlan1 entered promiscuous mode
Jan 1 01:00:58 unknown user.info kernel: device eth1 entered promiscuous mode
Jan 1 01:01:00 unknown user.info kernel: device eth2 entered promiscuous mode
Jan 1 01:01:00 unknown user.info kernel: br0: port 3(eth2) entering forwarding state
Jan 1 01:01:00 unknown user.info kernel: br0: port 2(eth1) entering forwarding state
Jan 1 01:01:00 unknown user.info kernel: br0: port 1(vlan1) entering forwarding state
Jan 1 01:01:00 unknown user.warn kernel: vlan2: Setting MAC address to c8 d7 19 f8 e2 3a.
Jan 1 01:01:00 unknown user.debug kernel: vlan2: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 01:01:00 unknown user.debug kernel: vlan2: add 01:00:5e:00:00:01 mcast address to master interface
Jan 1 01:01:01 unknown user.info kernel: IMQ starting with 2 devices...
Jan 1 01:01:01 unknown user.info kernel: IMQ driver loaded successfully.
Jan 1 01:01:01 unknown user.info kernel: Hooking IMQ after NAT on PREROUTING.
Jan 1 01:01:01 unknown user.info kernel: Hooking IMQ before NAT on POSTROUTING.
Jan 1 01:01:02 unknown authpriv.warn dropbear[489]: Failed loading /etc/dropbear/dropbear_ecdsa_host_key
Jan 1 01:01:02 unknown authpriv.info dropbear[492]: Running in background
Jan 1 01:01:02 unknown daemon.info dnsmasq[497]: started, version 2.69test3 cachesize 1500
Jan 1 01:01:02 unknown daemon.info dnsmasq[497]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP no-conntrack ipset Tomato-helper auth
Jan 1 01:01:02 unknown daemon.info dnsmasq[497]: asynchronous logging enabled, queue limit is 5 messages
Jan 1 01:01:02 unknown daemon.info dnsmasq-dhcp[497]: DHCP, IP range 192.168.1.2 -- 192.168.1.51, lease time 1d
Jan 1 01:01:02 unknown daemon.warn dnsmasq[497]: failed to access /etc/resolv.dnsmasq: No such file or directory
Jan 1 01:01:02 unknown daemon.info dnsmasq[497]: read /etc/hosts - 2 addresses
Jan 1 01:01:02 unknown daemon.info dnsmasq[497]: read /etc/dnsmasq/hosts/hosts - 3 addresses
Jan 1 01:01:02 unknown daemon.info dnsmasq-dhcp[497]: read /etc/dnsmasq/dhcp/dhcp-hosts
Jan 1 01:01:03 unknown user.debug init[1]: starting rstats.
Jan 1 01:01:03 unknown user.debug init[1]: starting cstats.
Jan 1 01:01:03 unknown user.info init[1]: Linksys E2500 v1.0: Tomato 1.28.0000 MIPSR2-116 K26 USB Max
Jan 1 01:01:03 unknown user.notice kernel: Ebtables v2.0 registered
Jan 1 01:01:03 unknown user.info kernel: device eth1 left promiscuous mode
Jan 1 01:01:03 unknown user.info kernel: br0: port 2(eth1) entering disabled state
Jan 1 01:01:04 unknown user.info kernel: device eth2 left promiscuous mode
Jan 1 01:01:04 unknown user.info kernel: br0: port 3(eth2) entering disabled state
Jan 1 01:01:04 unknown user.info kernel: vlan1: dev_set_allmulti(master, -1)
Jan 1 01:01:04 unknown user.info kernel: device eth1 entered promiscuous mode
Jan 1 01:01:04 unknown user.info kernel: br0: port 2(eth1) entering forwarding state
Jan 1 01:01:06 unknown user.info kernel: device eth2 entered promiscuous mode
Jan 1 01:01:06 unknown user.info kernel: br0: port 3(eth2) entering forwarding state
Jan 1 01:01:07 unknown daemon.info dnsmasq-dhcp[497]: DHCPREQUEST(br0) 192.168.1.36 7c:d1:c3:87:e2:d4
Jan 1 01:01:07 unknown daemon.info dnsmasq-dhcp[497]: DHCPACK(br0) 192.168.1.36 7c:d1:c3:87:e2:d4
Jan 1 01:02:52 unknown daemon.info dnsmasq-dhcp[497]: DHCPREQUEST(br0) 192.168.1.43 70:56:81:b4:b3:01
Jan 1 01:02:52 unknown daemon.info dnsmasq-dhcp[497]: DHCPACK(br0) 192.168.1.43 70:56:81:b4:b3:01 mukbook
Jan 1 01:02:55 unknown daemon.warn httpd[660]: Invalid ID 'TID8ba6c1f09b90ea' from 192.168.1.43 for /status-data.jsx
Jan 1 01:03:13 unknown daemon.warn httpd[666]: Invalid ID 'TID8ba6c1f09b90ea' from 192.168.1.43 for /status-data.jsx
Jan 1 01:14:25 unknown daemon.info dnsmasq-dhcp[497]: DHCPREQUEST(br0) 192.168.1.36 7c:d1:c3:87:e2:d4
Jan 1 01:14:25 unknown daemon.info dnsmasq-dhcp[497]: DHCPACK(br0) 192.168.1.36 7c:d1:c3:87:e2:d4
Jan 1 01:16:59 unknown daemon.info dnsmasq-dhcp[497]: DHCPREQUEST(br0) 10.202.14.229 40:6c:8f:49:c4:d3
Jan 1 01:16:59 unknown daemon.info dnsmasq-dhcp[497]: DHCPNAK(br0) 10.202.14.229 40:6c:8f:49:c4:d3 wrong network
Jan 1 01:17:00 unknown daemon.info dnsmasq-dhcp[497]: DHCPREQUEST(br0) 192.168.1.7 40:6c:8f:49:c4:d3
Jan 1 01:17:00 unknown daemon.info dnsmasq-dhcp[497]: DHCPACK(br0) 192.168.1.7 40:6c:8f:49:c4:d3

