Overclock.net › Forums › Intel › Intel Motherboards › Asus Rampage V Extreme Owners thread
New Posts  All Forums:Forum Nav:

Asus Rampage V Extreme Owners thread - Page 812

post #8111 of 10634
Just want to confirm if this is know problems or if I have a bad board.

1) Temp sensors. Open Hardware Monitor says temp 4 is above 100C, temp 3 is above 50C and temp 6 is above 60C. Dont know what they are, but several other programs has similar temp sensor problems. Since I'm running water cooling with 2 480mm for motherboard, CPU and RAM, so should it not be lack of cooling. That is during idle with CPU temps at avg 30C, CPU package at 39C.

2) Fan headers detection problem. Half of my fans dont show up, even do I use the same number of fans and the same splitter on several of them.
This would not be that enoying, if they behaved the same when controlled. I have the same fan profile on all, yet I can tell that some fans run faster then the others.

3) Fan header and other header quality. My CPU fan header was about to fall off, just because I had a single cable hanging from it. Had to make the cable go up, in the same fashion you would to combat GPU sag. The other place I have noticed it, is the USB 3 headers. That might be do the the stiffness of the cable it self, but when you notice it after just 1 use, then something is not right.

And no, I cant RMA it, do to the fact that I have water cooled it and the heat pipe for the top one is no longer intact (takes very little to bend, once its off).

This is more a, is it worth looking at it again when I get a new motherboard?
I mean, if its this bad after one build, how will it hold up when I have a few more planned (upgrades + case modding)?

Gear mentioned in this thread:

post #8112 of 10634
1. OHM is reading sensor that doesn't even exist here. Using Aida, all the correct one are perfectly fine.
2. Fan headers are grouped. cha_fan1A and 1B are together, same for the 2A/2B, 3A/3B. You can control by group, not the individual header, this is normal.
3. By fall off, you mean it was not correctly soldered? If it's only the plastic part, then it's normal due to how those thing are manufactured. On the usb3 it's not unusual on brand knew board, I've had that multiple time. I put it in place and it's all good. Unless the plastic is damaged or melted there shouldn't be an issue. You shouldn't put strain on cable, those connector are not design for it.

The R5E along with the x99 SOC Champion are the best x99 board you can get.
CaseLabs Panda
(29 items)
 
Bench table
(18 items)
 
Fractal White
(17 items)
 
CPUMotherboardGraphicsRAM
5960X Rampage V Extreme KFA² GTX 980Ti HOF Watercooled Kingston HyperX HX426C13PB2K4/16 
RAMHard DriveHard DriveCooling
G.Skill TridentZ F4-3200C14Q-32GTZ Kingston v300 Intel SSD 535 EK-Supremacy EVO - Full Nickel 
CoolingCoolingCoolingOS
EK-Coostream XE 360 EK-Vardar F4-120ER EK-XRES 140 D5 Vario (incl. pump) Win10 / Win 8.1 / Win 7 / Linux Mint 
MonitorKeyboardPowerCase
Dell U2515H Ducky Channel Shine III MX black - white LED /... Enermax Platimax 1000w dimastech easy v3 
MouseMouse Pad
logitech G9X HyperX 900x400 / Steelseries QCK 
  hide details  
Reply
CaseLabs Panda
(29 items)
 
Bench table
(18 items)
 
Fractal White
(17 items)
 
CPUMotherboardGraphicsRAM
5960X Rampage V Extreme KFA² GTX 980Ti HOF Watercooled Kingston HyperX HX426C13PB2K4/16 
RAMHard DriveHard DriveCooling
G.Skill TridentZ F4-3200C14Q-32GTZ Kingston v300 Intel SSD 535 EK-Supremacy EVO - Full Nickel 
CoolingCoolingCoolingOS
EK-Coostream XE 360 EK-Vardar F4-120ER EK-XRES 140 D5 Vario (incl. pump) Win10 / Win 8.1 / Win 7 / Linux Mint 
MonitorKeyboardPowerCase
Dell U2515H Ducky Channel Shine III MX black - white LED /... Enermax Platimax 1000w dimastech easy v3 
MouseMouse Pad
logitech G9X HyperX 900x400 / Steelseries QCK 
  hide details  
Reply
post #8113 of 10634
Quote:
Originally Posted by KedarWolf View Post

