Overclock.net › Forums › Case Mods & Cases › Sponsored Builds & Case Mods › [Sponsored] Project no Name
New Posts  All Forums:Forum Nav:

[Sponsored] Project no Name - Page 3

post #21 of 24
Thread Starter 
Hey Guy's,

I am back with a little update, feels like I have been here before.

I took the case apart and fully strip it down to bear shell to replace the snapped motherboard tray. It felt like it took me days to de-pin all the cables that ran through the motherboard tray to the motherboard. Once I did this I tape up the perplex and mark all the holes for the motherboard standoff once I did this I tap the holes and added the standoffs.

I put the res in the same place as before but I want to change the hole for the pass through for the intake which I think will look a lot cleaner, I don't like to use a lot of fitting if I don't need to. When it came to do all the holes for my pass through hole I could not find my 20mm drill bit, so I pop on amazon and had it next day, it put me back one day, as I don't like to paint until all holes are made. While I was waiting for the drill bit I replace all the logos on the case fans to AML logo. Once I got the drill bit a few minutes later all the holes were done and it was time to paint. The paint came out great, I fitted motherboard tray back in to the case add the res, motherboard and GPU. I still need to pass all the cables back through and add the the pass through fittings.

With me taken the full case apart I am going re do the basement and make it look a little bit nicer. The build it self, I would say is nearly done and like I said in my last post that it will never be 100% complete, but I am very happy with the way it looks, just need to make sure the hard tubing is on point.

I have added photos below as always if you have any feedback or any question please post below.

Untitled by Richard Ord, on Flickr

Untitled by Richard Ord, on Flickr

Untitled by Richard Ord, on Flickr

Untitled by Richard Ord, on Flickr

Untitled by Richard Ord, on Flickr

Untitled by Richard Ord, on Flickr

Untitled by Richard Ord, on Flickr

Untitled by Richard Ord, on Flickr

Untitled by Richard Ord, on Flickr

Untitled by Richard Ord, on Flickr

Untitled by Richard Ord, on Flickr
post #22 of 24
Thread Starter 
The build is completed, hope you all enjoy the photos,

Just want to say a big thank you to all of my sponsors, Alphacool, Nanoxia, thermaltake and to the wire custom sleeving.

You can find more photos on Facebook https://www.facebook.com/AMLCustomPc/

2 by Richard Ord, on Flickr
 
IMG_5099 by Richard Ord, on Flickr 

DSC04466 by Richard Ord, on Flickr

IMG_4860 by Richard Ord, on Flickr

5 by Richard Ord, on Flickr





​​​​​​​
post #23 of 24
Very cool thumb.gif Nice work!
Gaming Rig
(14 items)
 
  
CPUMotherboardGraphicsRAM
Intel 7700K ASRock Z270 K6 Gaming Fatality RX VEGA 64 TridentZ 3600 15-15-35 
Hard DriveCoolingOSMonitor
Samsung EVO 850 Corsair H115i Windows 10 Nixeus NX-Vue24a 
KeyboardPowerCaseMouse
Corsair K70 Rapidfire  Corsair RM850X Corsair 600Q Logitech G303 
Mouse PadAudio
Steelseries Qck+ Integrated  
  hide details  
Reply
Gaming Rig
(14 items)
 
  
CPUMotherboardGraphicsRAM
Intel 7700K ASRock Z270 K6 Gaming Fatality RX VEGA 64 TridentZ 3600 15-15-35 
Hard DriveCoolingOSMonitor
Samsung EVO 850 Corsair H115i Windows 10 Nixeus NX-Vue24a 
KeyboardPowerCaseMouse
Corsair K70 Rapidfire  Corsair RM850X Corsair 600Q Logitech G303 
Mouse PadAudio
Steelseries Qck+ Integrated  
  hide details  
Reply
post #24 of 24
Thread Starter 
Thanks took a little bit longer than planned, will have the next project up soon.
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Sponsored Builds & Case Mods
Overclock.net › Forums › Case Mods & Cases › Sponsored Builds & Case Mods › [Sponsored] Project no Name