I'm not that proficient when it comes to networking, so any help at all would be greatly appreciated. I need to get my wireless working so I can actually use my Macbook Air doh.gif


Thank you!
Edited by lob3s - 1/21/14 at 10:48pm
    
CPUGraphicsRAMHard Drive
1.8 GHz Intel Core i5 Intel HD4000 4 GB 1600 MHz DDR3 256GB Toshiba 6GB/s SSD 
OSMonitorMonitorMonitor
OS X Mavericks 10.9.2 Glossy 13" 1440x900  Dell U2412M Dell U2412M 
KeyboardCaseMouseAudio
IBM Model M  IT'S LIGHT AND ALUMINUM Magic Trackpad  Schiit Magni + Modi  
Audio
Beyerdynamic DT770 Pro 80ohm 
  hide details  
Reply
    
CPUGraphicsRAMHard Drive
1.8 GHz Intel Core i5 Intel HD4000 4 GB 1600 MHz DDR3 256GB Toshiba 6GB/s SSD 
OSMonitorMonitorMonitor
OS X Mavericks 10.9.2 Glossy 13" 1440x900  Dell U2412M Dell U2412M 
KeyboardCaseMouseAudio
IBM Model M  IT'S LIGHT AND ALUMINUM Magic Trackpad  Schiit Magni + Modi  
Audio
Beyerdynamic DT770 Pro 80ohm 
  hide details  
Reply
post #2 of 6
I'd reboot the modem and also try a MAC clone on the router of the device that worked/obtained DHCP. If you change the router's WAN interface to that MAC you should get the same external IP as when the device was directly connected (assuming you change them within a minute or two of each other).
Waiting on X399
(13 items)
 
  
CPUMotherboardGraphicsRAM
AMD Phenom II B57 @ X4 3.9 Gigabyte 790FXTA-UD5 Sapphire Radeon 290 8 GB G.Skill 2133 
Hard DriveCoolingOSKeyboard
250 GB 840 EVO Noctua NH-D14 Windows 10 Logitech K350 
PowerCaseMouseMouse Pad
Seasonic x750 Corsair 600T Logitech G100s Razer Goliathus Speed 
Audio
Plantronics Gamecom 788 
  hide details  
Reply
Waiting on X399
(13 items)
 
  
CPUMotherboardGraphicsRAM
AMD Phenom II B57 @ X4 3.9 Gigabyte 790FXTA-UD5 Sapphire Radeon 290 8 GB G.Skill 2133 
Hard DriveCoolingOSKeyboard
250 GB 840 EVO Noctua NH-D14 Windows 10 Logitech K350 
PowerCaseMouseMouse Pad
Seasonic x750 Corsair 600T Logitech G100s Razer Goliathus Speed 
Audio
Plantronics Gamecom 788 
  hide details  
Reply
post #3 of 6
Thread Starter 
Quote:
Originally Posted by beers View Post

I'd reboot the modem and also try a MAC clone on the router of the device that worked/obtained DHCP. If you change the router's WAN interface to that MAC you should get the same external IP as when the device was directly connected (assuming you change them within a minute or two of each other).

There is no modem. I plug the router directly to the ethernet port in the living room. I've also tried cloning the MAC address, but that didn't solve anything.
    