Time to admit I'm wrong. Don't have the issue with the double boot but I disabled the cold boots and kept training on. If I don't set the RAM to 2133 first boot after changing fast boots etc. I get the black screen with the curser, won't boot. But going into the bios and putting the RAM back to 3200 on first reboot and I'm fine after that. redface.gif
did you have it wrong in the first place? redface.gif Anyway, good to know it's working as you want it to (no double-pump on boot here either)
Quote:
Originally Posted by Chiobe View Post

Just want to confirm if this is know problems or if I have a bad board.

1) Temp sensors. Open Hardware Monitor says temp 4 is above 100C, temp 3 is above 50C and temp 6 is above 60C. Dont know what they are, but several other programs has similar temp sensor problems. Since I'm running water cooling with 2 480mm for motherboard, CPU and RAM, so should it not be lack of cooling. That is during idle with CPU temps at avg 30C, CPU package at 39C.

2) Fan headers detection problem. Half of my fans dont show up, even do I use the same number of fans and the same splitter on several of them.
This would not be that enoying, if they behaved the same when controlled. I have the same fan profile on all, yet I can tell that some fans run faster then the others.

3) Fan header and other header quality. My CPU fan header was about to fall off, just because I had a single cable hanging from it. Had to make the cable go up, in the same fashion you would to combat GPU sag. The other place I have noticed it, is the USB 3 headers. That might be do the the stiffness of the cable it self, but when you notice it after just 1 use, then something is not right.

And no, I cant RMA it, do to the fact that I have water cooled it and the heat pipe for the top one is no longer intact (takes very little to bend, once its off).

This is more a, is it worth looking at it again when I get a new motherboard?
I mean, if its this bad after one build, how will it hold up when I have a few more planned (upgrades + case modding)?

As Kimir said -

ohm is (unfortunately) not updated for this platform
2 fans per controller (A and B)
The fan header is coming off the MB PCB? How'd you manage to do that?
lastly, if you get a new motherboard, skip the full cover block - 90% of problems will disappear. (and they don't do anything anyway, VRMs only need a light air flow to stay under 40C.
x99
(26 items)
 
z170/z270
(27 items)
 
x299
(10 items)
 
CPUCPUMotherboardGraphics
i7 5960X i7 6950X Asus Rampage V Extreme (STD and model-10) 2 GTX TitanXp 
GraphicsRAMHard DriveHard Drive
2 GTX Titan X Pascal GSkill 3200c14 TZs 8x8GB @ 3400c13 Intel 750 NVMe 400GB 2x Plextor SSD 256 Raid 0 (Win 7) 
Hard DriveOptical DriveCoolingCooling
Samsung NVMe 950 Pro M.2 Plextor 810 Aquacomputer GiGant 1680 (4x420) external Rad XSPC RX360 
CoolingCoolingCoolingOS
Koolance 380i Laing DDC-1T (2) Koolance EXC-800 Chiller Windows 10 x64  
OSOSMonitorMonitor
Windows 7 Pro Linux Mint ASUS Swift 1440P 144Hz Seiki 50" 4K monitor (720P-2160i) 240-30Hz 
KeyboardPowerCaseMouse
Das Keyboard Model S Pro Corsair AX1500i MicroCool Banchetto 101 Steelseries Rival 
AudioOther
Ultimate Ears TF10 Koolance Pump/Fan Controller 
CPUCPUCPUMotherboard
i5 6600K i7 7700K i3 7350 ASUS Max iX APEX, Asrock MOCF, M8Impact 
GraphicsGraphicsGraphicsRAM
ASUS GTX 1080 Turbo ASUS GTX 960 Mini EVGA GTX 550Ti G.Skill 3600c15 
RAMHard DriveHard DriveHard Drive
G.Skill 4266c19 Samsung SM951 WD VR 300 Intel 750 NVMe U.2 
Hard DriveHard DriveOptical DriveCooling
Mushkin 512 Intel 600 NVMe Raid0 Plextor DVD ROM Custom Water (Koolance 380i / XSPC 360v2) 
CoolingOSOSOS
Corsair H80iV2 (M8I) Windows 10 Pro Window 7 Linux Mint 
MonitorMonitorKeyboardPower
Seiki 4K AOC 1080P Ducky Cherry Black Silverstone 500W SFX form factor/ Seasonic 760W 
CaseMouseAudio
Bench Logitech G700s Ultimate Ears TF10s 
CPUMotherboardGraphicsRAM
7740X ASUS Rampage Apex Various G.Skill 3600c15 2x8GB kits 
Hard DriveCoolingOSKeyboard
Samsung 960 Pro, NVMe Custom Water Windows 10 Razor Black Widow 
PowerCase
Seasonic 1000 Platinum, Corsair 1500i none :-) 
  hide details  
Reply
x99
(26 items)
 
