Overclock.net banner

Compression fittings, Koolance flow sensor/display, Cougar 140mm fans (green led), Alpha UT60 560mm rads (2x),

2K views 14 replies 7 participants last post by  sunset1 
#1 ·

-Please read carefully for details. If you have questions, please send me a pm.
-I am NOT a miner and never have attempted it!
-Global shipping via usps priority or priority express only. Please pm for a shipping quote to your country.
-Shipping insurance is optional. Please pm for a quote.
-No trades please.
-Paypal or amazon payments. COD's ok (cash) for local pickup.
-Local pick ok in San Diego, CA (91950) area


-Koolance SEN-FM18T10: flow meter + temp sensor (bnib from Koolance)
-Koolance DCB-FM01: frequency adapter with 5.25 drive bay adapter (never used & included).

Selling both together since you actually need both to make it work. The sensor is brand new, replaced by Koolance under warranty. I have no way of testing it but I trust Koolance has sent a working new unit. If anything, i can assist w/ warranty on both. Only the meter and display (no other fittings/fans/parts). sold


-Phobya 3/8x1/2 "black nickel" compression fittings x20. Replaced oem o-rings with Enzotech o-rings. Distilled water ran only. sold



Sold:

-Cougar CFD 140mm green led fans. These are the best fans I've used. Very quiet and almost dead silent at 40% power. I have 30x 23xfans available.

-Alphacool UT60 560mm rads, tapped to M4, screws included (one side, hex head).

-NZXT Mix2 controller. I have a small short bay tray and the original one. Great controller, w/ 30w per channel (six channels). No issues, no whining or fan issues. You can change the led to different colors. Comes with stock cables/extensions only.

-EK Monarch X4 ram blocks, nickel/acetal, new pad will be included:sold

-Bitspower ram plates, 4x sets per kit, hardware included, pad still great shape and reusable. These were used in conjunction with the EK blocks.

-FrozenQ x4 Fusion 250mm reservoir, florescent green, new uv light added a couple of months ago (might have a spare for backup). The tube has a slight glaze most likely from the extrusion manufacturing process, though its hardly noticeable once filled with distilled. Only three plugs will be included, nothing else.

-Swiftech MCP 35X + EK CSQ acetal top + EK heatsink/housing w/ standoffs. Please note, I couldn't get the pwm to work. You may be able to fix it. Otherswise, the pump ran fine for over 1.5 years. I was able to drop the voltage using a controller and software (similar to Aquaero).
 
See less See more
2
#3 ·
Temp sensor cable is ~30", flow sensor ~27". It comes down to where you place your sensor. I had mine just temporarily set up while I did some testing at the end of my loop. The display can be mounted elsewhere w/out the drive bay bracket.
 
#5 ·
bump, added ek ram blocks and bitspower ram plates.
 
#8 ·
koolance meter sold
thumb.gif
 
#10 ·
Quote:
Originally Posted by sinnedone View Post

wermad nooooo!

you were my cougar brother. lol

Good luck with the sales, dont happen to have a 5LT do you?
wink.gif
I'm sad too but its something I've already committed too. Most of the stuff is sold already so there's no turning back at this point
frown.gif
.

bump, listing updated. I have a few more things to add, just have to take pics (rads and controller).
 
#14 ·
bump, added Koolance sensor/display & Phobya compression fittings.
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top