Overclock.net › Forums › AMD › AMD CPUs › AMD Ryzen Threadripper Owners Club - 1950X | 1920X | 1900X
New Posts  All Forums:Forum Nav:

AMD Ryzen Threadripper Owners Club - 1950X | 1920X | 1900X - Page 189

post #1881 of 2386
Quote:
Originally Posted by happyluckbox View Post

You are basically claiming that both blocks perform identically without pushing them to their thermal limit. It's like saying a prius and a lamborghini can both reach 70mph.


I too don't notice a much of a difference between my old kraken x62 and my new liqtech tr-4 when using aida64. The difference becomes much more prevalent (10c diference) in p95.

While I agree with you, let's take it easy on him. We're all gathering these learnings together.

I'm running the EK block right now with high temps (and 1000 mm of rad space) on my 1920X and getting very high temps on a 4.1ghz OC @ 1.35v. I've just ordered the XSPC block and will add my numbers into the mix once I get a chance to test it. Pretty certain the EK block is my bottleneck but excited to find out for sure.
post #1882 of 2386
LIQTECH TR-4 PERFORMANCE AT 4.0GHZ UPDATE


All right, I had to settle for 4.0ghz because 4.025 was requiring 1.4v to get stable.
Here are my new updated temps using the latest version of p95 with ryzen FFTs. Also, utilizing more base voltage and less LLC. My bios settings are 1.293v and normal (level 1) llc.

My temps fell by about 5c, and my maximum stable overclock jumped from 3.95ghz to 4.0ghz! So happy with my chip, guess it wasn't a dud afterall!

Cooling: liqtech tr-4 aio.

Right click on image to open new tab, and left click to magnify.




My old overclock was 73c peak, at 1.38v peak @ 3.95ghz.

My new overclock is 66c peak, at 1.38v peak, @ 4.0ghz.

Also, my voltage regulator temps fell by 14c from 94c to 80c. Something was very wrong with that old version of p95 I was using.


This is the actual performance of the liqtech tr-4. I find it to be simply amazing. Basically on par with the best custom cooling solutions out there imo.
Edited by happyluckbox - 10/19/17 at 3:36pm
post #1883 of 2386
A few questions to those of you with the Asrock X399 Taichi and Linux, have you guys got any sensors working? The it87 module doesn't seem to find any devices?


Regarding pstate OC, in the BIOS it is all greyed out and unselectable, how can I enable pstate OC? Thanks.
post #1884 of 2386
Quote:
Originally Posted by twitchyzero View Post

those with Liqtech cooler
is the Enermax LED logo flickering for you guys? My one week old 360 has that problem thinking only 1 of the EPV 8-pin was disconnected but I temps are fine...plugged in both 8-pin and still have the problem. How's their customer support?


I've found the enermax light to show pump speed. The faster the pump is running the more luminous the led. Your pump could be experiencing issues too.

Their customer support is fantastic, one of my fans was beginning to make some noise, I contacted them and they are shipping me a brand new fan. Took only 1 day! Make sure to contact them via their usa/canada site, if you are in the us/canada.
post #1885 of 2386
Quote:
Originally Posted by jugs View Post

A few questions to those of you with the Asrock X399 Taichi and Linux, have you guys got any sensors working? The it87 module doesn't seem to find any devices?


Regarding pstate OC, in the BIOS it is all greyed out and unselectable, how can I enable pstate OC? Thanks.

Iirc avanced/cbs/customized.
post #1886 of 2386
Quote:
Originally Posted by chew* View Post

Iirc avanced/cbs/customized.

Yeah that's the menu

Advanced\AMD CBS\Zen Common OPtions\Custom Pstates\Accept

All the custom Pstates are greyed out and unchangable.

Oh I think I got it, need to set OC Mode to "Customized." Thank you!
post #1887 of 2386
Warning: Spoiler! (Click to show)
Quote:
Originally Posted by jugs View Post

Yeah that's the menu

Advanced\AMD CBS\Zen Common OPtions\Custom Pstates\Accept

All the custom Pstates are greyed out and unchangable.

Oh I think I got it, need to set OC Mode to "Customized." Thank you!

yes I found that out set customized. and away you go
I only do pstate 0 and only change the speed use offset in advanced menu to adjust the voltage.

do that run balanced power in windows or whatever linux uses and it will run perfectly. Warning: Spoiler! (Click to show)
Quote:
Originally Posted by amigafan2003 View Post

I've run both the X399 EK block and the XSPC block - no difference in temps between them.

The cold plate on both blocks cover the entire heat spreader.

as of right this second I am agreeing with you I ahd the eeeeeeek block and now the xspc and so far little to no difference BUT I seem to have gotten the mother of all micro air bubbles..I did the eeeek block 3 times got rid of any air in an hour or so not having to do much.
so far I have spent nearly a day trying to bleed this bastard and only just getting there.

now if I set the pump to 1234 rpm nice and clear and loses around 5 degrees even at full whack but nice and clear as soon as I go full spec 4455rpm boom bubbles the wonder bastard BUT temps drop 5 degrees.

now I am basing my same as the eeeek block on these figures so in reality it should be 5 to 10 degrees cooler than the other block.

so yeah any tips on getting rid of them apart from shaking moving cycling pump praying and killing goats...I,m out of goats.

so in conclusion I genuinely have no problem with the eeeeeeek block on my current setup with current settings but as the other guy said ngtr whatever if you go above 1.3 to say 1.4 then the story would be a lot different. ( I have not bothered with that yet and won't till this is cleared up.