z170/z270
(27 items)
 
x299
(10 items)
 
CPUCPUMotherboardGraphics
i7 5960X i7 6950X Asus Rampage V Extreme (STD and model-10) 2 GTX TitanXp 
GraphicsRAMHard DriveHard Drive
2 GTX Titan X Pascal GSkill 3200c14 TZs 8x8GB @ 3400c13 Intel 750 NVMe 400GB 2x Plextor SSD 256 Raid 0 (Win 7) 
Hard DriveOptical DriveCoolingCooling
Samsung NVMe 950 Pro M.2 Plextor 810 Aquacomputer GiGant 1680 (4x420) external Rad XSPC RX360 
CoolingCoolingCoolingOS
Koolance 380i Laing DDC-1T (2) Koolance EXC-800 Chiller Windows 10 x64  
OSOSMonitorMonitor
Windows 7 Pro Linux Mint ASUS Swift 1440P 144Hz Seiki 50" 4K monitor (720P-2160i) 240-30Hz 
KeyboardPowerCaseMouse
Das Keyboard Model S Pro Corsair AX1500i MicroCool Banchetto 101 Steelseries Rival 
AudioOther
Ultimate Ears TF10 Koolance Pump/Fan Controller 
CPUCPUCPUMotherboard
i5 6600K i7 7700K i3 7350 ASUS Max iX APEX, Asrock MOCF, M8Impact 
GraphicsGraphicsGraphicsRAM
ASUS GTX 1080 Turbo ASUS GTX 960 Mini EVGA GTX 550Ti G.Skill 3600c15 
RAMHard DriveHard DriveHard Drive
G.Skill 4266c19 Samsung SM951 WD VR 300 Intel 750 NVMe U.2 
Hard DriveHard DriveOptical DriveCooling
Mushkin 512 Intel 600 NVMe Raid0 Plextor DVD ROM Custom Water (Koolance 380i / XSPC 360v2) 
CoolingOSOSOS
Corsair H80iV2 (M8I) Windows 10 Pro Window 7 Linux Mint 
MonitorMonitorKeyboardPower
Seiki 4K AOC 1080P Ducky Cherry Black Silverstone 500W SFX form factor/ Seasonic 760W 
CaseMouseAudio
Bench Logitech G700s Ultimate Ears TF10s 
CPUMotherboardGraphicsRAM
7740X ASUS Rampage Apex Various G.Skill 3600c15 2x8GB kits 
Hard DriveCoolingOSKeyboard
Samsung 960 Pro, NVMe Custom Water Windows 10 Razor Black Widow 
PowerCase
Seasonic 1000 Platinum, Corsair 1500i none :-) 
  hide details  
Reply
post #8114 of 10634
Quote:
Originally Posted by KedarWolf View Post

Try changing your Attempt Fast Boot, Attempt Fast Cold Boot and DRAM Training to these.

