1. Is Deluxe using the same IR3555 integrated mosfet as Extreme? Or will IR3555 only for ROG series?
2. Since Extreme already has SupremeFX, what will differentiate it from the Formula?
3. What is different between CrystalSound and SupremeFX?
4. When is Pro and Formula boards coming?
I don't have my RVE yet, but I did have a simple question.
I have 2 SSD and 2 HDD from my old system. The 2 SSD (a 128GB and 256GB) ran on my older P6X58-D Premiums SATA3 in AHCI mode. The 2 HDD (Raptor 150GB 15krpm) were on the intel side configured as a raid 1. I read in the RVE manual that the SATA connections can only run in 1 mode. I.E. if set to RAID, all drives are set to RAID.
I am most likely incorrect, but I thought SSDs are best run in AHCI mode? If so, The single mode of the MB might cause an issue for people wanting a setup like mine? I'm most likely wrong, or at least I hope I am.
Thanks. Looking forward to my RVE and 5820K with a new Plextor M6e as a OS drive.
I'm hoping other X99 owners might be able to help me out here. I'm trying to overclock my 5960X and it's just not working with this board and I'm wondering if anyone else is seeing the same problems.
In the BIOS, it is defaulting to XMP overclocking and setting the CPU to overclock to 3750 MHz. I can change all the values, in this case, I specifically just try to set the ratio from the default 28 to 34 (I've tried everything in between, too) and the vcore to 1.31v (and I've tried 1.3v). I save and exit and the system reboots and is right back to the default XMP over clock settings.
I can occasionally get it to stay in default mode (not XMP) so the CPU runs at stock clocks, but usually it resets itself to XMP. I've tried updating the BIOS from 0505 to 0701 (and going back to 0505)... I've pulled the battery, reset the BIOS, tried DIP 5, etc... nothing seems to work.
Am I missing a key setting or switch? Do I have a bad board? Has anyone else run across these problems?
I tried switching it on and off to no effect (it's also impossible to get to when you have two graphics cards installed without removing the second card, kind of a pain.
I tried switching it on and off to no effect (it's also impossible to get to when you have two graphics cards installed without removing the second card, kind of a pain.
Check the TPU switch is not on as well. These are off by default. You may have knocked either when putting the system together. The OC being applied hints at TPU. Turn it off and load defaults by pressing F5 in UEFI if you need to.
PS. For anyone asking about availability or using this as thread as reference, the dates given are for North America only. I only cover the NA region. For others you will need to contact your local ASUS rep/channels as each region may have different availability or launch time frames.
Question! I'm on my X99 deluxe now, and there's this warning that keeps popping up on my bottom right corner.
It warns a low Vcore of 0.128V or Dram Voltage of 0.000V.
HWMonitor shows 0.9V for my Vcore and 1.2 on my Dram.
It doesn't seem to affect anything, but its really annoying to have something pop up on your screen so often.
Question! I'm on my X99 deluxe now, and there's this warning that keeps popping up on my bottom right corner.
It warns a low Vcore of 0.128V or Dram Voltage of 0.000V.
HWMonitor shows 0.9V for my Vcore and 1.2 on my Dram.
It doesn't seem to affect anything, but its really annoying to have something pop up on your screen so often.
This is called polling contention - it's because you are running more than one monitoring tool. The software is trying to poll the onboard sensor at the same time so one of them cannot report a value - hence the warning and misread. Ideally only one monitoring tool for voltages should be used at a time. You might be able to disable the monitoring of AI Suite in the options (have a look through). The only other option is to run just one tool if HWM wont let you disable some of its monitoring..
The manual is very specific so there should be no doubt or confusion regarding this. When using a M.2 drive the last x16 PCIe slot can only be used in x4 mode. As SLI requires that each card is connected by a minimum of 8 PCIe lanes this PCIe slot cannot be used for SLI when in x4 mode.
Raja, thanks for the thread again! Do you happen to know if Amazon is getting the RVE or WS anytime soon in NA?
I also had a question regarding the space between the top x16 slot and the DIMM slots in the RVE- is there enough space for a thick GPU backplate (like the active backplate from Aquacomputer) and RAM that slightly extend past the slots (like the Corsair Dom Plats)? I imagine you can't know the dimensions for those items so if you know how much space there is it would be great!
Raja, thanks for the thread again! Do you happen to know if Amazon is getting the RVE or WS anytime soon in NA?
I also had a question regarding the space between the top x16 slot and the DIMM slots in the RVE- is there enough space for a thick GPU backplate (like the active backplate from Aquacomputer) and RAM that slightly extend past the slots (like the Corsair Dom Plats)? I imagine you can't know the dimensions for those items so if you know how much space there is it would be great!
Hey there! Thanks for that info, is that for the RVE or generally any Asus board with 4 way SLI/CF support? This is just about ok for some GPU backplates but not all. Going by your posts, I assume you are affiliated with Asus so I had another question- why stop at ATX/E-ATX these days? XL-ATX is supported by a huge number of cases and offers much better PCI-E slot designs. If you have nothing to do with Asus, then I am sorry
Immediately no. In the future perhaps - as these enthusiast chipsets are usually around for a while before the next gen.
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
Ask a question
Ask a question
Overclock.net
27.8M posts
541.2K members
Since 2004
A forum community dedicated to overclocking enthusiasts and testing the limits of computing. Come join the discussion about computing, builds, collections, displays, models, styles, scales, specifications, reviews, accessories, classifieds, and more!