I will say though it is very nicely built easy to install and looks damn good with the red leds smile.gif go red team tongue.gif

now as for AIO I will say it again my h115i was a very nice setup with varder fans and if you were running stock you would have no issues BUT you would not get the same boost/lower power draw as you would with say the enermax with the full cover or a custom loop.

I have found more performance with the same settings using better gear it is as simple as that.

the h115i at stock would boost 4.05/4.1 but go up to and a little over 1.5 volts to do it
with the custom loop either block really it would only use 1.45 maximum and boost to 4.15 and close to 4.2
post #1888 of 2386
Quote:
Originally Posted by jugs View Post

Yeah that's the menu

Advanced\AMD CBS\Zen Common OPtions\Custom Pstates\Accept

All the custom Pstates are greyed out and unchangable.

Oh I think I got it, need to set OC Mode to "Customized." Thank you!

Yep you got it it.

Np glad i could help.
post #1889 of 2386
Is that Enermax Cooler better than the predators 360? If you have the EVO TR4 cooler?
STUDIO PC
(25 items)
 
  
CPUMotherboardGraphicsRAM
AMD Threadripper 1920X ASRock Fatal1ty X399 Professional Gaming PowerColor VEGA 64 Corsair Vengance RGB 16GB (2 x 8GB) 288-Pin DDR... 
RAMHard DriveHard DriveCooling
Corsair Vengance RGB 16GB (2 x 8GB) 288-Pin DDR... SAMSUNG EVO 850 3TB Seagate HDD EK-Supremacy EVO Threadripper Edition 
CoolingCoolingCoolingCooling
EK-XRES 100 Revo EK-CoolStream PE 360 (Triple) (Bundle Package)  EK D5 PWM (Bundle Package) EK-CoolStream PE 240 (Double) 
CoolingOSMonitorMonitor
EK-FC Radeon Vega Windows 10 HP OMEN 25" FHD 144Hz HP OMEN 25" FHD 144Hz 
KeyboardPowerCaseMouse
Logitech G910 Orion Spectrum RGB Mechanical Gam... EVGA SuperNOVA 750 B1, 80+ BRONZE 750W Phanteks Enthoo Evolv Logitech G502 Proteus Spectrum RGB Tunable Gami... 
Mouse PadAudioAudioAudio
Generic Focusrite Scarlett 2i2 Studio (1st GENERATION) ...  Logitech G933 Artemis Spectrum Focurite Scarlett CM25 Mic 
Audio
Focurite Scarlett Studio HP60 
  hide details  
Reply
STUDIO PC
(25 items)
 
  
CPUMotherboardGraphicsRAM
AMD Threadripper 1920X ASRock Fatal1ty X399 Professional Gaming PowerColor VEGA 64 Corsair Vengance RGB 16GB (2 x 8GB) 288-Pin DDR... 
RAMHard DriveHard DriveCooling
Corsair Vengance RGB 16GB (2 x 8GB) 288-Pin DDR... SAMSUNG EVO 850 3TB Seagate HDD EK-Supremacy EVO Threadripper Edition 
CoolingCoolingCoolingCooling
EK-XRES 100 Revo EK-CoolStream PE 360 (Triple) (Bundle Package)  EK D5 PWM (Bundle Package) EK-CoolStream PE 240 (Double) 
CoolingOSMonitorMonitor
EK-FC Radeon Vega Windows 10 HP OMEN 25" FHD 144Hz HP OMEN 25" FHD 144Hz 
KeyboardPowerCaseMouse
Logitech G910 Orion Spectrum RGB Mechanical Gam... EVGA SuperNOVA 750 B1, 80+ BRONZE 750W Phanteks Enthoo Evolv Logitech G502 Proteus Spectrum RGB Tunable Gami... 
Mouse PadAudioAudioAudio
Generic Focusrite Scarlett 2i2 Studio (1st GENERATION) ...  Logitech G933 Artemis Spectrum Focurite Scarlett CM25 Mic 
Audio
Focurite Scarlett Studio HP60 
  hide details  
Reply
post #1890 of 2386
ok update...got rid of most if not all the bubbles (still have the lingering feeling there are a few left)
but there's the updated results and I will admit the xspc baked beans and spaghetti block is quite a bit better than the EK block if you are pushing more load or heat or volts into it. My other results are in another post for reference all tests done with exactly the same settings including fan settings.
with the exception that in the new ones the fans are more likely to ramp up when it hits 60 so a couple of hundred rpm more.
this is done with a ek 420 CE radiator a EK-XRES 140 DDC 3.2 PWM Elite running full tilt 4500rpm and 3 3k Vardar fans running between 1200 and 1500 (at 1500 1 metre away the Db is 42 and at 1200 38)
also note I have another rad stacked on top with 2 fans pulling through that one to a 280 for video card so weird setup smile.gif as well as of course 2 pumps sitting on top so not the best setup for airflow.


also also note I have redone these tests quite a few times including gooseberry with the same results not much deviation at all.
Warning: Spoiler! (Click to show)













New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: AMD CPUs
Overclock.net › Forums › AMD › AMD CPUs › AMD Ryzen Threadripper Owners Club - 1950X | 1920X | 1900X