Quote:
Originally Posted by Jpmboy View Post

do so by-passes ram alignment and can result in an unstable boot even after demonstrating stability with training enabled.

i will try your solution and report back, thanks a lot, so from what i understand from u guys is that even when the ram proves stable under heavy stress testing it can falsely report instability on boot memtest and disabling this memtest will solve the boot issue? okay if that is what u truly mean but is there an explanation to why the ram or memtest does this>

again the boot issue i reported happens randomly not all the time, most of the time my pc boots normally as it should be, and that what scares the hell out of me as it happens randomly without an obvious reason!
Fusion
(20 items)
 
  
CPUMotherboardGraphicsRAM
5930k @ 4.4GHz v1.282 Rampage V Extreme Gigabyte GTX 1080TI Aorus Xtreme Corsair Dominator Platinum DDR4 2800MHz C16 v1.20 
Hard DriveHard DriveCoolingOS
Intel Solid-State Drive 750 Series 1.2TB Intel Solid-State Drive 750 Series 400GB NZXT Kraken X62 Windows 10 
MonitorKeyboardPowerCase
Samsung Plasma TV PS60F5000 60inch Corsair K95 Platinum RGB Corsair AX1500i Corsair Obsidian 650D 
MouseMouse PadAudioAudio
Corsair Glaive RGB Corsair MM800 RGB Polaris Asus Strix RAID DLX Edifier S730 2.1 
OtherOtherOtherOther
Xbox One Elite Controller Thrustmaster T500RS Thrustmaster TH8RS Steam Controller 
  hide details  
Reply
Fusion
(20 items)
 
  
CPUMotherboardGraphicsRAM
5930k @ 4.4GHz v1.282 Rampage V Extreme Gigabyte GTX 1080TI Aorus Xtreme Corsair Dominator Platinum DDR4 2800MHz C16 v1.20 
Hard DriveHard DriveCoolingOS
Intel Solid-State Drive 750 Series 1.2TB Intel Solid-State Drive 750 Series 400GB NZXT Kraken X62 Windows 10 
MonitorKeyboardPowerCase
Samsung Plasma TV PS60F5000 60inch Corsair K95 Platinum RGB Corsair AX1500i Corsair Obsidian 650D 
MouseMouse PadAudioAudio
Corsair Glaive RGB Corsair MM800 RGB Polaris Asus Strix RAID DLX Edifier S730 2.1 
OtherOtherOtherOther
Xbox One Elite Controller Thrustmaster T500RS Thrustmaster TH8RS Steam Controller 
  hide details  
Reply
post #8115 of 10634
I've a similar issue myself where it'll randomly just not post on the first attempt after cold boot. It is extremely rare though (happens maybe a couple times a months at most and it gets daily use). Not sure if it has anything to do with my long time habit of switching off my power supply when I'm done with my pc.. Maybe most of you guys don't?
Dog hair magnet
(13 items)
 
  
CPUMotherboardGraphicsGraphics
5930K @ 4.6GHz 1.28v Asus Rampage V Extreme Nvidia TITAN X (Pascal) Nvidia TITAN X (Pascal) 
RAMHard DriveHard DriveCooling
16GB Ripjaws 4 DDR4 3200  Samsung 850 pro 256GB Samsung 850 EVO 1TB Corsair H110i GTX 
OSMonitorMonitorPower
Windows 10 Pro 64bit Acer Predator XB321HK Dell U2715H Corsair AX1200i 
Case
Corsair Obsidian 750d 
  hide details  
Reply
Dog hair magnet
(13 items)
 