CPUGraphicsRAMHard Drive
1.8 GHz Intel Core i5 Intel HD4000 4 GB 1600 MHz DDR3 256GB Toshiba 6GB/s SSD 
OSMonitorMonitorMonitor
OS X Mavericks 10.9.2 Glossy 13" 1440x900  Dell U2412M Dell U2412M 
KeyboardCaseMouseAudio
IBM Model M  IT'S LIGHT AND ALUMINUM Magic Trackpad  Schiit Magni + Modi  
Audio
Beyerdynamic DT770 Pro 80ohm 
  hide details  
Reply
    
CPUGraphicsRAMHard Drive
1.8 GHz Intel Core i5 Intel HD4000 4 GB 1600 MHz DDR3 256GB Toshiba 6GB/s SSD 
OSMonitorMonitorMonitor
OS X Mavericks 10.9.2 Glossy 13" 1440x900  Dell U2412M Dell U2412M 
KeyboardCaseMouseAudio
IBM Model M  IT'S LIGHT AND ALUMINUM Magic Trackpad  Schiit Magni + Modi  
Audio
Beyerdynamic DT770 Pro 80ohm 
  hide details  
Reply
post #4 of 6
What is your topology, exactly, then?
Waiting on X399
(13 items)
 
  
CPUMotherboardGraphicsRAM
AMD Phenom II B57 @ X4 3.9 Gigabyte 790FXTA-UD5 Sapphire Radeon 290 8 GB G.Skill 2133 
Hard DriveCoolingOSKeyboard
250 GB 840 EVO Noctua NH-D14 Windows 10 Logitech K350 
PowerCaseMouseMouse Pad
Seasonic x750 Corsair 600T Logitech G100s Razer Goliathus Speed 
Audio
Plantronics Gamecom 788 
  hide details  
Reply
Waiting on X399
(13 items)
 
  
CPUMotherboardGraphicsRAM
AMD Phenom II B57 @ X4 3.9 Gigabyte 790FXTA-UD5 Sapphire Radeon 290 8 GB G.Skill 2133 
Hard DriveCoolingOSKeyboard
250 GB 840 EVO Noctua NH-D14 Windows 10 Logitech K350 
PowerCaseMouseMouse Pad
Seasonic x750 Corsair 600T Logitech G100s Razer Goliathus Speed 
Audio
Plantronics Gamecom 788 
  hide details  
Reply
post #5 of 6
Thread Starter 
Quote:
Originally Posted by beers View Post

What is your topology, exactly, then?

I don't really know what that means.

My setup is simple. Just the router hooked up to the ethernet jack in the wall. I'm supplied with my apartment complex's internet. I also tried contacting them as well, but they just gave me the same old runaround (plug your ethernet port directly into your laptop and if it works, contact the router's manufacture because it's not our problem).
    
CPUGraphicsRAMHard Drive
1.8 GHz Intel Core i5 Intel HD4000 4 GB 1600 MHz DDR3 256GB Toshiba 6GB/s SSD 
OSMonitorMonitorMonitor
OS X Mavericks 10.9.2 Glossy 13" 1440x900  Dell U2412M Dell U2412M 
KeyboardCaseMouseAudio
IBM Model M  IT'S LIGHT AND ALUMINUM Magic Trackpad  Schiit Magni + Modi  
Audio
Beyerdynamic DT770 Pro 80ohm 
  hide details  
Reply
    
CPUGraphicsRAMHard Drive
1.8 GHz Intel Core i5 Intel HD4000 4 GB 1600 MHz DDR3 256GB Toshiba 6GB/s SSD 
OSMonitorMonitorMonitor
OS X Mavericks 10.9.2 Glossy 13" 1440x900  Dell U2412M Dell U2412M 
KeyboardCaseMouseAudio
IBM Model M  IT'S LIGHT AND ALUMINUM Magic Trackpad  Schiit Magni + Modi  
Audio
Beyerdynamic DT770 Pro 80ohm 
  hide details  
Reply
post #6 of 6
Sometimes they banned the use of Routers?
They may only allow one MAC Address per port.

It would be something to ask your landlord really.
ESXi Home Box
(6 items)
 
The Workstation.
(16 items)
 
 
CPURAMHard DriveOS
Dual L5630 72GB DDR3 RECC 120GB VERTEX 4 + 6TB RAID5 ESXi 6.0 U2 
Other
Dell PowedgeR710  
CPUGraphicsRAMHard Drive
Intel Core i5 2.4GHZ Intel Iris Pro 16GB DDR3 256GB PCI-e x2 
OSKeyboardMouse
OSX 10.11 + Win 10 Apple Wireless Keyboard Apple Magic Trackpad 
  hide details  
Reply
ESXi Home Box
(6 items)
 
The Workstation.
(16 items)
 
 
CPURAMHard DriveOS
Dual L5630 72GB DDR3 RECC 120GB VERTEX 4 + 6TB RAID5 ESXi 6.0 U2 
Other
Dell PowedgeR710  
CPUGraphicsRAMHard Drive
Intel Core i5 2.4GHZ Intel Iris Pro 16GB DDR3 256GB PCI-e x2 
OSKeyboardMouse
OSX 10.11 + Win 10 Apple Wireless Keyboard Apple Magic Trackpad 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Networking & Security
Overclock.net › Forums › Software, Programming and Coding › Networking & Security › Linksys E2500 DHCP WAN status stuck on renewing