  
CPUMotherboardGraphicsGraphics
5930K @ 4.6GHz 1.28v Asus Rampage V Extreme Nvidia TITAN X (Pascal) Nvidia TITAN X (Pascal) 
RAMHard DriveHard DriveCooling
16GB Ripjaws 4 DDR4 3200  Samsung 850 pro 256GB Samsung 850 EVO 1TB Corsair H110i GTX 
OSMonitorMonitorPower
Windows 10 Pro 64bit Acer Predator XB321HK Dell U2715H Corsair AX1200i 
Case
Corsair Obsidian 750d 
  hide details  
Reply
post #8116 of 10634
Quote:
Originally Posted by Tideman View Post

I've a similar issue myself where it'll randomly just not post on the first attempt after cold boot. It is extremely rare though (happens maybe a couple times a months at most and it gets daily use). Not sure if it has anything to do with my long time habit of switching off my power supply when I'm done with my pc.. Maybe most of you guys don't?

actually its normal when u switch psu off as in all motherboards i used, whenever i switch off the psu or use ERP in the bios first cold boot will fail 2 seconds and then pc will run again normally i guess its the bios resetting itself or some parameters or tests of some sort, but whats weird with the asus rampage v extreme is that there is no link between switching off the psu and/or using erp and the first cold boot failing, as i do switch off the psu and then when i switch on the pc again it will do a very normal boot, cold boot fail for me is very random and cant be linked to anything, its not affecting me atm but as i said my old pc used to do it and suddenly it died, am afraid (GOD FORBID mellowsmiley.gif ) its a sign for impending death too, i really love this pc so much and spent a lot of money on it building it, beside i dont think there is a better cpu for gaming atm than a i7 5930k overclocked to 4.4ghz fully stable on all stress tests (expect prime95 as i didnt do it)
Fusion
(20 items)
 
  
CPUMotherboardGraphicsRAM
5930k @ 4.4GHz v1.282 Rampage V Extreme Gigabyte GTX 1080TI Aorus Xtreme Corsair Dominator Platinum DDR4 2800MHz C16 v1.20 
Hard DriveHard DriveCoolingOS
Intel Solid-State Drive 750 Series 1.2TB Intel Solid-State Drive 750 Series 400GB NZXT Kraken X62 Windows 10 
MonitorKeyboardPowerCase
Samsung Plasma TV PS60F5000 60inch Corsair K95 Platinum RGB Corsair AX1500i Corsair Obsidian 650D 
MouseMouse PadAudioAudio
Corsair Glaive RGB Corsair MM800 RGB Polaris Asus Strix RAID DLX Edifier S730 2.1 
OtherOtherOtherOther
Xbox One Elite Controller Thrustmaster T500RS Thrustmaster TH8RS Steam Controller 
  hide details  
Reply
Fusion
(20 items)
 
  
CPUMotherboardGraphicsRAM
5930k @ 4.4GHz v1.282 Rampage V Extreme Gigabyte GTX 1080TI Aorus Xtreme Corsair Dominator Platinum DDR4 2800MHz C16 v1.20 
Hard DriveHard DriveCoolingOS
Intel Solid-State Drive 750 Series 1.2TB Intel Solid-State Drive 750 Series 400GB NZXT Kraken X62 Windows 10 
MonitorKeyboardPowerCase
Samsung Plasma TV PS60F5000 60inch Corsair K95 Platinum RGB Corsair AX1500i Corsair Obsidian 650D 
MouseMouse PadAudioAudio
Corsair Glaive RGB Corsair MM800 RGB Polaris Asus Strix RAID DLX Edifier S730 2.1 
OtherOtherOtherOther
Xbox One Elite Controller Thrustmaster T500RS Thrustmaster TH8RS Steam Controller 
  hide details  
Reply
post #8117 of 10634
Quote:
Originally Posted by SsXxX View Post

actually its normal when u switch psu off as in all motherboards i used, whenever i switch off the psu or use ERP in the bios first cold boot will fail 2 seconds and then pc will run again normally i guess its the bios resetting itself or some parameters or tests of some sort, but whats weird with the asus rampage v extreme is that there is no link between switching off the psu and/or using erp and the first cold boot failing, as i do switch off the psu and then when i switch on the pc again it will do a very normal boot, cold boot fail for me is very random and cant be linked to anything, its not affecting me atm but as i said my old pc used to do it and suddenly it died, am afraid (GOD FORBID mellowsmiley.gif ) its a sign for impending death too, i really love this pc so much and spent a lot of money on it building it, beside i dont think there is a better cpu for gaming atm than a i7 5930k overclocked to 4.4ghz fully stable on all stress tests (expect prime95 as i didnt do it)
Mine doesn't restart itself like yours though. Just stays on till I reboot it and then posts normally second time. Again, it's extremely rare. Maybe I need to dig into my bios settings again (honestly I don't invest a lot of time in ocing, I do it for performance reasons and like to set and forget). Like you though, my stability testing (aida/realbench) was solid and I've been running it for 5 months. I do have my System Agent voltage on auto as messing with that was causing all sorts of stability issues for me. Might have to go through the hell of tweaking it again if this issue is something I should be concerned about..
Dog hair magnet
(13 items)
 
  
CPUMotherboardGraphicsGraphics
5930K @ 4.6GHz 1.28v Asus Rampage V Extreme Nvidia TITAN X (Pascal) Nvidia TITAN X (Pascal) 
RAMHard DriveHard DriveCooling
16GB Ripjaws 4 DDR4 3200  Samsung 850 pro 256GB Samsung 850 EVO 1TB Corsair H110i GTX 
OSMonitorMonitorPower
Windows 10 Pro 64bit Acer Predator XB321HK Dell U2715H Corsair AX1200i 
Case
Corsair Obsidian 750d 
  hide details  
Reply
Dog hair magnet
(13 items)
 
  
CPUMotherboardGraphicsGraphics
5930K @ 4.6GHz 1.28v Asus Rampage V Extreme Nvidia TITAN X (Pascal) Nvidia TITAN X (Pascal) 
RAMHard DriveHard DriveCooling
16GB Ripjaws 4 DDR4 3200  Samsung 850 pro 256GB Samsung 850 EVO 1TB Corsair H110i GTX 
OSMonitorMonitorPower
Windows 10 Pro 64bit Acer Predator XB321HK Dell U2715H Corsair AX1200i 
Case
Corsair Obsidian 750d 
  hide details  
Reply
post #8118 of 10634
Quote:
Originally Posted by Kimir View Post

1. OHM is reading sensor that doesn't even exist here. Using Aida, all the correct one are perfectly fine.
2. Fan headers are grouped. cha_fan1A and 1B are together, same for the 2A/2B, 3A/3B. You can control by group, not the individual header, this is normal.
3. By fall off, you mean it was not correctly soldered? If it's only the plastic part, then it's normal due to how those thing are manufactured. On the usb3 it's not unusual on brand knew board, I've had that multiple time. I put it in place and it's all good. Unless the plastic is damaged or melted there shouldn't be an issue. You shouldn't put strain on cable, those connector are not design for it.

The R5E along with the x99 SOC Champion are the best x99 board you can get.
1. Several other programs are reporting similar readings, but guess as you say, its just false readings.
2. I know fan headers are grouped, but the RPM/PWM signal should still show on all, right?
3. Yeah, I guess its the solder that was ether not applied correctly or has slightly given away. Its still on, but you have to very careful when dealing with it. And the only thing I did, was to have a cable that was just a few cm longer run down from it. When I added an extender and had the cable go up instead, it seems to do better.

I was looking at SOC Champion and MSI Godlike Carbon as the replacements.
Quote:
Originally Posted by Jpmboy View Post

lastly, if you get a new motherboard, skip the full cover block - 90% of problems will disappear. (and they don't do anything anyway, VRMs only need a light air flow to stay under 40C.
Yeah, the full cover block might create some problems and reduce the VRM temps with around 8C, but I like the look of it.
And since I will mod the case, so dont it hurt to have a bit more too look at.
post #8119 of 10634
Quote:
Originally Posted by Chiobe View Post

1. Several other programs are reporting similar readings, but guess as you say, its just false readings.
2. I know fan headers are grouped, but the RPM/PWM signal should still show on all, right?
3. Yeah, I guess its the solder that was ether not applied correctly or has slightly given away. Its still on, but you have to very careful when dealing with it. And the only thing I did, was to have a cable that was just a few cm longer run down from it. When I added an extender and had the cable go up instead, it seems to do better.

I was looking at SOC Champion and MSI Godlike Carbon as the replacements.
Yeah, the full cover block might create some problems and reduce the VRM temps with around 8C, but I like the look of it.
And since I will mod the case, so dont it hurt to have a bit more too look at.
That's the only reason to use a full cover block. thumb.gif
x99
(26 items)
 
z170/z270
(27 items)
 
x299
(10 items)
 
CPUCPUMotherboardGraphics
i7 5960X i7 6950X Asus Rampage V Extreme (STD and model-10) 2 GTX TitanXp 
GraphicsRAMHard DriveHard Drive
2 GTX Titan X Pascal GSkill 3200c14 TZs 8x8GB @ 3400c13 Intel 750 NVMe 400GB 2x Plextor SSD 256 Raid 0 (Win 7) 
Hard DriveOptical DriveCoolingCooling
Samsung NVMe 950 Pro M.2 Plextor 810 Aquacomputer GiGant 1680 (4x420) external Rad XSPC RX360 
CoolingCoolingCoolingOS
Koolance 380i Laing DDC-1T (2) Koolance EXC-800 Chiller Windows 10 x64  
OSOSMonitorMonitor
Windows 7 Pro Linux Mint ASUS Swift 1440P 144Hz Seiki 50" 4K monitor (720P-2160i) 240-30Hz 
KeyboardPowerCaseMouse
Das Keyboard Model S Pro Corsair AX1500i MicroCool Banchetto 101 Steelseries Rival 
AudioOther
Ultimate Ears TF10 Koolance Pump/Fan Controller 
CPUCPUCPUMotherboard
i5 6600K i7 7700K i3 7350 ASUS Max iX APEX, Asrock MOCF, M8Impact 
GraphicsGraphicsGraphicsRAM
ASUS GTX 1080 Turbo ASUS GTX 960 Mini EVGA GTX 550Ti G.Skill 3600c15 
RAMHard DriveHard DriveHard Drive
G.Skill 4266c19 Samsung SM951 WD VR 300 Intel 750 NVMe U.2 
Hard DriveHard DriveOptical DriveCooling
Mushkin 512 Intel 600 NVMe Raid0 Plextor DVD ROM Custom Water (Koolance 380i / XSPC 360v2) 
CoolingOSOSOS
Corsair H80iV2 (M8I) Windows 10 Pro Window 7 Linux Mint 
MonitorMonitorKeyboardPower
Seiki 4K AOC 1080P Ducky Cherry Black Silverstone 500W SFX form factor/ Seasonic 760W 
CaseMouseAudio
Bench Logitech G700s Ultimate Ears TF10s 
CPUMotherboardGraphicsRAM
7740X ASUS Rampage Apex Various G.Skill 3600c15 2x8GB kits 
Hard DriveCoolingOSKeyboard
Samsung 960 Pro, NVMe Custom Water Windows 10 Razor Black Widow 
PowerCase
Seasonic 1000 Platinum, Corsair 1500i none :-) 
  hide details  
Reply
x99
(26 items)
 
z170/z270
(27 items)
 
x299
(10 items)
 
CPUCPUMotherboardGraphics
i7 5960X i7 6950X Asus Rampage V Extreme (STD and model-10) 2 GTX TitanXp 
GraphicsRAMHard DriveHard Drive
2 GTX Titan X Pascal GSkill 3200c14 TZs 8x8GB @ 3400c13 Intel 750 NVMe 400GB 2x Plextor SSD 256 Raid 0 (Win 7) 
Hard DriveOptical DriveCoolingCooling
Samsung NVMe 950 Pro M.2 Plextor 810 Aquacomputer GiGant 1680 (4x420) external Rad XSPC RX360 
CoolingCoolingCoolingOS
Koolance 380i Laing DDC-1T (2) Koolance EXC-800 Chiller Windows 10 x64  
OSOSMonitorMonitor
Windows 7 Pro Linux Mint ASUS Swift 1440P 144Hz Seiki 50" 4K monitor (720P-2160i) 240-30Hz 
KeyboardPowerCaseMouse
Das Keyboard Model S Pro Corsair AX1500i MicroCool Banchetto 101 Steelseries Rival 
AudioOther
Ultimate Ears TF10 Koolance Pump/Fan Controller 
CPUCPUCPUMotherboard
i5 6600K i7 7700K i3 7350 ASUS Max iX APEX, Asrock MOCF, M8Impact 
GraphicsGraphicsGraphicsRAM
ASUS GTX 1080 Turbo ASUS GTX 960 Mini EVGA GTX 550Ti G.Skill 3600c15 
RAMHard DriveHard DriveHard Drive
G.Skill 4266c19 Samsung SM951 WD VR 300 Intel 750 NVMe U.2 
Hard DriveHard DriveOptical DriveCooling
Mushkin 512 Intel 600 NVMe Raid0 Plextor DVD ROM Custom Water (Koolance 380i / XSPC 360v2) 
CoolingOSOSOS
Corsair H80iV2 (M8I) Windows 10 Pro Window 7 Linux Mint 
MonitorMonitorKeyboardPower
Seiki 4K AOC 1080P Ducky Cherry Black Silverstone 500W SFX form factor/ Seasonic 760W 
CaseMouseAudio
Bench Logitech G700s Ultimate Ears TF10s 
CPUMotherboardGraphicsRAM
7740X ASUS Rampage Apex Various G.Skill 3600c15 2x8GB kits 
Hard DriveCoolingOSKeyboard
Samsung 960 Pro, NVMe Custom Water Windows 10 Razor Black Widow 
PowerCase
Seasonic 1000 Platinum, Corsair 1500i none :-) 
  hide details  
Reply
post #8120 of 10634
Quote:
Originally Posted by SsXxX View Post

No satisfactory explanation yet! Anybody?

Sounds like you have "ErP Ready" enabled.

ErP stands for Energy-related Products. The ErP Ready setting allows your system to comply with the ErP/EuP (Energy-related Products / Energy-using Products) Directive to reduce the standby power consumption of devices to less than 0.5 watts.

This is not to be confused with the "Standby" power-down inside your OS where your computer goes to sleep but quickly turns back on to your desktop within a few seconds if you move your mouse. The standby I'm talking about you can think of the state your computer is in before it cold-boots. ErP Ready disables certain features such as wake-on-lan and cold-booting with your keyboard, and only allows you to turn on the PC with the power button. ErP may also disable BIOS Flashback since occurs when the computer is in the cold powered down state.

Back when I had my x79 system, it did a similar behavior where it would turn on, turn off, then turn back on when powering up with the ErP Ready setting set to enabled. When I disabled "ErP Ready" or whatever it was called in the old system, it exhibited normal power-on behavior. I have an RVE but I do not have this enabled and have never enabled it.

edit: It could very well be some other BIOS setting too, as certain settings require a double power cycle to apply. Perhaps one of these settings requires a power cycle from cold-booting. Load optimized defaults, see if double power cycle still occurs. If it doesn't, change your settings back 1 by 1.
Edited by ssateneth - 1/31/16 at 2:52pm
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel Motherboards

Gear mentioned in this thread:

Overclock.net › Forums › Intel › Intel Motherboards › Asus Rampage V Extreme Owners thread